← E140/E160/E180 · MSE 140/141/160/180/200

Stihl 1208 · Section C · 3 of 4 · 30 parts

Handle housing

Fits E 140, E 160, E 180 C.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
111011121314151617181922021222324252627282933456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (30)

PosPart numberDescriptionQty
1 1208 640 7550 Spur gear Fitment / change note → 1
2 1206 642 7600 Slotted nut 1
3 1206 642 7801 Washer 2
4 1208 351 0300 Oil tank 1
5 1208 647 9100 Grommet 1
6 0000 359 1200 Sealing ring 1
7 1208 790 1003 Handle housing 1
8 1123 021 2800 Insert 1
9 9513 003 2280 Needle cage 10x14x10 1
10 1123 664 2400 Collar screw 1
11 1208 664 2400 Collar screw 1
12 9074 478 3075 Pan head self-tapping screw IS-P4x19 7
13 1123 664 0501 Bumper spike 1
14 9074 478 4135 Pan head self-tapping screw IS-P5x20 2
15 1206 642 7810 Washer 1
16 1206 642 1301 Chain sprocket 3/8" Picco 7T 1
17 1208 642 1301 Chain sprocket 1/4" 8T option 1
18 0000 958 0506 Washer 1
19 9460 624 0801 E-clip 8x1.3 1
20 1120 664 1500 Tensioning nut 1
21 1123 664 1605 Adjusting screw 1
22 1123 664 2205 Cover 1
23 1123 007 1004 Spur gear / chain adjusting screw kit 1
24 1123 640 1900 Tensioner slide 1
25 1123 664 1400 Thrust pad 1
26 1123 664 2200 Cover 1
27 1206 640 3600 Oil filler cap 1
28 1117 350 0905 Filler cap retainer 1
29 9099 021 2360 Self-tapping screw 3.5x9.5 1
Not numbered on the diagram — assemblies, kits and options
— 1123 007 1000 Chain tensioner kit 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · E 140 / E 160 / E 180 C

E-series handle access: needle sleeve support and oil-tank seals

Keep removal and installation support sides distinct.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 4.1 removes the quick tensioner if fitted (7.3); unfold its wingnut handle, unscrew and remove the sprocket cover. The wingnut can be eased out and refitted until it snaps into the cover. Models with quick tensioner also require removal of the spiked bumper; do not silently apply this step to every variant.
  • For all models, 6.1 removes the E-clip and outer washer, chain sprocket, then inner washer. Section 4.1 removes oil filler cap with retainer, housing screws and handle housing. For needle-sleeve removal, remove O-ring and support the bearing bush FROM OUTSIDE using a socket (19 mm is an example); press with drift 1111 893 4700.
  • For refitting, use a NEW O-ring on the gear-housing pivot pin. Support the bush FROM INSIDE with a socket and install needle sleeve with arbor 4116 893 7205. Inspect oil-tank sealing ring and replace if necessary. Handle-housing screws: 2.0 Nm (1.5 lbf.ft).
  • Section 9.1 removes the oil tank after handle-housing access, pulling it off the strainer at the same time; remove sealing ring and grommet, refit in reverse. Section 9.2 pulls strainer off stub, cleans and inspects it, replacing if damaged. This is not an oil-pump output test or pump-overhaul closure.
  • The adjacent cord-replacement steps are not required merely to access the rotor. If cord work is performed, 4.1 removes clamp screws and switch wires, transfers protector THIN END FIRST, checks its seating and tightens strain-relief clamp to 1.5 Nm (1.1 lbf.ft). No invented conductor length, ferrule size or switch-terminal torque is supplied.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series handle access: needle sleeve support and oil-tank seals.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series handle access: needle sleeve support and oil-tank seals, PDF pages 3, 7, 8, 16, 19, 22

Part numbers (2)
  • 1111 893 4700 — Assembly driftLater manual service reference · Needle sleeve removal; exact later E-series manual scope
  • 4116 893 7205 — Press arborLater manual service reference · Needle sleeve installation; exact later E-series manual scope

Service note · E 140 / E 160 / E 180 C

E-series brake switch lever: pawl and torsion spring orientation

The torsion spring is not either of the two tension springs.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 8.1 removes gear housing via 5.2 and brake drum via 5.4 IF NECESSARY. Carefully pull switch lever off pivot, disconnect brake rod from pawl, pry pawl from lever and remove torsion spring.
  • Refit in reverse and check installed torsion-spring position against 100RA090. Its two indicated seating locations are illustrated; the source gives no angular preload, coil-count adjustment or stand-alone interchange rule.
  • The adjacent left-column 7.3 quick-tensioner wingnut instructions belong to cover access, not the brake-pawl assembly. Keep the torsion spring, flat spring and the two tension springs distinct.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series brake switch lever: pawl and torsion spring orientation.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series brake switch lever: pawl and torsion spring orientation, PDF pages 3, 7, 19

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Service note · E 140 / E 160 / E 180 C

E-series polymer fasteners: re-engage the existing thread

Power-driver ceilings are not substitutes for a torque wrench.

  • Later-source comparison: RA_100_00_01_02, cover 2003-01, contents copyright 1998, production stamp 2006-03-02. Its introduction expressly covers E 140, E 160 and E 180 C with model-specific exceptions. This is NOT proof of the exact manual supplied in 1997, MSE applicability or electrical-version interchange.
  • Section 2.4 requires torque wrench use for Plastoform screws. In an existing thread, rotate P screw COUNTERCLOCKWISE until it drops slightly, then tighten clockwise to specified torque; this is intended to re-engage the existing thread, not form a new one.
  • Printed power-driver speed ceilings in polymer: Plastoform maximum 600 rpm; DG maximum 500 rpm. These are different screw families, not generic motor rpm limits.
  • Hot-air warming can ease release of adhesive-secured screws/nuts; the manual warns to protect polymer components. The tool-table footnote restricts the indicated hand screwdrivers to RELEASING ONLY on Plastoform screws; tightening still requires torque control.
  • No hardware operation was performed. Unplug before repair; the manual requires post-repair high-voltage insulation testing by electricians or specially trained personnel. This source summary does not provide missing test voltage/duration/acceptance values or establish a verified repair.

TI dependency: TI 2/1997, p. 3 — E-series polymer fasteners: re-engage the existing thread.

Later manual evidence: STIHL E 140, E 160, E 180 C service manual (2003-01), section E-series polymer fasteners: re-engage the existing thread, PDF pages 3, 5, 7, 24

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Conditional replacement · E 140 / E 180 C

E 140 / E 180 C: improved ring gear and pinion supplied as a matched set

Always replace both gears together; the printed heading does not name E 160.

  • The printed heading AND last-TI line say E 140, 180 C, series 1208. Retained metadata title adds E 160 and omits the C qualifier. This note follows the ORIGINAL PAGE: E 140 and E 180 C only. E 160 applicability is NOT established by this TI, even though it shares the catalog sheet; no MSE applicability is inferred from the shared 1208 series or reused number.
  • Improved tooth geometry is intended to increase wear life. Original ring gear 1208 640 7500 and drive pinion 1206 642 0401 are replaced by modified versions available ONLY AS A SET under 1208 640 7550. ALWAYS replace the ring gear AND drive pinion TOGETHER. Do not mix an original gear with a modified mate or treat availability of the old pinion for other models as permission to mix them.
  • The figure 100TI004 KN labels ring gear (1) and drive pinion (2). The SUMMARY uses DIFFERENT item numbering: item 1 original ring gear; item 2 new ring-gear set including item 3 drive pinion. Figure callout 2 is NOT summary item 2. No tooth count, ratio, module, dimensions or new standalone pinion number is given.
  • Summary: original ring gear 1208 640 7500 and pinion 1206 642 0401 each have -*- in the new column; remark 1 says the NEW version is not available separately. New set 1208 640 7550 has --- in the original column and includes item 3. Remark 2 applies ONLY to the original drive pinion: it remains available for OTHER MODELS, which are not named. Do not extend that availability statement to the old ring gear.
  • Introduction is IN PROGRESS: no serial cutoff is supplied. Retained E 140/E 160/E 180 C handle-housing sheet lists 1208 640 7550 as Spur gear at position 1; bind that exact number without changing IPL rows or claiming E 160 coverage. The later MSE sheet reuses this number but is not a TI32/1998 model binding. Last TI02.97 is a bibliographic pointer, not a missing prerequisite for this self-contained change.
  • No hardware operation was performed. Historical factory supply is not current stock or verified physical interchange.

Source: TI 32/1998, p. 1 — Complete page: printed model scope, improved tooth geometry, matching-set service rule, figure, all three summary rows, both remarks and footer.

Part numbers (3)
  • 1208 640 7500 — Original ring gearReplaced by matched set · E 140 / E 180 C; no individual modified gear
  • 1206 642 0401 — Original drive pinionReplaced by matched set; old version retained for unnamed other models · E 140 / E 180 C; always replace both gears
  • 1208 640 7550 — Ring gear set including drive pinionNew matched set only · E 140 / E 180 C; introduction in progress

Conditional replacement · E 140

E 140: overload breaker, revised housing and reset limits

The 120 V, 1400 W breaker begins at serial 1 43 792 970. Original wiring is transcribed with terminal-label limits; the delegated owner-manual Chain Brake chapter remains a documented source gap, so this is not a complete installation procedure.

  • TI33/1999 covers model E 140, series 1208. From serial 1 43 792 970 it receives an overload circuit breaker described as the same as that in E 180 C. The part summary specifies 120 V, 1400 W. This does not establish another mains-voltage version, a current-trip rating, E 160 fitment or compatibility with later MSE models. The grouped IPL is navigation only; the asserted model remains E 140.
  • The breaker interrupts the power supply during a mechanical overload. The source examples are excessive feed force lugging down the motor and a chain pinched in the cut. It is not described as a substitute for the chain brake or as proof that every failure to start is an overload trip.
  • The E 140-only housing 1208 790 1011 is deleted and replaced by 1208 790 1015, already available for E 180 C. The summary adds breaker 1208 430 1500 and packing ring 1206 435 8000; the ring is also already available for E 180 C. Wires 1208 440 1900 and 1208 440 1905 have dashes in the new column, not replacement numbers. Remark 1 says the previous housing and both wires are no longer available from the factory. These are historical availability statements, not current stock or permission to discard necessary wiring.
  • The source allows backfitting the breaker to older machines. Drawing 100TI000 KN specifies drilling an 11 mm diameter hole from inside the handle housing at the illustrated location. It does not provide a measured offset, tolerance, drill depth, installation torque or general drilling permission for other housings. No dimensional location is inferred by measuring the image.
  • Diagram 100TI006 KN uses component callouts 1 trigger switch, 3 overload circuit breaker, 4 chain brake switch, 5 brush holder with carbon brush (two shown), 6 rotor and 7 stator. These are not terminal numbers. The paired power-cable conductors enter the left-hand trigger-switch terminals labeled 2 (upper) and 1 (lower); the right-hand output terminals repeat 2 and 1. No line/neutral, wire color, conductor size or mains polarity is assigned by this drawing.
  • Visible external connections in the original drawing: trigger-switch right-hand terminal 2 goes to breaker terminal 1; breaker terminal 3 goes to chain-brake-switch terminal 1; chain-brake-switch terminal 2 returns toward the stator; trigger-switch right-hand terminal 1 goes separately toward the stator. Breaker terminal 2 and chain-brake-switch terminal 3 have no external lead drawn. This describes the source figure, not authorization to leave terminals disconnected on a different physical version. The two brush-holder connections are illustrated, but the stator leads have no terminal identifiers; no internal winding netlist, contact-state truth table, live continuity test or complete retrofit procedure is inferred.
  • After a trip, the TI says to pull the guide bar out of the cut, wait for the breaker to cool, disengage the chain brake if necessary, and press the breaker button fully to its stop. The brake step explicitly delegates to the owner’s manual chapter Chain Brake. That exact E140 owner-manual chapter was not found in the bounded local search; its edition is not identified by the TI. This is a documented source gap, not permission to substitute an E180C, later MSE or workshop-manual procedure.
  • If switching on does not start the motor, the TI says insufficient breaker cooling can be assumed: wait longer and press the button fully again. Retain this as the source’s stated scenario, not an exhaustive diagnosis of all electrical faults or an instruction for endless restart attempts. The source gives no fixed cooling interval.
  • As soon as the saw runs, the source calls for about 15 seconds off-load to cool the motor windings and prevent another trip. The 15 seconds is the off-load running period, not the breaker waiting interval. No saw was energized, drilled, rewired or tested; operator/manual requirements remain applicable.
  • TI02/1997 is a footer chronology pointer, not a delegated repair instruction. Both complete original pages, the drilling and wiring drawings, all summary rows, remarks and quiet regions are dispositioned. The local E140/E160/E180 workshop manual RA_100_00_01_02.pdf has a 2003-01 cover and a Chain Brake removal/installation chapter; it is not the delegated owner’s manual. No brake-operating directions have been invented from that chapter title. TI33 is reviewed with this named source gap, not a verified retrofit or exhaustive electrical diagnosis.

Source: TI 33/1999, p. 1 · TI 33/1999, p. 2 — Complete pages 1–2, including original wiring-terminal labels; delegated E140 owner-manual Chain Brake chapter unavailable in bounded local source search.

Part numbers (6)
  • 1208 430 1500 — Overload circuit breaker, 120 V, 1400 WNew in E 140 summary · E 140; stated 120 V, 1400 W version only
  • 1208 790 1011 — Handle housingPrevious E 140-only housing; deleted · E 140 before stated modification
  • 1208 790 1015 — Handle housingNew for E 140; already available for E 180 C · E 140 change; E 180 C is a pre-existing-use comparison
  • 1206 435 8000 — Packing ringAdded for E 140; already available for E 180 C · E 140 modification
  • 1208 440 1900 — WirePrevious wire deleted; no new number in table · E 140; not a direction to omit required circuit wiring
  • 1208 440 1905 — WirePrevious wire deleted; no new number in table · E 140; not a direction to omit required circuit wiring

Wrong number or missing part for the E 140, E 160, E 180 C? Report a correction →