← FS 360, FS 420, FS 420 L · FS 500, FS 550, FS 550 L

Stihl 4116 · Section G · 7 of 12 · 37 parts

Drive tube assembly, Clutch housing

Fits FS 360, FS 420, FS 420 L.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131314151617181922021212223242526272829330313233343536374556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (37)

PosPart numberDescriptionQty
1 4116 710 7149 Drive tube assembly Ø 35 mm / 1 3/8'' 1
2 4116 710 7150 Drive tube assembly Ø 35 mm / 1 3/8'' 1
3 4116 710 7145 Drive tube assembly Ø 35 mm / 1 3/8'' Fitment / change note → 1
4 4116 711 7300 Flexible liner Fitment / change note → 1
5 4116 711 2100 Plug Fitment / change note → 2
6 0000 967 3725 Warning pictogram FS 1
7 4116 711 7301 Flexible liner Fitment / change note → 1
8 0000 967 3684 Warning pictogram FS Fitment / change note → 1
9 4116 711 3212 Drive shaft Fitment / change note → 1
10 4116 711 3211 Drive shaft Fitment / change note → 1
11 4116 791 1003 AV housing, top Fitment / change note → 1
12 4116 716 2901 Perforated strip 1
13 9022 341 1010 Spline screw IS-M5x18 4
14 9451 621 2940 Shakeproof washer 26x0.5 1
15 0000 955 0801 Hexagon nut M8 1
16 4116 791 2810 Stop buffer 1
17 4116 791 2801 Annular buffer Fitment / change note → 2
18 4116 791 7300 Plug 2
19 4116 791 1008 AV housing, bottom Fitment / change note → 1
20 4116 791 2805 Stop buffer 1
21 9022 341 0900 Spline screw IS-M5x28 7
22 4116 791 6803 Clamp, right 1
23 4116 791 6802 Clamp, left 1
24 4116 161 0501 Clutch housing Fitment / change note → 1
25 9456 621 3860 Circlip 35x1.5 1
26 9503 003 7450 Grooved ball bearing 6202-2RS 1
27 9455 621 1520 Circlip 15x1 1
28 0000 958 2506 Washer 1
29 9456 621 3320 Circlip 30x1.5 Fitment / change note → 2
30 9022 341 1350 Spline screw IS-M6x25 1
31 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 1
32 4116 790 9900 Annular buffer Fitment / change note → 2
33 1125 791 7306 Plug 2
34 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 6
35 4116 700 8400 Support 1
36 9416 868 6630 Hollow rivet 6.5x0.5x6.8 2
37 4116 791 0500 Cover strip 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 420 L

FS 420 L: longer shaft has its own tube and liner

The L version adds 120 mm of shaft reach; standard FS 360 / 420 shaft numbers are separate.

  • New FS 420 L is described as immediately available for cutting applications requiring extra reach, such as mowing from the base of embankments and ditches. Its drive shaft is 120 mm (4.7 in) LONGER than previous versions; this is an increase, not the total shaft length or a retrofit authorization.
  • FS 420 L drive tube 4116 710 7130 includes flexible polymer liner 4116 711 7301 (1), TWO 30×1.5 circlips 9456 621 3320 (2), and plug 4119 711 2100 (3). Separate long drive shaft is 4116 711 3211. Do not substitute standard-model shaft 4116 711 3212 or liner 4116 711 7300 merely because they appear on the next page.
  • Page 1 refers to chapter 2 for liner construction: liner is replaceable and retained by a circlip at each end. Looking FROM THE GEAR HEAD END, fins must point COUNTERCLOCKWISE to prevent co-rotation. Push liner in FROM THE GEAR HEAD END until circlips fit grooves at BOTH ends. Thoroughly grease the entire shaft with STIHL multipurpose grease 0781 120 1109, rotating shaft while sliding it in. No dimensional or cutoff inference for a long-version conversion is made.
  • Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 18/1994, p. 1 · TI 18/1994, p. 2 — FS 420 L: longer shaft has its own tube and liner.

Part numbers (6)
  • 4116 710 7130 — FS 420 L drive tube, items 1–3long version · FS 420 L: longer shaft has its own tube and liner
  • 4116 711 7301 — FS 420 L flexible liner, item 1long version · FS 420 L: longer shaft has its own tube and liner
  • 9456 621 3320 — 30×1.5 circlip, item 2two fitted · FS 420 L: longer shaft has its own tube and liner
  • 4119 711 2100 — Plug, item 3included · FS 420 L: longer shaft has its own tube and liner
  • 4116 711 3211 — FS 420 L drive shaft120 mm longer · FS 420 L: longer shaft has its own tube and liner
  • 0781 120 1109 — STIHL multipurpose greaseliner service procedure · FS 420 L: longer shaft has its own tube and liner

Service note · FS 360 / FS 420

FS 360 / 420: original drive tubes require the original shaft

Polymer-liner tubes and new shaft do not establish unrestricted old-tube interchange.

  • Flexible polymer liner replaces five rubber-mounted bushes, is replaceable when worn, and is located axially by a circlip at EACH end. Original shaft was hardened at the five bearing areas. Production changes to shaft 4116 711 3212; ONLY shaft 4116 711 3200 may be installed in ORIGINAL drive tubes.
  • Looking FROM THE GEAR HEAD END, liner fins must point COUNTERCLOCKWISE as the diagram shows, preventing liner rotation with the shaft. Push liner FROM THE GEAR HEAD END until circlips can be fitted in grooves at BOTH ends. Thoroughly coat ENTIRE shaft with STIHL multipurpose grease 0781 120 1109 before sliding it in while rotating it. Do not replace this circlip-based position rule with another model's flush-end instruction.
  • Tube 4116 710 7125 changes to 4116 710 7140, including liner 4116 711 7300 (1), TWO 30×1.5 circlips 9456 621 3320 (2), and unchanged plug 4119 711 2100 (3). Original tube remains supplied only while stocks last; original shaft REMAINS available for older machines. Prose saying original shaft is discontinued describes the production change and does not erase the explicit retained-spares footnote. Introduction in progress, no serial supplied.
  • Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 18/1994, p. 2 — FS 360 / 420: original drive tubes require the original shaft.

Part numbers (8)
  • 4116 710 7125 — Original FS 360 / 420 drive tubewhile stocks last · FS 360 / 420: original drive tubes require the original shaft
  • 4116 710 7140 — Polymer-liner drive tube, items 1–3new · FS 360 / 420: original drive tubes require the original shaft
  • 4116 711 7300 — Flexible liner, item 1standard length · FS 360 / 420: original drive tubes require the original shaft
  • 9456 621 3320 — 30×1.5 circlip, item 2two fitted · FS 360 / 420: original drive tubes require the original shaft
  • 4119 711 2100 — Plug, item 3unchanged · FS 360 / 420: original drive tubes require the original shaft
  • 4116 711 3200 — Original drive shaftmandatory in original tubes; retained spare · FS 360 / 420: original drive tubes require the original shaft
  • 4116 711 3212 — New drive shaftnew liner-tube application · FS 360 / 420: original drive tubes require the original shaft
  • 0781 120 1109 — STIHL multipurpose greasecoat entire shaft · FS 360 / 420: original drive tubes require the original shaft

Service note · FS 360 / FS 420

FS 360 / 420: new clutch housing omits rubber rings and clamp spacer

Earlier housing remains while stocks last; rings and spacer remain for older machines.

  • Housing 4116 161 0501, formerly used in a few special versions, becomes standard on FS 360 and FS 420 WITHOUT rubber rings and WITHOUT spacer in the clamp. Source says this improves drive-tube security and AV resistance to sudden loads such as brush-knife use.
  • Original housing 4116 160 0600 (item 1) remains factory-supplied only until stocks are exhausted. TWO rubber rings 4116 791 9600 (item 2) and spacer 4116 162 9800 (item 3) remain available for OLDER machines. The exploded diagram identifies removed pieces; this is not permission to delete them from an unchanged old housing. All other parts as before; introduction in progress, no serial.
  • Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 18/1994, p. 3 · TI 18/1994, p. 4 — FS 360 / 420: new clutch housing omits rubber rings and clamp spacer.

Part numbers (4)
  • 4116 160 0600 — Original clutch housing, item 1while stocks last · FS 360 / 420: new clutch housing omits rubber rings and clamp spacer
  • 4116 161 0501 — New clutch housing, item 1without rings/spacer · FS 360 / 420: new clutch housing omits rubber rings and clamp spacer
  • 4116 791 9600 — Rubber ring, item 2, two fitted originallyretained for older machines · FS 360 / 420: new clutch housing omits rubber rings and clamp spacer
  • 4116 162 9800 — Clamp spacer, item 3retained for older machines · FS 360 / 420: new clutch housing omits rubber rings and clamp spacer

Service note · FS 360 / FS 420

FS 360 / 420: unlined clutch requires the smaller matching drum

Old and new clutch versions cannot be mixed; complete replacement assembly preserves pairing.

X 29 624 487 — Printed introduction for this component only; not a universal machine cutoff or interchange guarantee.

  • From X 29 624 487, clutch 4116 160 2002 has shoes WITHOUT linings and a new drum with inside diameter 74 mm (2.9 in) instead of 78 mm (3.1 in). These are DRUM INSIDE diameters, not shoe or shaft dimensions.
  • Parts of original and new clutch versions CANNOT be combined. Complete clutch-with-drum assembly 4116 160 2050 (items 1–4) is supplied to replace old drum 4116 160 2900, which is no longer factory-available. Original clutch 4116 160 2001 remains a spare only UP TO THE END OF 1998; after that date use BOTH new clutch and new drum.
  • New clutch item 1 includes unchanged spring 0000 997 1703 (2) and ring 0000 961 0802 (3). New drum item 4 has no separate part number printed (-*- is not an order number) and is NOT separately available up to the end of 1998. That historical qualification does not establish later separate availability or an invented drum number. Retain both distinct 1998 limits.
  • Historical TI 18/1994 guidance for explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 18/1994, p. 4 — FS 360 / 420: unlined clutch requires the smaller matching drum.

Part numbers (6)
  • 4116 160 2050 — Clutch with clutch drum, items 1–4complete paired replacement · FS 360 / 420: unlined clutch requires the smaller matching drum
  • 4116 160 2001 — Original lined clutchspare up to end of 1998 · FS 360 / 420: unlined clutch requires the smaller matching drum
  • 4116 160 2002 — Unlined clutch, item 1use matching new drum · FS 360 / 420: unlined clutch requires the smaller matching drum
  • 0000 997 1703 — Clutch spring, item 2unchanged · FS 360 / 420: unlined clutch requires the smaller matching drum
  • 0000 961 0802 — Ring, item 3unchanged · FS 360 / 420: unlined clutch requires the smaller matching drum
  • 4116 160 2900 — Original clutch drum, item 4no longer factory-available · FS 360 / 420: unlined clutch requires the smaller matching drum

Service note · FS 360 / FS 420

FS 360 / FS 420: softer buffers require matched AV housings

From X 37 266 391, do not mix old and new housing components; new AV buffers require the new housing.

X 37 266 391 — Introduction of modified AV system on FS 360 and FS 420; printed prefix retained.

  • TI29/1997 introduces SOFTER annular buffers in both clutch housing and AV housing from machine number X 37 266 391, with an enlarged gap between the AV and clutch housings. Preserve the printed X prefix; no automatic serial-range matcher or country decoding is established.
  • DO NOT COMBINE COMPONENT PARTS OF THE ORIGINAL AND NEW AV HOUSINGS. New item 2 buffers 4116 791 2801 MAY ONLY BE INSTALLED IN THE NEW VERSION OF THE AV HOUSING, otherwise housing parts may rub and wear. The source does not authorize a mixed top/bottom housing or extrapolate reverse interchange.
  • Drawing 340TI009 SC shows TWO occurrences of item 1 at the clutch housing and TWO of item 2 at the AV housing ends, plus top 3 and bottom 4. The summary separately specifies TWO of EACH buffer type; do not merge the two pairs or confuse these callouts with later IPL positions 32 and 17.
  • Summary item 1: 1125 790 9921 → 4116 790 9900; old version no longer factory-available (remark 1). Item 2: 4116 791 2800 → 4116 791 2801; old version remains an older-machine spare (remark 2). Top 4116 790 0900 → 4116 791 1003 and bottom 4116 791 1007 → 4116 791 1008 retain originals only until factory stocks run out (remark 3). ALL OTHER PARTS AS BEFORE.
  • The exact FS 360/FS 420 sheet retains all four new numbers. Its shared FS 420 L heading, and the same parts on FS 500/550 sheets, do not extend this bulletin to those models. Footer TI30.96 and TI27.97 USA-only are bibliographic context, not delegated service procedures; footer/document 6114 and blank areas add no fitment claim.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 29/1997, p. 1 — Complete page: introduction, both service prohibitions, drawing, all four summary rows, remarks and footer.

Part numbers (8)
  • 1125 790 9921 — Original clutch-housing annular buffer, twoNo longer available from factory · Only the exact model/configuration and restrictions of 1997-29
  • 4116 790 9900 — New clutch-housing annular buffer, twoSofter replacement; item 1 · Only the exact model/configuration and restrictions of 1997-29
  • 4116 791 2800 — Original AV-housing annular buffer, twoRetained for older machines · Only the exact model/configuration and restrictions of 1997-29
  • 4116 791 2801 — New AV-housing annular buffer, twoNew housing only; item 2 · Only the exact model/configuration and restrictions of 1997-29
  • 4116 790 0900 — Original AV housing topStock exhaustion · Only the exact model/configuration and restrictions of 1997-29
  • 4116 791 1003 — New AV housing topItem 3 · Only the exact model/configuration and restrictions of 1997-29
  • 4116 791 1007 — Original AV housing bottomStock exhaustion · Only the exact model/configuration and restrictions of 1997-29
  • 4116 791 1008 — New AV housing bottomItem 4 · Only the exact model/configuration and restrictions of 1997-29

Service note · FS 550 / FS 360 / FS 420

FS 550: shroud and drive-tube assembly inclusions

Drive tube includes plug and warning label; the FS 550 nameplate is separate.

  • Drive tube item 20 INCLUDES plug 21 and warning label 22. Nameplate 19 is specifically FS 550; it is not listed as included with the shroud. No drive-tube length is printed in this table.
  • Remark 1 identifies shroud 18 and drive tube 20 as predecessor FS 360/FS 420 spares too. It does not separately mark nameplate 19, plug 21 or warning label 22. Keep assembly inclusion distinct from a blanket predecessor-fitment claim for each component.
  • Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.

Source: TI 44/1997, p. 10 — Section7 rows18–22 and remark1.

Part numbers (5)
  • 4116 080 1604 — Item18 shroud; remark1Exact section7 row · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
  • 4116 967 1506 — Item19 FS550 nameplateExact section7 row · FS 550 table context; no separate predecessor remark on this row
  • 4116 710 7145 — Item20 FS550 drive tube including21/22; remark1Exact section7 row · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
  • 4116 711 2100 — Item21 plugExact section7 row · FS 550 table context; no separate predecessor remark on this row
  • 0000 967 3684 — Item22 warning labelExact section7 row · FS 550 table context; no separate predecessor remark on this row

Conditional replacement · FS 550 / FS 360 / FS 420

FS 550: paired AV buffers and Scandinavia-only option

Use identical buffers in pairs; predecessor AV parts have an explicit serial limit.

  • Contrary to the parts-list illustration, buffer 4116 791 2800 is installed at the FRONT of the AV housing. Optional 4116 791 2801 is for SCANDINAVIA ONLY. Always use buffers of IDENTICAL TYPE for repairs and ALWAYS REPLACE IN PAIRS. The printed word annual is a source typo for annular, not a maintenance interval.
  • Top housing 23 is 4116 791 1003; buffer 24 has standard 2800 and optional 2801 versions; bottom housing 25 is 4116 791 1008. All carry remark 2: also predecessor FS 360/FS 420 spares FROM machine No. X 37 266 391. Only optional 2801 additionally carries remark 3, Scandinavia only. Preserve X; do not decode a country or invent an upper limit.
  • TI 29/1997 is directly referenced and separately reviewed: its predecessor change introduces softer buffers and prohibits mixing original/new AV-housing components; new 2801 buffers require the new housing. TI 44 uses 2800 as the FS 550 default and restricts 2801 geographically. These are distinct model/region contexts, not universal 2800-to 2801 substitution or a reason to erase either statement.
  • Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.

Source: TI 44/1997, p. 10 — Section7 opening correction, rows23–25 including both24 options, remarks2/3 and TI29 reference.

Referenced bulletin evidence: TI 29/1997, p. 1 — Complete page: introduction, both service prohibitions, drawing, all four summary rows, remarks and footer.

Part numbers (4)
  • 4116 791 1003 — Item23 AV housing topPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
  • 4116 791 2800 — Item24 annular buffer; standardPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
  • 4116 791 2801 — Item24 annular buffer; Scandinavia onlyPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only
  • 4116 791 1008 — Item25 AV housing bottomPairs/type/region/serial restrictions apply · FS 550; remark2 also FS 360/FS 420 from X 37 266 391; paired identical buffers;2801 Scandinavia only

Wrong number or missing part for the FS 360, FS 420, FS 420 L? Report a correction →