Stihl 1138 · Section K · 10 of 17 · 33 parts
Carburetor bracket, Air filter
Fits MS 441, MS 441 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (33)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1138 120 0909 | Carburetor bracket | 1 |
| 2 | 1138 122 3100 | Felt | 1 |
| 3 | 1138 442 1600 | Contact spring | 1 |
| 4 | 1138 182 0900 | Switch shaft | 1 |
| 5 | 1138 121 8600 | Washer | 1 |
| 6 | 0000 958 0528 | Washer | 2 |
| 7 | 0000 958 0513 | Washer | 2 |
| 8 | 1138 122 9501 | Preheater plate | 1 |
| 9 | 1138 140 2508 | Manifold | 1 |
| 10 | 1138 121 2600 | Air guide inlet | 1 |
| 11 | 1138 121 4100 | Air guide outlet | 1 |
| 12 | 1138 120 0600 | Carburetor HD-41B | 1 |
| 13 | 1124 121 9100 | Bushing | 1 |
| 14 | 1138 141 0900 | Filter base | 1 |
| 15 | 1138 141 0901 | Filter base | 1 |
| 16 | 1138 120 8200 | Buffer | 2 |
| 17 | 9216 261 0700 | Hexagon nut M5 | 4 |
| 18 | 1138 120 4102 NLA | Baffle | 1 |
| 19 | 1138 140 9303 | Twist lock | 1 |
| 20 | 9645 951 3007 | O-ring 3x3 | 1 |
| 21 | 1138 140 9500 | Slotted nut | 1 |
| 22 | 0000 140 4402 | Air filter HD2 | 1 |
| 23 | 0000 120 1653 | Air filter, wire mesh option | 1 |
| 24 | 0000 141 0300 | Prefilter | 1 |
| 25 | 1138 140 1501 | Inner housing | 1 |
| 26 | 1138 141 9600 | Rubber buffer | 4 |
| 27 | 1138 140 1600 | Snap closure | 2 |
| 28 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 4 |
| 29 | 1138 123 7500 | Grommet | 1 |
| 30 | 1138 123 7501 | Grommet | 1 |
| 31 | 1138 141 1001 | Carburetor box cover | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1138 007 1006 | Manifold kit | 1 |
| — | 1138 120 4103 NLA | Baffle | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 441 / MS 441 C-Q
MS 441: pre-separation, AV system and winter cover
Air cleaning and carburetor preheating use separate paths; cover kit 1138 007 1000 is for extreme winter conditions.
- English USA TI 14/2006 introduction only: MS 441 and MS 441 C-Q, not later M-Tronic configurations. No production serial cutoff or universal interchange is established.
- A ramp ahead of the ignition module swirls and deflects intake air: larger/heavier dirt is thrown upwards and outwards; pre-cleaned air travels through the pre-separation duct to the filter. The diagram does not specify a replacement filter or a cleaning interval.
- AV section 1.4 shows springs 1 and 3, spring 2 with integrated overload protection, Cellasto element 4 and two Cellasto stop buffers 5. Diagram callouts are local, not order numbers; no unprinted spring substitution is asserted.
- Carburetor carrier 1 and plate 2 form the preheating channel. Cylinder-warmed air enters through slide 3 and leaves opening 4, heating the plate and carburetor. Cold pre-cleaned air still enters through the separate intake duct, maintaining the charge. Do not equate this air/plate heating arrangement with the optional electrical carburetor heater.
- Cover plate kit 1138 007 1000 prevents powdery or drifting snow entering the machine in extreme winter conditions: the source prints temperatures below 15 °F or −10 °C, powdery or drifting snow. Retain those printed thresholds rather than treating them as exact mathematical equivalents. No kit contents, fitting sequence or normal-weather operating rule is supplied.
Source: TI 14/2006, p. 2 · TI 14/2006, p. 6 · TI 14/2006, p. 12 — Sections1.3–1.5 and3.3.
Part numbers (1)
- 1138 007 1000 — Winter cover plate kitSpecial user accessory · 2006 MS441 configuration; extreme winter conditions
Wrong number or missing part for the MS 441, MS 441 C? Report a correction →