Stihl 1138 · Section A · 1 of 17 · 31 parts
Crankcase
Fits MS 441, MS 441 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1138 020 2605 | Crankcase | 1 |
| 2 | 1138 020 2606 | Crankcase | 1 |
| 3 | 9503 003 0355 | Grooved ball bearing 16x35x11 | 1 |
| 4 | 9640 003 1560 | Oil seal 15x22x4 | 1 |
| 5 | 0000 988 5211 | Connector | 1 |
| 6 | 0000 988 8600 | Sleeve | 2 |
| 7 | 1138 791 5902 | Stop buffer | 1 |
| 8 | 1138 020 2903 | Crankcase | 1 |
| 9 | 1138 020 2905 | Crankcase | 1 |
| 10 | 9523 003 4278 | Grooved ball bearing 15x35x13 | 1 |
| 11 | 9640 003 1600 | Oil seal 15x29.6x4 | 1 |
| 12 | 1138 791 5903 | Stop buffer | 1 |
| 13 | 1128 640 9100 | Valve | 1 |
| 14 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 15 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 16 | 1120 162 5200 | Pin | 1 |
| 17 | 1121 162 5205 | Pin | 1 |
| 18 | 1121 162 5200 | Pin | 1 |
| 19 | 1121 162 5200 | Pin | 1 |
| 20 | 1125 162 5209 | Pin | 1 |
| 21 | 1122 647 9400 | Hose | 1 |
| 22 | 1117 640 3800 | Pickup body | 1 |
| 23 | 1138 029 0500 | Gasket | 1 |
| 24 | 1138 030 0406 | Crankshaft | 1 |
| 25 | 9455 621 1520 | Circlip 15x1 | 1 |
| 26 | 1138 664 2400 | Collar screw | 2 |
| 27 | 9022 341 1050 | Spline screw IS-M5x25 | 5 |
| 28 | 0000 350 0533 | Filler cap | 1 |
| 29 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 30 | 9022 346 0955 | Spline screw IS-M5x9.4 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1138 007 1050 | Set of gaskets option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 361 / MS 362 / MS 440 / MS 441 / MS 460 / MS 650 / MS 660 / MS 880
MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270
Metric-thread crankcase studs: Loctite 243 (USA 242) → Loctite 270; not polymer housings.
- Exact listed magnesium-crankcase models: MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880. Their metric-thread studs change from Loctite 243 (USA: Loctite 242) to Loctite 270. No stud part number, serial changeover, cure time or torque is specified here.
- Before stud reassembly, clean BOTH threads: insert the tap into the internal thread BY HAND, then blow out the threaded hole; brush off the external stud thread. Coat the cleaned stud with Loctite 270. This thread-cleaning instruction is not permission to enlarge the polymer repair-stud hole.
- Loctite is NOT used for studs in polymer engine housings. The magnesium adhesive change does not override the separate polymer repair restrictions or give these models permission to use the oversized polymer repair studs.
- The repeated words engine housings at the end of page3 are present in the original scan; they add no second instruction and are not silently corrected in the retained source.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 3 — MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270.
No additional parts-table entry added.
Wrong number or missing part for the MS 441, MS 441 C? Report a correction →