Stihl 1135 · Section H · 8 of 15 · 25 parts
AV system, Handlebar
Fits MS 361, MS 361 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1135 791 6100 | Collar screw | 1 |
| 2 | 1135 791 7200 | Sleeve | 1 |
| 3 | 1135 790 9902 | Annular buffer | 1 |
| 4 | 1135 790 9900 | Annular buffer → replaced by 1135 007 1007 TI 39/2006 | 1 |
| 5 | 9022 313 0680 | Spline screw IS-M4x16 | 2 |
| 6 | 1135 791 3100 | Spring | 1 |
| 7 | 1135 792 2900 | Bearing plug | 1 |
| 8 | 9074 478 4475 | Pan head self-tapping screw IS-P6x21.5 | 1 |
| 9 | 1135 791 2800 | Annular buffer | 1 |
| 10 | 1135 790 8300 | AV-Spring | 1 |
| 11 | 1135 790 8301 NLA | AV-Spring | 1 |
| 12 | 9022 341 0980 | Spline screw IS-M5x16 | 1 |
| 13 | 1135 791 1700 | Handlebar | 1 |
| 14 | 9074 478 4130 | Pan head self-tapping screw IS-P5x16 | 2 |
| 15 | 9074 478 4675 | Pan head self-tapping screw IS-P6x32.5 | 2 |
| 16 | 9074 478 4475 | Pan head self-tapping screw IS-P6x21.5 | 2 |
| 17 | 1135 790 3600 NLA | Wrap around handlebar | 1 |
| 18 | not sold separately | Handle hose 360 mm / 14 3/16'' not available as a separate item | 1 |
| 19 | not sold separately | Handle hose 190 mm / 7 1/2'' not available as a separate item | 1 |
| 20 | 1128 791 5501 | Elbow connector | 1 |
| 21 | 9307 021 0120 | Washer 5.3 | 1 |
| 22 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
| 23 | 9074 478 4435 | Pan head self-tapping screw IS-P6x19 | 5 |
| 24 | 1124 890 3400 NLA | Combination wrench | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 791 2009 | Handle hose Ø 19 mm x 5 m / 3/4x197'' not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 440 / MS 460 / MS 361 / MS 361 C
Stop buffer 1124 791 2800: unchanged number, conflicting increment
The printed 0.0078-inch increase does not equal 2 mm.
- Stop buffer 1124 791 2800 is modified for improved guidance and rigidity WITHOUT AN ORDER-NUMBER CHANGE. The arrow marks dimension a across the illustrated buffer; the source prints increase “0.0078 in (2 mm)” to “0.97 in (24,7 mm)”.
- CONFLICT: 0.0078 inch is about 0.198 mm, not 2 mm; 2 mm is about 0.0787 inch. Both printed increment values are retained; no corrected increment or old dimension is asserted. The nominal new dimension remains the printed 0.97 in (24.7 mm), not a manufacturing tolerance or permission to machine an old buffer.
- Continuous introduction, no serial cutoff. The summary says only the modified version is factory-available; other individual parts remain unchanged. An unchanged part number alone cannot identify old versus modified stock. The note does not state a general fitment claim for every model that ever used this number.
- Historical TI36/2005 English USA guidance only; the linked catalog sheets are navigation anchors, not proof that all later variants share these specifications. No physical interchange test was performed.
Source: TI 36/2005, p. 2 · TI 36/2005, p. 3 — Stop buffer 1124 791 2800: unchanged number, conflicting increment.
Part numbers (1)
- 1124 791 2800 — Stop bufferModified geometry, unchanged number; unit conflict · MS 440, MS 460, MS 361, MS 361 C; see note restrictions
Wrong number or missing part for the MS 361, MS 361 C? Report a correction →