Stihl 4116 · Section E · 5 of 16 · 41 parts
Carburetor HD-31, HD-22
Fits FS 500, FS 550, FS 550 L.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (41)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 4116 122 3002 | Spring | 1 |
| 3 | 1113 121 9200 | Spindle | 1 |
| 4 | 4116 121 5000 | Inlet control lever | 1 |
| 5 | 1114 122 7400 | Round head screw | 1 |
| 6 | 4117 122 9402 | Plug | 1 |
| 7 | 4116 129 0901 | Gasket | 1 |
| 8 | 4116 121 4700 | Metering diaphragm | 1 |
| 9 | 4116 121 0800 | End cover | 1 |
| 10 | 1106 122 7400 | Round head screw | 4 |
| 11 | 1114 121 7800 | Strainer | 1 |
| 12 | 4116 121 4800 | Pump diaphragm | 1 |
| 13 | 4116 129 0902 | Gasket | 1 |
| 14 | 4116 120 0800 | End cover | 1 |
| 15 | 1114 122 7100 | Screw | 1 |
| 16 | 4117 122 3006 | Spring | 1 |
| 17 | 4117 122 6200 | Idle speed adjustment screw | 1 |
| 18 | 4116 120 7100 | Throttle shaft with lever | 1 |
| 19 | 4116 122 3200 | Torsion spring | 1 |
| 20 | 4116 121 3300 | Throttle shutter | 1 |
| 21 | 1115 122 7400 | Round head screw | 1 |
| 22 | 4116 122 5000 | Spacer sleeve | 1 |
| 23 | 4116 123 7301 | Lever | 1 |
| 24 | 1110 122 7400 | Round head screw | 2 |
| 25 | 4215 121 8600 | Washer | 1 |
| 26 | 4215 121 8900 | Pin | 1 |
| 27 | 1117 122 9000 | E-clip | 1 |
| 28 | 1116 122 3000 | Spring | 1 |
| 29 | 1116 122 4200 | Ball | 1 |
| 30 | 4116 121 3000 | Choke shaft | 1 |
| 31 | 4116 121 2901 | Choke shutter | 1 |
| 32 | 4116 121 5400 | Valve jet | 1 |
| 33 | 4203 122 6703 | High speed adjustment screw | 1 |
| 34 | 4203 122 3600 | Sealing ring | 1 |
| 35 | 4203 121 2700 | Cap Fitment / change note → | 2 |
| 36 | 1127 122 6800 | Low speed adjustment screw | 1 |
| 37 | 4203 122 6804 | Low speed adjustment screw | 1 |
| 38 | 5910 890 4500 | Puller Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4116 120 0606 | Carburetor HD-31 | 1 |
| — | 4116 120 0603 | Carburetor HD-22 Fitment / change note → | 1 |
| — | 4116 007 1061 | Set of carburetor parts Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BR 320 / BR 340 / BR 400 / BR 420 / SR 320 / SR 340 / SR 400 / SR 420 / FS 550
BR/SR blowers and FS 550: revised limiter cap keeps the same number
Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
Later reviewed guidance: BR/SR blowers and FS 550: square-bit driver for fitted limiter caps
- Limiter cap 4203 121 2700 and the carburetor retain their part numbers despite revised cap/segment geometry; number alone does not identify the old or new cap.
- The new cap has no upper detent, adds an alignment mark and moves the lug from perpendicular to the screw slot into line with it.
- These models appear on the bulletin cover but NOT in the marked-segment subset on pages 2–4. Do not infer marked-segment alignment from cover inclusion; the slot, groove and visible-lug checks remain distinct from the marks-only instruction.
- The marked-segment drawing and its dimensions must not be assigned to these models solely from the shared limiter-cap number.
- H and L removal have separate alignment instructions. Puller 5910 890 4500 has a left-hand engagement thread; this note is not a complete carburetor removal or calibration procedure.
- Removed limiter caps must not be reused because removal damages them. Replace caps after screw replacement or carburetor cleaning; no permanent cap-removal modification is implied.
- Applies only to the named models with limiter cap 4203 121 2700. A shared catalog sheet is not approval for its other models or C/L variants. The sheet may contain uncapped versions; verify the actual carburetor configuration.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 21/2005, p. 1 · TI 21/2005, p. 2 · TI 21/2005, p. 3 · TI 21/2005, p. 4 — Sections 1–5: named-model cap revision; cover list distinguished from marked-segment subset.
Part numbers (2)
- 4203 121 2700 — Limiter capUnchanged number, revised geometry · Named models using 4203 121 2700; single-use after removal
- 5910 890 4500 — Limiter-cap pullerService tool · Left-hand engagement; separate H/L alignment
Conditional replacement · BR 320 / BR 340 / BR 400 / BR 420 / SR 320 / SR 340 / SR 400 / SR 420 / FS 550
BR/SR blowers and FS 550: square-bit driver for fitted limiter caps
Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Screwdriver 5910 890 2304 is specified for carburetors using limiter cap 4203 121 2700; its square bit reaches the adjusting screw through the fitted cap.
- Conditional on limiter cap 4203 121 2700 actually being fitted, not every carburetor or every model/variant on the shared catalog sheet. Model association comes from TI 21/2005 and the catalog cap row; TI 50/2006 specifies the tool by cap configuration.
- The without-cap basic-setting illustration starts with adjusting screws closed to their seats. It does not supply a turn count or extend the illustrated H/L arrangement to every carburetor on this sheet.
- The source distinguishes initial engagement at the first detent from final fully-home seating after the series-specific basic setting. Do not treat the first detent as the completed installation.
- Required idle/high-speed settings depend on the exact series; this bulletin supplies no universal screw-turn or RPM setting. Later series-specific service guidance still governs.
- Caps removed to service an adjusting screw or clean the carburetor must not be reused. TI 21/2005 supplies the removal dependency; this is not authorization for permanent limiter removal.
- Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.
Source: TI 50/2006, p. 3 · TI 50/2006, p. 4 · TI 50/2006, p. 5 — Sections 3–3.4 and summary: capped-carburetor service tool and seating stages.
Part numbers (2)
- 5910 890 2304 — Square-bit carburetor screwdriverService tool · Carburetors using 4203 121 2700 fitted caps
- 4203 121 2700 — Limiter capExact tool configuration · New caps; final seating after series-specific basic setting
Service note · FS 550
FS 550 HD22: limiter-cap parts and adjustment stops
Knurled H/L heads retain flush-fitting caps; molded insert stops limit travel.
- Fuel system is HD 22 with limiter caps, described here in connection with EPA regulations. This is not an HD 31 or HD 23 calibration instruction merely because later IPL sheets share models. Delegated TI27/1997 details remain a named bounded source gap.
- Drawing items:1 caps restrict H/L adjustment;2 H screw and 3 L screw have knurled heads retaining caps;4 O-rings seal against the carburetor body;5 inserts have mounting bores with MOLDED STOPS limiting cap travel. Installed caps are FLUSH with the casting. No cap color, numeric travel angle or individual part numbers are printed here.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 3 — Section 2.1.2 and 2.1.2.1; complete 398TI005 KN key 1–5.
No additional parts-table entry added.
Service note · FS 550
FS 550 HD22: capped H and L each 1/4 turn from lean stop
Altitude correction names H only; an excessively lean setting risks lubrication loss and overheating.
- With limiter caps fitted, factory/owner-manual STANDARD setting is H=1/4 turn open and L=1/4 turn open, STARTING FROM THE LEAN STOP in each case. This is not the uncapped seat-referenced basic setting. Corrections remain within integrally molded stops; no numerical adjustment-range angle is specified.
- If running at higher altitude is unsatisfactory, check the standard setting, warm the engine, then turn the HIGH-SPEED screw H CLOCKWISE (leaner). This particular altitude branch names H, not L; do not borrow the two-screw instruction from another carburetor bulletin.
- The warning is that an excessively lean setting can damage the engine through INSUFFICIENT LUBRICATION AND OVERHEATING. The stated purpose of limiting enrichment is historical EPA context, not current compliance certification or permission to remove caps for routine adjustment. Only the reproduced owner-manual standard setting is established, not a complete owner-manual review.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 4 — Section 2.1.2.2 and 398TI006 KN: capped standard setting and altitude branch.
No additional parts-table entry added.
Service note · FS 550
FS 550 HD22 repair: uncapped settings and new limiter caps
H opens 1 1/4 turns and L 1 5/8 turns from seats; removal destroys the old caps.
Later reviewed guidance: BR/SR blowers and FS 550: revised limiter cap keeps the same number · BR/SR blowers and FS 550: square-bit driver for fitted limiter caps
- To replace adjusting screws or clean the carburetor, remove caps using puller 5910 890 4500. First rotate caps/screws COUNTERCLOCKWISE AS FAR AS THE STOP, then screw the puller into the cap COUNTERCLOCKWISE until it comes off. The caps are damaged by disassembly and MUST NOT BE REUSED.
- After fitting adjusting screws, start with screws against their SEATS: open H 1 1/4 turns and L 1 5/8 turns. These are UNCAPPED BASIC settings, distinct from H/L 1/4 turn measured from lean stops with caps installed. No screw seating torque is supplied.
- Fit NEW caps with lugs positioned as shown by the arrows in 398TI008 KN: in the printed face-on view, the left/H cap lug is toward the lower right and the right/L cap lug toward the upper left. Do not substitute another carburetor or later cap geometry. Push the caps until FLUSH WITH THE CASTING (1); the source says this corresponds to the standard setting in 2.1.2.2. No H-first/L-first sequence is specified here.
- The original duplicates the section number 2.1.2.4 for basic setting and idle adjustment; use the titles and page locators, not that number alone. Later 2005/2006 limiter guidance is linked separately, not silently substituted for this 1997 illustrated revision.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 4 · TI 44/1997, p. 5 — Sections 2.1.2.3/2.1.2.4 and 398TI007/008 KN: removal, basic setting and cap installation.
Part numbers (1)
- 5910 890 4500 — Limiter-cap pullerCounterclockwise cap removal · FS 550; Sections 2.1.2.3/2.1.2.4 and 398TI007/008 KN: removal, basic setting and cap installation
Service note · FS 550
FS 550 HD22: 2,500 rpm idle and 50:1 emission evidence
Use LA with a tachometer; other fuel ratios have no emission measurements in this TI.
- Set engine idle to 2,500 rpm using the idle-speed screw LA. USE A TACHOMETER. LA is separate from H/L mixture screws; the adjacent figure labels it separately.
- EPA approval was obtained with a fuel/oil mix ratio of 50:1. NO EMISSION MEASUREMENTS are available for other ratios. This does not establish equivalent emissions at other mixes or current regulatory approval.
- TI27/1997 is referenced for fuel/emission context and Federal Emission Control Systems Utility Engines. It is absent from the retained 690 TIs and verified 766-resource filename inventory; retain that bounded dependency gap, not global absence or fabricated emissions-system instructions.
- Historical TI44/1997 guidance for the named FS 550 configuration only. Shared IPL sheets do not extend these claims to FS 500, FS 550 L, FS 360 or FS 420. Not current stock, verified physical interchange or a complete operating procedure. No hardware operation was performed.
Source: TI 44/1997, p. 5 — Second section 2.1.2.4 idle; sections 2.1.2.5/6 fuel and Federal Emission Control Systems.
No additional parts-table entry added.
Service note · FS 550
FS 550: separate shaft, gearhead and seal lubricants
Keep three lubricant applications distinct; the carburetor kit names HD 22 and HD 23.
- STIHL gear lubricant 0781 120 1109, 3 oz/80 g tube, is for the DRIVE SHAFT IN THE DRIVE TUBE. Gear lubricant 0781 120 1117, 3 oz/80 g tube, is for the GEARHEAD. Lubricating grease 0781 120 1111, 13 oz/370 g tube, is for OIL SEALS. The TI does not state these products are interchangeable.
- Carburetor parts kit 4116 007 1061 explicitly lists Walbro HD 22 and HD 23. Gasket set 4116 007 1051 has no separate application text in its row; do not silently copy the carburetor-kit restriction or infer its component contents. Common service-kit availability does not establish identical HD 22/HD 23 adjustment settings.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 7 · TI 44/1997, p. 8 — Section4 lubricant rows and complete section5.2 servicing-aids table.
Part numbers (5)
- 0781 120 1109 — Drive-shaft gear lubricant;80 gPrinted application only · Only named models/configurations and restrictions in this note
- 0781 120 1117 — Gearhead lubricant;80 gPrinted application only · Only named models/configurations and restrictions in this note
- 0781 120 1111 — Oil-seal lubricating grease;370 gPrinted application only · Only named models/configurations and restrictions in this note
- 4116 007 1061 — Walbro HD22/HD23 carburetor parts kitPrinted application only · Only named models/configurations and restrictions in this note
- 4116 007 1051 — Set of gaskets; contents not specifiedPrinted application only · Only named models/configurations and restrictions in this note
Service note · FS 550
FS 550: clamp-style throttle adjustment and leak-test pressures
Engine pressure/vacuum is±0.5 bar; carburetor inlet needle is tested at 0.8 bar.
- In 398TI 004 KN, screw(1) secures cover(2) and its cable clamp. Slacken screw about TWO OR THREE TURNS until the cover releases the clamp. Hold the throttle trigger fully squeezed, retighten the screw to secure the clamp, THEN release the trigger. This is the printed full-throttle adjustment, not a later throttle-cable design or an engine-running instruction.
- Engine leak test: PRESSURE +7.25 psi(+0.5 bar); VACUUM -7.25 psi(-0.5 bar). Carburetor INLET NEEDLE testing pressure: 11.6 psi(0.8 bar). No dwell time, allowed pressure drop, isolation setup or needle leakage threshold is supplied here. Do not turn these three values into a complete test or use the carburetor pressure for the crankcase.
- If started during repairs/maintenance, the source requires observing local/national safety regulations and owner-manual precautions. It delegates repairs to a service manual; servicing the carburetor, troubleshooting and standard procedures are described in SEPARATE HANDBOOKS, not that manual. The owner manual and these separate handbooks have not been reviewed as complete procedures in this note.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 8 — Section6 repairs context, complete6.1.1 adjustment/398TI004 KN and6.2 leakage-test data.
No additional parts-table entry added.
Service note · FS 550 / FS 360 / FS 420
FS 550: guide assembly, clutch and fuel-system spares
Guide includes its cover and screw; the two hoses retain different numbers.
- Guide item 7 INCLUDES cover 8 and self-tapping screw 9, IS P4x16. Do not confuse this fuel-system grommet 15 with ignition grommet 6. Hoses 14 and 16 have different part numbers; no hose dimensions or routing are supplied by the summary.
- Remark 1 extends ONLY clutch drum 10, segment 11 and tank housing 12 in this group to predecessor FS 360/FS 420. No predecessor-fitment remark is printed for guide 7, cover 8, screw 9, pump 13, hoses 14/16, grommet 15 or HD 22 carburetor 17. The carburetor row is not an HD 23 equivalence statement.
- Historical TI 44/1997 source guidance, not current availability, verified physical interchange or a complete repair procedure. Shared IPL sheets do not extend claims to unnamed variants. No hardware operation was performed.
Source: TI 44/1997, p. 10 — Section7 rows7–17 and remark1.
Part numbers (11)
- 4116 180 7200 — Item7 guide including8 and9Exact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 4116 182 6801 — Item8 coverExact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 9074 478 3025 — Item9 self-tapping screw IS P4x16Exact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 4116 160 2900 — Item10 clutch drum; remark1Exact section7 row; inclusions and remarks retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 084 7801 — Item11 segment; remark1Exact section7 row; inclusions and remarks retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4116 350 0806 — Item12 tank housing; remark1Exact section7 row; inclusions and remarks retained · FS 550 table context; remark1 also names FS 360 and FS 420; preserve assembly/bore restrictions
- 4130 350 6200 — Item13 fuel pumpExact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 4116 358 7602 — Item14 hoseExact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 4133 353 9201 — Item15 grommetExact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 4116 358 7601 — Item16 hoseExact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
- 4116 120 0603 — Item17 carburetor HD22Exact section7 row; inclusions and remarks retained · FS 550 table context; no separate predecessor remark on this row
Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →