← MS 441

Stihl 1138 · Section B · 2 of 17 · 33 parts

Cylinder, Muffler

Fits MS 441, MS 441 C.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213131415161718192202122232425262728293304556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (33)

PosPart numberDescriptionQty
1 1138 020 1201 Cylinder with piston Ø 50 mm 1
2 1138 030 2003 Piston Ø 50 mm 1
3 1128 034 3000 Piston ring Ø 50x1.2 mm 2
4 4224 034 1500 Piston pin 12x8x35 1
5 9463 650 1200 Snap ring 12x1 2
6 0000 953 0807 Stud M5 1
7 9512 003 3062 Needle cage 12x15x15 1
8 1135 020 9400 Decompression valve 1
9 1138 029 2300 Cylinder gasket 1
10 9022 371 1350 Spline screw IS-M6x25 → replaced by 9022 341 1370 TI 3/1999 4
11 1138 140 2508 Manifold 1
12 9022 341 0980 Spline screw IS-M5x16 4
13 1113 141 1805 Sleeve 2
14 1110 400 7005 Spark plug Bosch WSR 6 F 1
14 0000 400 7000 Spark plug NGK BPMR7A 1
15 1138 141 3201 Cooling plate 1
16 1125 149 0601 Muffler gasket 1
17 1138 140 0655 Muffler 1
18 1135 145 9002 Plug 2
19 1135 145 9001 Plug → replaced by 1135 145 9002 TI 27/2010 2
20 1138 140 9000 Insulating pad 1
21 1138 140 0654 Muffler 1
22 1138 140 0653 Muffler 1
23 1138 140 8100 Spark arresting screen 1
24 9039 448 0656 Self-tapping screw M4x9.6 1
25 1138 145 8600 Screen 1
26 9099 021 0810 Self-tapping screw 4.2x9.5 1
27 9022 341 0983 Spline screw IS-M5x16 2
28 1138 148 0700 Collar screw 2
29 9220 260 0700 Hexagon nut M5 2
30 9331 630 0120 Conical spring washer 5 2
Not numbered on the diagram — assemblies, kits and options
— 1138 007 1006 Manifold kit 1
— 1138 007 1050 Set of gaskets option 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · MS 441 / MS 441 C-Q

MS 441 / C-Q: 2006 engine design and specifications

Four-port stratified scavenging, 70.7 cm³ engine, ignition, capacities and original cutting-equipment options; historical specifications, not later M-Tronic settings.

  • English USA TI 14/2006 introduction only: MS 441 and MS 441 C-Q, not later M-Tronic configurations. No production serial cutoff or universal interchange is established.
  • The piston-skirt control slot connects separate fresh-air ports to transfer ports without additional fresh-air control components. On intake/compression, mixture enters the crankcase while fresh air enters the transfer ports. Ignition occurs shortly before TDC; downstroke compresses crankcase mixture and transfer air. Exhaust opens before transfer ports; fresh air scavenges exhaust first, then mixture enters and mixes with remaining air. Diagrams 000TI 043–047 explain gas paths, not port timing dimensions or replacement-part geometry.
  • High power and wide-range torque, up to 20% lower fuel consumption than conventional two-strokes, roughly doubled filter life versus MS 440 and low vibration are source claims, not reproduced measurements. Intended use is timber harvesting and general timber work. ElastoStart plus combines the starter handle and decompression valve; MS 441 optionally has heated handles and carburetor heating. C-Q has the additional dual chain brake.
  • Single-cylinder two-stroke: 4.31 cu in (70.7 cm³), bore 1.97 in (50 mm), stroke 1.41 in (36 mm); ISO 7293 output 5.5 hp (4.1 kW) at 9,500 rpm. Idle 2,800 rpm; permissible maximum with guide bar and chain 13,500 rpm. These are printed specifications, not a bare-engine speed authorization.
  • Weight without guide bar and chain: MS 441 14.5 lb (6.60 kg); heated-handle MS 441 and MS 441 C-Q each 14.7 lb (6.70 kg). Electronic ignition has automatic timing adjustment; suppressed NGK BPMR 7 A plug, gap 0.020 in (0.5 mm). No spark-plug order number is supplied.
  • Fuel capacity 1.53 US pt (0.725 litres). Fuel mixture is referred to the owner manual, not specified here. Speed-dependent rotary-piston oil pump has additional manual flow control; oil capacity 0.76 US pt (0.360 litres). Large accessible tank openings and quick filler-cap operation are described, without cap order numbers or conversion claims.
  • Rollomatic or Duromatic bars; listed chains Rapid Micro 2, Rapid Micro, Rapid Super, Rapid Super C and Rapid Super C 3; pitch 3/8 in. Rim sprocket 7 teeth, optional 8 teeth. No bar length, gauge, drive-link count or complete compatible-loop ordering data is given.
  • Exact applicable MS 441 owner and service manuals are not established by the bounded local manual filename inventory or admitted reader manuals. Do not invent mixture ratio, torque values or a complete service procedure. Section 4.6 locates the serial number on the side of the crankcase; the drawing is a location guide, not a production cutoff.

Source: TI 14/2006, p. 1 · TI 14/2006, p. 2 · TI 14/2006, p. 3 · TI 14/2006, p. 4 · TI 14/2006, p. 7 · TI 14/2006, p. 8 · TI 14/2006, p. 16 — Cover; sections1.1–1.1.5,1.6,2.1–2.5,4.4–4.6.

No additional parts-table entry added.

Service note · MS 441 / MS 441 C-Q

MS 441 / MS 441 C-Q: matched shroud and decompression-valve grommet

Old and new shrouds require their corresponding grommets.

  • Previous shroud 1138 084 0900 becomes 1138 084 0902. New shroud has modified COOLING-AIR ROUTING and easier mounting/removal; original figure 219TI043 shows old LEFT, new RIGHT. No quantified cooling or performance improvement is supplied.
  • Cylinder grommet 1138 028 1002 becomes 1138 028 1004, adapted to the new shroud. Prose describes a LARGER RECESS for the decompression valve; figure 219TI044 captions say previous WITHOUT RECESS, new WITH RECESS. Both descriptions are retained, not converted into invented dimensions.
  • Old grommet 1138 028 1002 can ONLY be combined with OLD shroud 1138 084 0900 and remains available for older machines. New grommet 1138 028 1004 can ONLY be combined with NEW shroud 1138 084 0902; the new shroud likewise requires the new grommet. No mixed old/new pairing is approved.
  • Previous shroud is factory supplied only WHILE STOCKS LAST. Modification introduction is CONTINUOUS, without a numeric serial boundary.
  • Source explicitly names MS 441 and MS 441 C-Q, series 1138. MS 441 provides an exact catalog navigation anchor; the shared IPL label MS 441 C is NOT asserted to be an exact C-Q alias or permission for other C variants.
  • Historical English 2009 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 13/2009, p. 1 · TI 13/2009, p. 2 — MS 441 / MS 441 C-Q: matched shroud and decompression-valve grommet.

Part numbers (4)
  • 1138 084 0900 — Previous shroudOnly previous grommet; stocks last · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 084 0902 — New shroudOnly new grommet · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 028 1002 — Previous cylinder grommetOnly old shroud; older-model supply · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 028 1004 — New cylinder grommetOnly new shroud; valve recess · MS 441 / MS 441 C-Q; source restrictions apply

Service note · MS 441 / MS 441 C-Q

MS 441 / MS 441 C-Q: two shroud-kit numbers with different included parts

Kit 1650 includes one grommet; the summary separately lists kit 1651 with a set.

  • Section 1.3 names NEW shroud kit 1138 080 1650 for older machines, including modified cylinder grommet 1138 028 1004. Summary item 3 repeats1650, includes item 4, and has older-machine/service-note remarks 1/2.
  • Summary item 2 separately lists old kit 1138 080 1601 to NEW 1138 080 1651, INCLUDING ITEM5 (set of grommets). Remarks1/4 permit older machines and retain old kit only while stocks last. The printed1650 and1651 are BOTH retained as different listed packages, not silently corrected to one number.
  • The prose says the new shroud kit does NOT include grommets 1138 028 1000 or 1138 028 1001; procure them separately if needed. This statement occurs with the prose’s1650 kit; the TI does NOT enumerate the full contents of1651 or its grommet set, so do not infer those two grommets are included in1651.
  • Previous shroud 1138 084 0900 and old kit 1138 080 1601 remain available only WHILE STOCKS LAST. Retrofit permission for a complete kit does not permit mismatched new shroud/old cylinder grommet.
  • Source explicitly names MS 441 and MS 441 C-Q, series 1138. MS 441 provides an exact catalog navigation anchor; the shared IPL label MS 441 C is NOT asserted to be an exact C-Q alias or permission for other C variants.
  • Historical English 2009 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 13/2009, p. 2 — MS 441 / MS 441 C-Q: two shroud-kit numbers with different included parts.

Part numbers (6)
  • 1138 080 1601 — Previous shroud kitWhile stocks last · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 080 1650 — Shroud kit including cylinder grommetProse and summary item 3 · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 080 1651 — Shroud kit including grommet setSummary item 2; distinct package · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 028 1004 — Modified cylinder grommetIncluded in1650 · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 028 1000 — GrommetNot included by prose kit description · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 028 1001 — GrommetNot included by prose kit description · MS 441 / MS 441 C-Q; source restrictions apply

Service note · MS 441 / MS 441 C-Q

MS 441 / MS 441 C-Q: grommet-set replacement and old-shroud service supply

The new set is restricted to the new shroud; old-shroud grommets become individual purchases.

  • Set of grommets 1138 007 1001 becomes 1138 007 1005. NEW SET 1138 007 1005 can ONLY be combined with NEW SHROUD 1138 084 0902.
  • Old set 1138 007 1001 remains available only WHILE STOCKS LAST. After exhaustion, grommets for OLD SHROUD 1138 084 0900 must be procured INDIVIDUALLY. This is not permission to substitute the new set into an old shroud.
  • Summary item 5 repeats the set replacement and service-note/stock-exhaustion remarks 2/4. No complete set contents, individual quantities or present-day availability are established by this historical source.
  • Source explicitly names MS 441 and MS 441 C-Q, series 1138. MS 441 provides an exact catalog navigation anchor; the shared IPL label MS 441 C is NOT asserted to be an exact C-Q alias or permission for other C variants.
  • Historical English 2009 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 13/2009, p. 2 — MS 441 / MS 441 C-Q: grommet-set replacement and old-shroud service supply.

Part numbers (4)
  • 1138 007 1001 — Previous grommet setStocks last; then individual old-shroud parts · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 007 1005 — New grommet setOnly new shroud 1138 084 0902 · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 084 0900 — Previous shroudIndividual grommets after old-set exhaustion · MS 441 / MS 441 C-Q; source restrictions apply
  • 1138 084 0902 — New shroudRequired by new set · MS 441 / MS 441 C-Q; source restrictions apply

Wrong number or missing part for the MS 441, MS 441 C? Report a correction →