Stihl 1132 · Section E · 5 of 9 · 24 parts
Fan housing
Fits 019 T.
Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1132 080 3100 | Fan cover Fitment / change note → | 1 |
| 2 | 1110 084 9102 | Bushing Fitment / change note → | 1 |
| 3 | 1123 195 0400 | Rope rotor | 1 |
| 4 | 1125 195 7200 | Pawl | 1 |
| 5 | 1118 195 3500 | Spring | 1 |
| 6 | 0000 958 0923 | Washer | 1 |
| 7 | 1129 190 0601 | Rewind spring | 1 |
| 8 | 0000 195 8200 | Starter rope Ø 3x800 mm Fitment / change note → | 1 |
| 9 | 1121 195 3400 | Starter grip Fitment / change note → → replaced by 0000 190 3402 TI 43/1999 | 1 |
| 10 | 1132 967 1500 | Model plate 019 T Fitment / change note → | 1 |
| 11 | 0000 190 3402 | Starter grip ElastoStart Ø 3 mm Fitment / change note → option | 1 |
| 12 | 0000 195 7001 | Cap | 1 |
| 13 | 9075 478 4155 | Pan head self-tapping screw IS-D5x24 | 5 |
| 14 | 1132 084 1003 | Fan housing Fitment / change note → | 1 |
| 15 | 1129 967 3403 | Instruction label | 1 |
| 16 | 1132 350 7000 | Loop | 1 |
| 17 | 9104 003 3002 | Self-tapping screw IS-P4x12 | 1 |
| 18 | 9075 478 4260 | Pan head self-tapping screw IS-D5x55 | 1 |
| 19 | 0000 967 3692 | Warning pictogram Filler cap | 1 |
| 20 | 1132 080 1800 | Fan housing Fitment / change note → | 1 |
| 21 | 1132 080 1801 | Fan housing Fitment / change note → → replaced by 1132 084 1003 TI 43/1999 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1132 080 2800 | Fan cover with rewind starter Fitment / change note → | 1 |
| — | 0000 930 2208 NLA | Starter rope Ø 3 mm x 30.5 m option | 1 |
| — | 1132 080 2100 | Fan housing with rewind starter Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 019 T
019 T: engine, clutch and starter specifications
35.2 cm³, 40 mm bore, 28 mm stroke; 1.2 kW at 7,500 rpm; 12,000 rpm maximum WITH bar and chain.
- Section 2.1: displacement 35.2 cm³ (2.15 cu.in); bore 40 mm (1.57 in); stroke 28 mm (1.10 in); compression ratio 10.5:1.
- Engine power 1.2 kW (1.6 bhp) at 7,500 rpm; maximum torque 1.8 Nm (1.3 lb.ft) at 5,000 rpm. Maximum engine speed WITH BAR AND CHAIN is 12,000 rpm; mean idle speed is 2,800 rpm. These distinct conditions must not be collapsed into a no-load test setting.
- Durable built-up crankshaft; TWO deep-groove ball main bearings; needle big-end bearing; connecting rod length 51 mm (2 in); piston pin diameter 8 mm (0.3 in); needle small-end bearing. These dimensions do not identify replacement part numbers.
- Centrifugal clutch WITHOUT LININGS, 67 mm (2.64 in) diameter; engagement at APPROXIMATELY 3,700 rpm. Pawl-engagement rewind starter with automatic starter-rope rewind; rope 3.0 mm (0.12 in) diameter and 800 mm (31.5 in) long. Optional ElastoStart is listed separately on page 4.
- Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.
Source: TI 40/1996, p. 3 — engine, clutch and starter specifications.
No additional parts-table entry added.
Service note · 019 T
019 T: optional six-tooth sprocket and ElastoStart
Special accessories: 1123 640 2005 six-tooth 3/8 P spur sprocket and 0000 190 3400 ElastoStart.
- Section 3 lists SPECIAL ACCESSORIES FOR USER: 6-tooth 3/8-inch P spur sprocket 1123 640 2005 and ElastoStart 0000 190 3400. The six-tooth accessory is distinct from the standard SEVEN-tooth sprocket in section 2.6; no replacement/supersession relationship is asserted.
- Neither accessory number appears in the retained exact-019 T 2012 assembly rows. Historical assignments are carried as TI evidence on the relevant chain-drive and starter sheets, with no invented drawing position or claim of current catalog stock.
- No accessory installation sequence, included-kit list, changed rope length, required chain-loop length or measured effect on speed/starting effort is printed. The 1123 prefix does not broaden this TI’s 019 T assignment.
- Historical TI40/1996 introduction for 019 T, series 1132 only. Later 2012 catalog sheets are navigation anchors, not proof that every listed part is original 1996 equipment. No extension to MS 190 T or MS 191 T, serial cutoff or verified physical interchange. No hardware operation was performed.
Source: TI 40/1996, p. 4 — optional six-tooth sprocket and ElastoStart.
Part numbers (2)
- 1123 640 2005 — 6-tooth 3/8-inch P spur sprocketOptional user accessory, not standard 7-tooth sprocket · 019 T in TI40/1996 section 3
- 0000 190 3400 — ElastoStartOptional user accessory · 019 T in TI40/1996 section 3
Service note · 019 T
019 T C1Q-S37 fixed jet and two-opening fan housing
No high-speed adjustment screw; distinct L and LA access.
X 36 566 423 — 019 T C1Q-S37 fixed-jet carburetor and associated fan-housing introduction only; not the separately in-progress section2/3 changes.
- Zama C1Q-S37 fixed-jet carburetor 1132 120 0602 is introduced FROM X 36 566 423, WITHOUT HIGH SPEED SCREW. The historical bulletin says saws so equipped fulfill U.S. CARB AND EPA emission standards; this is not a current certification or retrofit-compliance claim.
- Fixed jet 1132 121 5600 is printed as 0.47 mm (0.018 inch diameter); preserve both printed values without adding precision. Drawing 170TI008 marks the jet 47. Drawings 170TI007/009 identify L and LA separately: LOW SPEED adjustment versus IDLE SPEED. No H screw or adjustable high-speed setting is supplied.
- The fan housing is modified to have ONLY TWO ACCESS OPENINGS for L and LA. New fan housing is 1132 080 1801; fan housing WITH REWIND STARTER is 1132 080 2101. These are different supply assemblies; no starter retrofit procedure is given.
- Page2 prints complete carburetor 1132 120 0602 across a broken table row. A separate misplaced 1132 120 3800 appears ABOVE the part-number header; page4 explicitly assigns 1132 120 3800 to the COMPLETE INTAKE CASING. This original-layout anomaly is retained, not silently promoted to a second C1Q-S37 carburetor number. Fan-sheet link is for the associated housing only; no exact C1Q-S37 carburetor sheet is retained.
- Historical 1997-21 evidence for 019 T only; not later MS successors or unlisted variants. Source-era factory supply is not current stock. No reciprocal interchange or physical verification inferred. No hardware operation was performed.
Source: TI 21/1997, p. 1 · TI 21/1997, p. 2 · TI 21/1997, p. 3 — 019 T C1Q-S37 fixed jet and two-opening fan housing.
Part numbers (4)
- 1132 120 0602 — Zama C1Q-S37 carburetorFixed-jet version; includes items1–35 · 019 T; 019 T C1Q-S37 fixed jet and two-opening fan housing; stated configuration only
- 1132 121 5600 — Fixed jet, item3; marking470.47 mm (0.018 inch) as printed · 019 T; 019 T C1Q-S37 fixed jet and two-opening fan housing; stated configuration only
- 1132 080 1801 — Fan housingTwo screw-access openings · 019 T; 019 T C1Q-S37 fixed jet and two-opening fan housing; stated configuration only
- 1132 080 2101 — Fan housing with rewind starterComplete starter/housing supply · 019 T; 019 T C1Q-S37 fixed jet and two-opening fan housing; stated configuration only
Conditional replacement · 019 T
019 T: two-opening fan housing accompanies the fixed-jet carburetor
Only L and LA access openings remain; bare housing and starter assembly have separate numbers.
X 37 623 374 — Fixed-jet C1Q-S37 and associated fan-housing modification introduced from this machine number on 019 T; retain printed X prefix. Not a whole-model production range or permission to mix carburetor internals.
- Historical TI51/1997 for 019 T, series 1132 only. The 2012 IPL is a navigation/comparison source, not proof that later C1Q-S46A internals match C1Q-S37. No extension to MS 190 T or MS 191 T. No hardware operation was performed.
- The modified fan housing is installed together with the fixed-jet carburetor from machine number X 37 623 374. It has ONLY TWO access openings, for L and LA; drawing 170TI009 KN shows their positions. No H access opening or mixture-turn setting is supplied.
- Row 39: bare fan housing 1132 080 1800 → 1132 080 1801. Row 40: fan housing WITH REWIND STARTER 1132 080 2100 → 1132 080 2101. Keep bare housing and complete starter assembly separate.
- Remark 2: every original component numbered in these rows remains available as a spare part in this 1997 bulletin. This differs from the complete WT 451 A assembly, which is no longer available from the factory under remark 1. Historical supply statements do not establish current stock.
- The later IPL retains old/new bare housings and the original starter assembly. That does not establish unrestricted retrofit or override this paired carburetor/housing production change. Last-TI 21.97 footer is a bibliographic pointer, not a delegated installation instruction.
Source: TI 51/1997, p. 1 · TI 51/1997, p. 2 — Section 2 complete, housing drawing and summary rows 39–40.
Part numbers (4)
- 1132 080 1800 — Row 39: bare fan housingOriginal version · 019 T; use only the stated original/new carburetor or housing version
- 1132 080 1801 — Row 39: bare fan housingNew version · 019 T; use only the stated original/new carburetor or housing version
- 1132 080 2100 — Row 40: housing with rewind starterOriginal version · 019 T; use only the stated original/new carburetor or housing version
- 1132 080 2101 — Row 40: housing with rewind starterNew version · 019 T; use only the stated original/new carburetor or housing version
Conditional replacement · 019 T
019 T: two-part fan housing and relocated nameplate
Separate bare-housing and complete-starter replacements from serial 2 43 983 640.
2 43 983 640 — From this serial for the019 T fan housing and ElastoStart only; not a model-identification interval or cutoff for sections3–7.
- Figure170TI010 KN shows previous ONE-PART housing above, new TWO-PART version below. The new round019 T nameplate is on the fan cover. The split is described as simplifying servicing; the drawing does not supply a retrofit procedure.
- Two replacement paths must remain distinct: old bare housing1132 080 1801 becomes housing1132 084 1003 PLUS cover1132 080 3100; old housing WITH rewind starter1132 080 2101 becomes housing1132 084 1003 PLUS cover WITH rewind starter1132 080 2800. Neither new housing alone is the complete replacement.
- Page2 table inclusions: previous item1 includes2, previous item2 includes3; new item5 includes6, new item6 includes7 and8. Bushing1110 084 9102 moves from old item3 to new item7 with unchanged number. Dashes are absent table entries, not proof the bushing was deleted.
- From serial2 43 983 640. Remark1: previous complete1132 080 2101 supplied only while existing stocks last. Remark2: previous bare1132 080 1801 remains available as spare. These are different availability rules.
- Later catalog E/doc89 lists1132 080 2100 as an older complete housing, not the TI’s1132 080 2101. Preserve the number difference; do not silently correct either or infer equivalence. It also lists old1800 and1801 bare housings; the TI replacement here names1801 only.
- Historical TI43/1999 english/USA evidence for 019 T, series1132 only. No extension to 019, 020 T, MS190 T or MS191 T from shared parts/series. Factory-availability remarks describe the historical issue, not current stock. No universal retrofit, numerical service setting or physical interchange verification is inferred.
Source: TI 43/1999, p. 1 · TI 43/1999, p. 2 — two-part fan housing and relocated nameplate.
Part numbers (7)
- 1132 080 2101 — Fan housing with rewind starterPrevious item1; includes2; stocks last · 019 T; TI43 section fan-housing
- 1132 080 1801 — Fan housingPrevious item2; includes3; remains spare · 019 T; TI43 section fan-housing
- 1110 084 9102 — BushingPrevious item3 and new item7; same number · 019 T; TI43 section fan-housing
- 1132 084 1003 — Fan housingNew item4; separate from cover · 019 T; TI43 section fan-housing
- 1132 080 2800 — Fan cover with rewind starterNew item5; includes6 · 019 T; TI43 section fan-housing
- 1132 080 3100 — Fan coverNew item6; includes7 and8 · 019 T; TI43 section fan-housing
- 1132 967 1500 — NameplateNew item8; fitted on fan cover · 019 T; TI43 section fan-housing
Conditional replacement · 019 T
019 T: ElastoStart introduction and unchanged rope
New grip from the same cutoff; the 3.0 mm × 800 mm rope number is unchanged.
2 43 983 640 — From this serial for the019 T fan housing and ElastoStart only; not a model-identification interval or cutoff for sections3–7.
- From serial2 43 983 640, standard grip 1121 195 3400 is replaced by ElastoStart 0000 190 3402. The previous grip remains available as a spare; no other-model restriction is printed here.
- New item3 includes starter rope item4,0000 195 8200,3.0 mm diameter x800 mm. Previous rope item2 has the SAME number; do not represent this as a new rope diameter, a two-rope package or substitute the020 T rope set.
- Section2 explicitly delegates construction,function,repair and servicing to TI41.98. Its 019 T adoption and the available exact 019 T workshop starter baseline are reviewed in the linked notes. Three source gaps remain: exact 019 T owner instructions; the separate General Servicing/Troubleshooting handbook (introduction calls it Standard Repairs,Troubleshooting); and an established manual revision/service baseline for the1999 two-part housing. These exact sources were not located by bounded inquiry. No 020 T,026 or brushcutter preload/direction is inherited; these are not complete repair instructions.
- Later exact019 T sheet E/doc89 lists the same grip and800 mm rope but also a separate cap. That later supply listing is not a revision of the delegated1998 complete-grip-only service statement. The shared grip number alone does not widen either bulletin’s model scope.
- Historical TI43/1999 english/USA evidence for 019 T, series1132 only. No extension to 019, 020 T, MS190 T or MS191 T from shared parts/series. Factory-availability remarks describe the historical issue, not current stock. No universal retrofit, numerical service setting or physical interchange verification is inferred.
- TI43 review is complete with documented source gaps, not a complete workshop procedure or verified physical interchange. The available manual’s ©1996 is not its edition; its old one-piece housing and ElastoStart labeling remain in tension with TI43/1999. Old-housing torque and spring settings are not silently assigned to the revised housing. Reopen when an applicable missing source becomes available.
Source: TI 43/1999, p. 2 — ElastoStart introduction and unchanged rope.
Referenced bulletin evidence: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — TI41.98 complete-grip supply,construction,function and rope service explicitly adopted for019 T by TI43 section2; adoption reviewed. Remaining owner/handbook/revision gaps are separate..
Part numbers (3)
- 1121 195 3400 — Standard starter gripPrevious item1; remains spare · 019 T; TI43 section elastostart
- 0000 190 3402 — ElastoStart starter gripNew item3; includes4 · 019 T; TI43 section elastostart
- 0000 195 8200 — Starter rope 3.0 mm x 800 mmPrevious item2 and new item4; unchanged number · 019 T; TI43 section elastostart
Conditional replacement · 019 T
019 T: unlettered filter cover and fan-cover model plate
Model designation moves to the round nameplate; introduction in progress.
- Section4 replaces1132 141 0500 with1132 141 0501. The new filter cover has NO model designation; “STIHL019 T” now appears on round nameplate1132 967 1500 on the fan cover (section1). A missing filter-cover legend is not proof of the wrong model.
- Introduction IN PROGRESS; previous filter cover supplied only while existing stocks last. Cross-reference to section1 explains label location, not an extension of its serial cutoff. Later019 T G/doc91 and E/doc89 associate the new cover and plate.
- Historical TI43/1999 english/USA evidence for 019 T, series1132 only. No extension to 019, 020 T, MS190 T or MS191 T from shared parts/series. Factory-availability remarks describe the historical issue, not current stock. No universal retrofit, numerical service setting or physical interchange verification is inferred.
Source: TI 43/1999, p. 1 · TI 43/1999, p. 3 — unlettered filter cover and fan-cover model plate.
Part numbers (3)
- 1132 141 0500 — Filter coverPrevious; stocks last · 019 T; TI43 section filter-cover
- 1132 141 0501 — Filter cover without model designationNew · 019 T; TI43 section filter-cover
- 1132 967 1500 — Round019 T nameplateOn fan cover, not filter cover · 019 T; TI43 section filter-cover
Service note · 019 T
019 T: ElastoStart force path and complete-grip service limit
The delegated grip spring smooths pulling forces; its internal parts are not a repair kit.
- TI41/1998 figures000TI028 KN and000TI029 KN identify grip1,cap2,sleeve3,coil spring4,two washers5 and rope6. At rest the sleeve,spring and washers sit within the grip. Under pull the force path is grip → lower washer → coil spring → upper washer → sleeve → rope. The grip coil spring is distinct from the rewind spring in the fan housing.
- The TI describes spring tension increasing with compression pressure and almost uniform grip force after the first compression stroke. When pull exceeds the spring-defined limit,the coil spring is fully compressed and force passes directly from grip to rope. Graph000TI007 KN has no numeric axes or units; no percentage reduction,spring load or starting-speed specification is established.
- The delegated service note supplies the grip only as a COMPLETE replacement unit and limits repairs to grip and starter rope. The internal cross-sections explain operation; they do not provide approval or instructions to rebuild the sleeve,spring or washers. The later2012 cap listing does not retroactively rewrite this1998 supply statement.
- TI43 gives the019 T grip 0000 190 3402 and unchanged rope 0000 195 8200,3.0 mm x800 mm,from serial2 43 983 640. TI41’s020 T old rope 1129 195 8200 and larger-model3401/3.5 mm sets do not become019 T parts. Its named-model backfit permission does not by itself establish a pre-cutoff019 T retrofit.
- 019 T / series1132 only. TI43/1999 explicitly adopts TI41/1998 construction,function,repair and servicing; this is not a part-number-only model association. Other TI41 model retrofits,parts and serial cutoffs are not adopted. No hardware operation or physical interchange verification.
Source: TI 43/1999, p. 2 — ElastoStart force path and complete-grip service limit.
Referenced bulletin evidence: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — Construction, operation and grip/rope service explicitly adopted by TI43/1999 section2 for019 T; no adoption of other-model parts,cutoffs or preload..
No additional parts-table entry added.
Service note · 019 T
019 T: ElastoStart rope routing and 4–7 mm knot tail
The explicit TI referral establishes the grip knot; rotor work still has a separate handbook dependency.
- TI41 page2 figure000TI030 KN: thread the complete-grip rope through the starter-housing guide bushing FROM OUTSIDE,then through the rope rotor and secure it with a SIMPLE overhand knot. “The procedure is then as before” leaves the model-specific rotor/spring sequence to its baseline; it is not a preload instruction.
- TI41 page3 figure000TI031 KN: ease the cap from the grip; remove the remaining rope from grip and rotor; fit the ElastoStart rope as standard rope but secure it IN THE GRIP with a SIMPLE overhand knot. Leave end a =4–7 mm (about1/4 inch),pull the knot into the grip and snap the cap into position. Continue as before. This tail allowance is neither total rope length nor spring preload.
- The service note requires users to be informed of the changed ElastoStart procedure and refers owner-maintained rewind-starter work to the owner manual. The exact019 T owner instructions remain to be located; do not substitute020 T instructions.
- Exact019 T manual6.4 (printed/PDF32–33) removes the fan housing per6.2 and delegates rope removal/fitting at the rotor to General Servicing,Troubleshooting. It shows cap removal,rope through the UNDERSIDE of the grip,a simple overhand knot,seating the knot and replacing the cap. TI41 supplies the explicit4–7 mm grip-tail requirement for the adopted grip.
- Manual6.5 supplies the grip complete with rope. After fan housing and delegated rotor removal,pull out and undo the rotor knot and remove old rope. Feed the new rope through the guide bush FROM OUTSIDE,through the SIDE of the rotor,then through its inner bore FROM UNDERSIDE and out at the top. Tie a simple overhand knot and pull it into the rotor recess. Rotor installation is delegated; tension per6.3.2 and refit per6.2. This sequence does not supply the missing rotor removal/installation details.
- The exact019 T manual starts at its contents page,printed/PDF1; ©1996 is a copyright year,NOT a verified publication revision. It already labels6.4–6.5 ElastoStart and depicts an older grip and ONE-PIECE housing,whereas TI43/1999 introduces the new grip and TWO-PART housing. Retain this chronology/configuration tension. These manual procedures are a configuration-bound baseline,not proof that every removal step,torque or spring setting applies unchanged to the1999 two-part assembly. The introduction requires matching IPLs,later engineering-change TIs and separate standard-repair handbooks,and retains its dealer-service/distribution notice.
- 019 T / series1132 only. TI43/1999 explicitly adopts TI41/1998 construction,function,repair and servicing; this is not a part-number-only model association. Other TI41 model retrofits,parts and serial cutoffs are not adopted. No hardware operation or physical interchange verification.
TI dependency: TI 43/1999, p. 2 — ElastoStart rope routing and 4–7 mm knot tail.
Referenced bulletin evidence: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — Construction, operation and grip/rope service explicitly adopted by TI43/1999 section2 for019 T; no adoption of other-model parts,cutoffs or preload..
Manual evidence: STIHL 019 T service manual (publication revision unestablished; ©1996), section 019 T starter dependency: introduction,6.1–6.5 and the specifically identified supporting sections, PDF pages 1, 2, 32, 33
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · 019 T
019 T: six clockwise turns in the retained workshop baseline
Exact-model evidence supplies six turns and a half-turn reserve, with the housing-revision limit preserved.
- Manual2.1 (printed/PDF3) identifies a single-pawl starter,3.0 mm x800 mm rope and minimum HALF-TURN reserve at the rope rotor. These are019 T manual values,not values printed in TI43 or a transfer from026/020 T.
- Section6.1 distinguishes dirty/pitch-clogged mechanisms from cold-thickened rewind-spring oil. For the latter it describes a few drops of paraffin/kerosene and careful repeated pull/rewind. Dirt requires removing and cleaning the mechanism,with special care at the spring. It describes washing in paraffin or white spirit,then STIHL special lubricant on rewind spring and starter post. This is historical source guidance,not a universal solvent prescription.
- Section6.3.1 removes fan housing per6.2 and delegates rope-rotor removal to General Servicing,Troubleshooting; pliers remove broken spring pieces. A replacement spring comes wire-retained and receives a few drops of special lubricant. Its retainer slips off as the spring is pressed into the housing; engage the anchor loop on the housing lug. The spring can pop out and uncoil.
- For a popped spring,the manual sets anchor-loop offset about11 mm (0.4 inch) from assembly tool 1116 893 4800’s edge. Wind COUNTERCLOCKWISE from outside inward; the wooden assembly block may assist. Slip the tool/spring over the starter post,press the spring into the housing and remove the tool. Rotor installation is delegated,then tension per6.3.2. The manual does not identify the wooden block by part number; do not borrow another model’s block number.
- Section6.3.2: make a rope loop,grip near the rotor and turn it SIX full turns CLOCKWISE. Hold the rotor,pull out and straighten the rope; hold the grip to retain tension,release the rotor and slowly allow rewind. The grip must sit firmly in the guide bush without drooping; if not,the manual adds one turn. With rope fully extended,the rotor must still turn at least another HALF TURN before maximum spring tension; otherwise hold it and remove one rope turn. Do not overtension: the spring can break. Refit fan housing. Counterclockwise spring INSTALLATION is not clockwise TENSIONING;020 T seven turns are not substituted.
- Starter-relevant tool/aid entries:11.1 item22 identifies 1116 893 4800 for installing the rewind spring.11.2 item3 specifies 0781 417 1315 for the rope-rotor bearing bore and rewind spring in the fan housing;item7 specifies GRAPHITE grease for the starter-pawl peg. No generic grease substitution or interchange is inferred. The separate rotor-removal/installation and troubleshooting handbook remains actionable source inquiry.
- The exact019 T manual starts at its contents page,printed/PDF1; ©1996 is a copyright year,NOT a verified publication revision. It already labels6.4–6.5 ElastoStart and depicts an older grip and ONE-PIECE housing,whereas TI43/1999 introduces the new grip and TWO-PART housing. Retain this chronology/configuration tension. These manual procedures are a configuration-bound baseline,not proof that every removal step,torque or spring setting applies unchanged to the1999 two-part assembly. The introduction requires matching IPLs,later engineering-change TIs and separate standard-repair handbooks,and retains its dealer-service/distribution notice.
- 019 T / series1132 only. TI43/1999 explicitly adopts TI41/1998 construction,function,repair and servicing; this is not a part-number-only model association. Other TI41 model retrofits,parts and serial cutoffs are not adopted. No hardware operation or physical interchange verification.
TI dependency: TI 43/1999, p. 2 — six clockwise turns in the retained workshop baseline.
Referenced bulletin evidence: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — Construction, operation and grip/rope service explicitly adopted by TI43/1999 section2 for019 T; no adoption of other-model parts,cutoffs or preload..
Manual evidence: STIHL 019 T service manual (publication revision unestablished; ©1996), section 019 T starter dependency: introduction,6.1–6.5 and the specifically identified supporting sections, PDF pages 1, 2, 3, 30, 31, 32, 48, 50
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · 019 T
019 T: one-piece housing removal baseline and its limits
The retained manual’s 4.0 Nm housing and 1.7 Nm hand-guard values are not silently assigned to the revised two-part housing.
- Section6.2 (printed/PDF30) shows the ONE-PIECE housing. Remove air filter per10.1; remove both fuel/oil filler caps with retainers and drain both tanks. Collect fuel and oil separately in clean containers or dispose of at an approved site. Remove handle-molding screws and fan-housing mounting screws; pull the hand guard off the housing boss and remove the housing. Refit in reverse sequence,including the pictured retainer. The text does not name that retainer more specifically.
- The printed6.2 tightening values are fan-housing screws4.0 Nm (3.0 lbf.ft) and the screw on the hand guard1.7 Nm (1.3 lbf.ft). They belong to the depicted manual configuration. TI43 supplies no replacement torque or revised dismantling sequence for its two-part housing,so these values are NOT accepted as universal1999 fan-cover fastener settings.
- The linked10.1 air-filter sequence (printed/PDF42) loosens the screw,swings the cover up and off its lugs,and removes the FELT element. It calls for a new element; knocking out or blowing clear is temporary,DO NOT WASH. On installation the element web locates in the housing recess; fit the cover over the lugs,swing down and tighten its screw. No torque is specified there. Adjacent10.2 fuel-pickup/tank-cleaning work is outside this starter dependency.
- The introduction and11.1 identify assembly stand 5910 890 3100; the saw mounts by the bar stud after removing sprocket cover and tensioner. Tool-table remarks require a torque wrench for Plastoform/DG screws;T-handle 5910 890 2400 is for RELEASING only on DG/P screws. These are historical workshop aids,not proof of universal fixture compatibility. Remaining non-starter tool/aid rows are outside this dependency review.
- The exact019 T manual starts at its contents page,printed/PDF1; ©1996 is a copyright year,NOT a verified publication revision. It already labels6.4–6.5 ElastoStart and depicts an older grip and ONE-PIECE housing,whereas TI43/1999 introduces the new grip and TWO-PART housing. Retain this chronology/configuration tension. These manual procedures are a configuration-bound baseline,not proof that every removal step,torque or spring setting applies unchanged to the1999 two-part assembly. The introduction requires matching IPLs,later engineering-change TIs and separate standard-repair handbooks,and retains its dealer-service/distribution notice.
- 019 T / series1132 only. TI43/1999 explicitly adopts TI41/1998 construction,function,repair and servicing; this is not a part-number-only model association. Other TI41 model retrofits,parts and serial cutoffs are not adopted. No hardware operation or physical interchange verification.
TI dependency: TI 43/1999, p. 2 — one-piece housing removal baseline and its limits.
Referenced bulletin evidence: TI 41/1998, p. 1 · TI 41/1998, p. 2 · TI 41/1998, p. 3 — Construction, operation and grip/rope service explicitly adopted by TI43/1999 section2 for019 T; no adoption of other-model parts,cutoffs or preload..
Manual evidence: STIHL 019 T service manual (publication revision unestablished; ©1996), section 019 T starter dependency: introduction,6.1–6.5 and the specifically identified supporting sections, PDF pages 1, 2, 30, 42, 48, 49
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the 019 T? Report a correction →