Stihl 4116 · Section F · 6 of 12 · 33 parts
Air filter, Shroud
Fits FS 360, FS 420, FS 420 L.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (33)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 123 7500 | Grommet | 1 |
| 2 | 4116 182 9501 | Choke knob | 1 |
| 3 | 4116 141 1102 | Insert | 1 |
| 4 | 4116 120 1602 | Air filter | 1 |
| 5 | 4116 141 0300 | Auxiliary filter | 1 |
| 6 | 4116 149 0500 | Gasket | 1 |
| 7 | 4116 140 1901 | Carburetor box cover | 1 |
| 8 | 4116 141 8303 | Slotted nut | 2 |
| 9 | 4116 080 1604 | Shroud Fitment / change note → | 1 |
| 10 | 9416 868 5630 | Hollow rivet 5.5x0.5x6.8 | 4 |
| 11 | 4116 967 1503 | Model plate FS 360 Fitment / change note → | 1 |
| 12 | 4116 967 1504 | Model plate FS 420 Fitment / change note → | 1 |
| 13 | 9286 620 9810 | Flat nut 4.2 Fitment / change note → | 4 |
| 14 | 4116 080 1606 | Exhaust deflector Fitment / change note → | 1 |
| 15 | 9100 021 3280 | Self-tapping screw 4.2x14 Fitment / change note → | 1 |
| 16 | 9291 021 0100 | Washer 4.3 Fitment / change note → | 1 |
| 17 | 4116 141 2600 | Bow Fitment / change note → | 1 |
| 18 | 9307 021 0100 | Washer 4.3 Fitment / change note → | 1 |
| 19 | 4116 141 1800 | Sleeve Fitment / change note → | 1 |
| 20 | 9022 341 1070 | Spline screw IS-M5x30 Fitment / change note → | 1 |
| 21 | 9022 313 0680 | Spline screw IS-M4x16 | 3 |
| 22 | 9022 313 0740 | Spline screw IS-M4x25 | 1 |
| 23 | 4116 140 7101 | Protecting shroud | 1 |
| 24 | 9416 868 6630 | Hollow rivet 6.5x0.5x6.8 | 2 |
| 25 | 9100 021 3280 | Self-tapping screw 4.2x14 Fitment / change note → | 3 |
| 26 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 27 | 4116 141 1700 | Filter plate Fitment / change note → option | 1 |
| 41 | 4116 084 6600 | Threaded insert | 1 |
| 42 | 4116 967 1501 | Model plate FS 360 Fitment / change note → | 1 |
| 43 | 4116 967 1502 | Model plate FS 420 Fitment / change note → | 1 |
| 44 | 0000 974 1000 | Round head rivet 3x6 Fitment / change note → | 2 |
| 45 | 4119 140 9500 | Nut | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4116 007 1017 | Wire guard kit Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 360 / FS 420
FS 360 / 420: longer screen screws also fit older machines
14 mm BZ screws replace 9.5 mm screws at the screen-to-shroud joint.
- Screen-to-shroud connection changes from BZ 4.2×9.5 self-tapping screw 9100 021 0810 to BZ 4.2×14 screw 9100 021 3280. Source gives lengths 9.5 mm (0.37 in) and 14 mm (0.55 in), and explicitly permits the LONGER screws on OLDER machines.
- Original shorter screw remains available as a spare. Introduction in progress, no serial, torque or use at other joints specified. The source permission is limited to this screen/shroud connection.
- Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 18/1994, p. 5 — FS 360 / 420: longer screen screws also fit older machines.
Part numbers (2)
- 9100 021 0810 — BZ 4.2×9.5 screen screwretained spare · FS 360 / 420: longer screen screws also fit older machines
- 9100 021 3280 — BZ 4.2×14 screen screwalso permitted on older machines · FS 360 / 420: longer screen screws also fit older machines
Service note · FS 360 / FS 420
FS 360 / 420: oil-impregnated filter mat replaces the auxiliary filter
Optional bonded two-layer foam mat is for extremely dusty conditions.
- Special-accessory filter mat 4116 141 1700 has been available for some time for extremely dusty conditions. Fine-pored and coarse-pored foam sheets are BONDED together and oil impregnated to retain extra-fine dust. Install IN PLACE OF the standard auxiliary filter, not as an additional unspecified layer.
- Each mat comes with illustrated installation and cleaning instructions. Those separate instructions are referenced, not reproduced or reviewed here; this page supplies no cleaning solvent, oil dose or layer orientation. Drawing confirms shaped mat, not a dimensional template. Last-TI pointer 49.92 is a reference, not acceptance of that source or a complete service manual. Original footer is May 2, 1994.
- Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 18/1994, p. 6 — FS 360 / 420: oil-impregnated filter mat replaces the auxiliary filter.
Part numbers (1)
- 4116 141 1700 — Oil-impregnated bonded foam filter matoptional auxiliary-filter replacement · FS 360 / 420: oil-impregnated filter mat replaces the auxiliary filter
Service note · FS 360 / FS 420
FS 360 / FS 420: spark plug terminal requires its new cover
The new terminal may only be used with the new cover; initial changeover uses the complete kit.
X 30 629 622 — FS 360 / FS 420 terminal/cover change only.
- From X 30 629 622, old cover-shaped terminal 4116 405 1000 is replaced by terminal 1106 405 1000 and a separate cover. Terminal 1106 405 1000 CAN ONLY BE USED TOGETHER WITH THE NEW COVER. Initial changeover kit 4116 400 7150 includes keys 1–3: cover, mounting screw and terminal; MOQ 1.
- Cover (key 1) has NO separate number and is NOT AVAILABLE SEPARATELY. Screw 9025 313 0741 is IS/slotted M4x25x10, key 2, MOQ 10; terminal 1106 405 1000 is key 3, MOQ 1. The prose calls the fastener M4x25; do not discard the table suffix or invent a torque. The threaded insert is integrally molded into the shroud and is not separately available according to this TI.
- Leg spring 0000 998 0603 (key 4) is unchanged. Old cable clamp 4116 431 2500 (key 5), B3.9x16 screw 9099 021 2790 (key 6), IS M4x16 screw 4116 404 7800 (key 7) remain available as spares despite dashes in the new column. Old terminal lasts only while factory stocks remain. Blank MOQ cells remain unknown, not zero.
- Figure 340TI002 shows old and new cover/terminal arrangements; it is not authority to fit the new terminal bare. The later shroud IPL lists a threaded insert 4116 084 6600, but this TI gives no insert number: exact identity with the molded insert is UNESTABLISHED. Preserve the historical non-separate-supply statement without treating the later row as proof of a safe retrofit.
- Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.
Source: TI 48/1994, p. 3 · TI 48/1994, p. 4 — spark plug terminal requires its new cover.
Part numbers (8)
- 4116 405 1000 — Original cover-shaped terminalwhile stocks last · FS 360 / FS 420 only in the configuration described here
- 4116 400 7150 — Initial terminal changeover kitincludes 1–3; MOQ 1 · FS 360 / FS 420 only in the configuration described here
- 9025 313 0741 — IS/slotted M4x25x10 screw; key 2MOQ 10 · FS 360 / FS 420 only in the configuration described here
- 1106 405 1000 — Spark plug terminal; key 3MOQ 1; new cover required · FS 360 / FS 420 only in the configuration described here
- 0000 998 0603 — Leg spring; key 4unchanged · FS 360 / FS 420 only in the configuration described here
- 4116 431 2500 — Original cable clamp; key 5remains available as spare · FS 360 / FS 420 only in the configuration described here
- 9099 021 2790 — Original B3.9x16 screw; key 6remains available as spare · FS 360 / FS 420 only in the configuration described here
- 4116 404 7800 — Original IS M4x16 screw; key 7remains available as spare · FS 360 / FS 420 only in the configuration described here
Service note · FS 360 / FS 420
FS 360 / FS 420 wire bracket: spark-screen versions and delivery mounting
Loose bracket must be mounted before handover; preserve two washers and spacer.
X 31 942 303 — FS 360 / FS 420 spark-arresting-screen versions; production wire bracket introduction, not a prohibition on older-machine retrofit.
- From machine number X 31 942 303, FS 360 and FS 420 VERSIONS WITH SPARK ARRESTING SCREEN IN MUFFLER receive wire bracket 4116 141 2600. This is not every exhaust version, FS 420 L or all series 4116 machines.
- The bracket attaches with ONE SCREW at the exhaust deflector and ONE at the starter cover. Deflector 4116 080 1606 has a provided hole. Hardware is fitted at the factory, but the bracket itself is supplied LOOSE for packaging and MUST BE FITTED BEFORE HANDOVER to the customer; factory supply does not mean the delivered bracket is already installed.
- Remove self-tapping screw (1) from deflector WITHOUT LOSING THE TWO WASHERS; remove spline screw (2) from starter cover; position bracket (3), preserving washer positions and spacer sleeve (4); refit both screws and tighten firmly. No numeric torque is specified.
- Figure 340TI 003 shows the two washers on opposite sides of the upper bracket eye and the spacer between the lower eye and starter cover. Figure callouts 1/2/3/4 are mounting identifiers, NOT the summary-table keys on page 2.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 24/1995, p. 1 · TI 24/1995, p. 2 — Production scope and mounting, figure 340TI003.
Part numbers (2)
- 4116 141 2600 — Wire bracketnew; spark-screen versions · FS 360 / FS 420; Production scope and mounting, figure 340TI 003
- 4116 080 1606 — Exhaust deflectormodified with mounting hole; same number · FS 360 / FS 420; Production scope and mounting, figure 340TI 003
Service note · FS 360 / FS 420
FS 360 / FS 420 wire bracket retrofit: drill the shroud, not the deflector
Kit includes items 1–8 and instructions; 4.2-mm hole and flat-side-up nut.
- Wire bracket mounting kit 4116 007 1017 is available for OLDER MACHINES in this TI scope. It includes modified exhaust deflector, bracket, mounting hardware (summary items 1–8) and fitting instructions. The supplied leaflet is not reproduced here; the TI itself supplies mounting/preparation guidance. No unprinted leaflet step is claimed.
- Hold the exhaust deflector in its installed position against the SHROUD and mark the hole. TAKE AWAY THE DEFLECTOR, then drill a 4.2-mm-diameter hole IN THE SHROUD. This is not an instruction to drill a second hole in the already modified deflector.
- Push sheet-metal nut B4.2, 9286 620 9810, onto the shroud over the hole with FLAT SIDE UP. Figure 340TI 004 identifies key 6 screw, key 7 washer, key 2 bracket, key 8 washer, key 1 deflector and key 3 nut in the upper stack; key 4 sleeve and key 5 spline screw are at the other attachment.
- No hole-edge coordinates or numeric tightening torque are supplied; installed-position marking and the original figure are the location guidance. The production cutoff is not a lower eligibility limit for this older-machine kit.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 24/1995, p. 2 — Service note, preparations and figure 340TI004.
Part numbers (2)
- 4116 007 1017 — Wire bracket mounting kitincludes items 1–8 and instructions; MOQ 1 · FS 360 / FS 420; Service note, preparations and figure 340TI 004
- 9286 620 9810 — Sheet metal nut B4.2key 3; flat side up; MOQ 10 · FS 360 / FS 420; Service note, preparations and figure 340TI 004
Service note · FS 360 / FS 420
FS 360 / FS 420 wire bracket parts: same-number deflector and distinct washers
Nut quantity rises from three to four per machine; order minima are not installed counts.
- Exhaust deflector 4116 080 1606 is printed as BOTH ORIGINAL AND NEW, key 1, MOQ 1. Only its MODIFIED VERSION is factory available (remark 1); a part-number-only lookup cannot distinguish drilled and original geometry. All other parts as before.
- Wire bracket 4116 141 2600 key 2 MOQ 1; spacer sleeve 4116 141 1800 key 4 MOQ 1; spline screw IS M5x30x22 9022 341 1070 key 5 MOQ 10; self-tapping screw BZ4.2x14 9100 021 3280 key 6 MOQ 10. The new-part dashes are not part numbers.
- Two DISTINCT Washer A4.3 numbers: 9291 021 0100 key 7 and 9307 021 0100 key 8, each MOQ 10. Same nominal designation does not establish interchangeability or permit omitting either washer.
- Sheet metal nut 9286 620 9810 key 3 MOQ 10 has remark 2: quantity PER MACHINE increases from THREE TO FOUR. This is not four nuts at the bracket attachment, four nuts in the kit or ten installed nuts.
- Later exact FS 360/420 F sheet lists the kit without a position; deflector key 14; screw 15; washer 16; bracket 17; washer 18; sleeve 19; spline screw 20; nut 13 qty 4. Its M5x30 label omits the TI x22 suffix; retain the full historical designation without inventing a new screw revision. Shared FS 420 L labeling does not expand source scope.
- Footer April 6, 1995, D1/MTK-sc; last TI 48/1994 is bibliographic. TI 25/1995 page 3 separately says TI 24 was issued only in specific sales territories, not all countries; it names no complete territory list. Do not infer universal market coverage.
- Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.
Source: TI 24/1995, p. 2 — Complete summary, both remarks and footer.
Part numbers (8)
- 4116 080 1606 — Exhaust deflectorkey 1; unchanged number; modified-only supply; MOQ 1 · FS 360 / FS 420; Complete summary, both remarks and footer
- 4116 141 2600 — Wire bracketkey 2; MOQ 1 · FS 360 / FS 420; Complete summary, both remarks and footer
- 9286 620 9810 — Sheet metal nut B4.2key 3; machine quantity 3 to 4; MOQ 10 · FS 360 / FS 420; Complete summary, both remarks and footer
- 4116 141 1800 — Spacer sleevekey 4; MOQ 1 · FS 360 / FS 420; Complete summary, both remarks and footer
- 9022 341 1070 — Spline screw IS M5x30x22key 5; MOQ 10 · FS 360 / FS 420; Complete summary, both remarks and footer
- 9100 021 3280 — Self-tapping screw BZ4.2x14key 6; MOQ 10 · FS 360 / FS 420; Complete summary, both remarks and footer
- 9291 021 0100 — Washer A4.3key 7; above bracket; MOQ 10 · FS 360 / FS 420; Complete summary, both remarks and footer
- 9307 021 0100 — Washer A4.3key 8; below bracket; MOQ 10 · FS 360 / FS 420; Complete summary, both remarks and footer
Historical fitment · FS 360
FS 360: clip-in plastic nameplate requires countersunk shroud
4116 967 1501 → 4116 967 1503; old aluminium plate and 3 x 6 rivet retained for old shrouds.
X 32 196 669 — Section 3 printed nameplate changeover; FS 360 nameplate only, not starter or cap.
- Section 3 replaces riveted aluminium nameplates with clip-in plastic nameplates from printed machine number X 32 196 669. This is separate from the FS 360 starter X 32 701 029 and cap X 32 195 173 changes. The plastic plate is pushed into the shroud and retained by TWO retaining lugs; the two mounting holes in the new shroud are countersunk.
- Plastic nameplates CANNOT be fitted to the original shroud because it lacks countersunk mounting holes. This is not a drill/countersink conversion instruction; no dimensions, tool, angle or modified old-shroud procedure is supplied. No shroud part number is printed.
- The FS 360 table row changes aluminium nameplate 4116 967 1501 to plastic nameplate 4116 967 1503. Original aluminium plates and round head rivets 0000 974 1000 (3 x 6) remain available for older machines. The dash in the new rivet column does not mean old repair rivets are discontinued. No rivet quantity is specified.
- The FS 360 row agrees with the bulletin header. The separate FS 420 row is retained in its own note and does not broaden the FS 360 starter/cap scope.
- Historical TI 09/1996 evidence, not verified physical interchange or current stock. No hardware operation was performed. FS 420 L and other shared-sheet models are excluded. Last-TI 48/1994, imprint and blank space provide no additional fitment; the self-contained nameplate restriction does not depend on that bibliography.
Source: TI 9/1996, p. 3 — FS 360: clip-in plastic nameplate requires countersunk shroud.
Part numbers (3)
- 4116 967 1501 — FS 360 original aluminium nameplateretained for older machines · FS 360 original shroud
- 4116 967 1503 — FS 360 plastic nameplatenew; requires countersunk mounting holes · FS 360 modified shroud only
- 0000 974 1000 — Round head rivet 3 x 6retained for original aluminium nameplate; quantity unspecified · FS 360 original shroud
Historical fitment · FS 420
FS 420: clip-in plastic nameplate requires countersunk shroud
4116 967 1502 → 4116 967 1504; old aluminium plate and 3 x 6 rivet retained for old shrouds.
X 32 196 669 — Section 3 printed nameplate changeover; FS 420 appears in table despite FS 360-only header, so independent FS 420 production applicability remains unverified.
- Section 3 replaces riveted aluminium nameplates with clip-in plastic nameplates from printed machine number X 32 196 669. This is separate from the FS 360 starter X 32 701 029 and cap X 32 195 173 changes. The plastic plate is pushed into the shroud and retained by TWO retaining lugs; the two mounting holes in the new shroud are countersunk.
- Plastic nameplates CANNOT be fitted to the original shroud because it lacks countersunk mounting holes. This is not a drill/countersink conversion instruction; no dimensions, tool, angle or modified old-shroud procedure is supplied. No shroud part number is printed.
- The FS 420 table row changes aluminium nameplate 4116 967 1502 to plastic nameplate 4116 967 1504. Original aluminium plates and round head rivets 0000 974 1000 (3 x 6) remain available for older machines. The dash in the new rivet column does not mean old repair rivets are discontinued. No rivet quantity is specified.
- The bulletin header names FS 360 only, and section 3 explicitly lists FS 420 as well. This note admits the exact FS 420 nameplate row and its section-level printed boundary, while preserving the header/table scope difference. It does not establish FS 420 ElastoStart or cap changes, nor independently verify an FS 420 production cutoff.
- Historical TI 09/1996 evidence, not verified physical interchange or current stock. No hardware operation was performed. FS 420 L and other shared-sheet models are excluded. Last-TI 48/1994, imprint and blank space provide no additional fitment; the self-contained nameplate restriction does not depend on that bibliography.
Source: TI 9/1996, p. 3 — FS 420: clip-in plastic nameplate requires countersunk shroud.
Part numbers (3)
- 4116 967 1502 — FS 420 original aluminium nameplateretained for older machines · FS 420 original shroud
- 4116 967 1504 — FS 420 plastic nameplatenew; requires countersunk mounting holes · FS 420 modified shroud only
- 0000 974 1000 — Round head rivet 3 x 6retained for original aluminium nameplate; quantity unspecified · FS 420 original shroud
Service note · FS 550 / FS 360 / FS 420
FS 550: shroud and drive-tube assembly inclusions
Drive tube includes plug and warning label; the FS 550 nameplate is separate.
- Drive tube item 20 INCLUDES plug 21 and warning label 22. Nameplate 19 is specifically FS 550; it is not listed as included with the shroud. No drive-tube length is printed in this table.
- Remark 1 identifies shroud 18 and drive tube 20 as predecessor FS 360/FS 420 spares too. It does not separately mark nameplate 19, plug 21 or warning label 22. Keep assembly inclusion distinct from a blanket predecessor-fitment claim for each component.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 10 — Section7 rows18–22 and remark1.
Part numbers (5)
- 4116 080 1604 — Item18 shroud; remark1Exact section7 row · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 967 1506 — Item19 FS550 nameplateExact section7 row · FS 550 table context; no separate predecessor remark on this row
- 4116 710 7145 — Item20 FS550 drive tube including21/22; remark1Exact section7 row · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 711 2100 — Item21 plugExact section7 row · FS 550 table context; no separate predecessor remark on this row
- 0000 967 3684 — Item22 warning labelExact section7 row · FS 550 table context; no separate predecessor remark on this row
Wrong number or missing part for the FS 360, FS 420, FS 420 L? Report a correction →