Stihl 4116 · Section P · 15 of 16 · 16 parts
Deflector (34.1999), (33.1998)
Fits FS 500, FS 550, FS 550 L.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (16)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 713 4501 | Deflector | 1 |
| 2 | 4110 716 6501 | Clamp | 1 |
| 3 | 4110 716 2900 | Strip | 1 |
| 4 | 9291 021 0140 | Washer 6.4 Fitment / change note → | 2 |
| 5 | 9022 341 1430 | Spline screw IS-M6x50 | 2 |
| 6 | 4119 716 3203 | Skirt | 1 |
| 7 | 4119 710 6000 | Blade | 1 |
| 8 | 4118 713 4105 | Blade | 1 |
| 9 | 9074 478 4125 | Pan head self-tapping screw IS-5x14 | 2 |
| 10 | 4119 711 2100 NLA | Plug option | 1 |
| 11 | 4116 716 6400 | Thrust pad Fitment / change note → option | 1 |
| 12 | 9222 068 0900 | Square nut M6 Fitment / change note → option | 2 |
| 13 | 4116 716 6500 | Clamp Fitment / change note → no longer available from factoryoption | 1 |
| 14 | 9022 341 1420 | Spline screw IS-M6x45 Fitment / change note → option | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4116 007 1016 | Deflector kit | 1 |
| — | 4116 710 8101 | Deflector | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FS 500 / FS 550
FS 500 / FS 550: shredder blade and complete deflector mounting
Initial installation requires blade 4000 713 3902 and complete deflector 4116 710 8103; the deflector shell alone is not the full kit.
- Section 1.1 introduces shredder blade 320-2 with optimized geometry/material and a specially developed robust deflector with riveted aluminium skirt. Drawing 398TI015 KN depicts the blade and deflector. The new deflector replaces 4116 710 8105 and is also suitable for the brush knife; this is not approval for every cutting tool.
- For initial installation, order BOTH shredder blade 4000 713 3902 and deflector assembly 4116 710 8103. The assembly comes with all necessary mounting hardware. The summary distinguishes complete assembly (items 5–12), new shell 4116 710 8104 (items 6 and 7) and previous deflector 4116 710 8105 (items 6–10). Do not treat these as identical kits.
- Drawing 398TI017 KN: stepped sleeve (1) fits over the drive tube and must be riveted in position to define the installed deflector position. The recommended thrust plate (2) is 65 mm diameter; thrust washer (3) is 70 mm diameter. Center the blade exactly on the thrust-plate shoulder and fit hardened guard ring (4) to protect the mounting nut. The diagram places plate below the blade and washer/guard ring above it. No rivet-hole coordinates, torque or unprinted guard-ring order number is inferred.
- The drawing callouts 1–4 on page 1 are NOT the summary item numbers on pages 2–3. Drawing 398TI019 SC shows blade 1, brush knife 2, circular blade 3, shell 5, clamp/nut 6/7, clamp/washer/screw 8/9/10, sleeve/rivet 11/12 and transport guard 13. The previous item 4 and unnumbered complete assembly are not invented as extra visible callouts.
- The table explicitly gives two square nuts, two washers and two M6x45 screws. Rivet A 4x8 has no printed quantity in this TI; the later IPL quantity is not silently substituted. New clamps replace 4116 716 6400 and 4116 716 6500 with 6402 and 6502 endings respectively; the unchanged fasteners retain their numbers.
- Transport guard 4116 790 3901 replaces 4116 790 3900 and now also fits the shredder blade. Remark 1 applies only to previous deflector 4116 710 8105 and previous transport guard: no longer available from factory. Remark 2 applies to both previous clamps: remain available. Introduction is in progress, not the clutch serial threshold in section 2.
- Historical TI34/1999 evidence only; availability and performance claims are dated source statements, not current stock or measured performance. Grouped IPL navigation does not add FS 550 L or other unlisted variants. No hardware operation or physical interchange verification.
Source: TI 34/1999, p. 1 · TI 34/1999, p. 2 · TI 34/1999, p. 3 — FS 500 / FS 550: shredder blade and complete deflector mounting; complete relevant text, drawings and table rows.
Part numbers (15)
- 4000 713 3902 — Shredder blade 320-2New; summary item 1 · FS 500 / FS 550
- 4116 710 8103 — Shredder deflector assembly, including items 5–12Complete initial-installation deflector · FS 500 / FS 550
- 4116 710 8105 — Previous deflector, including items 6–10Previous; remark 1 · FS 500 / FS 550
- 4116 710 8104 — Deflector, including items 6 and 7New shell subassembly; item 5 · FS 500 / FS 550
- 4116 716 6400 — ClampPrevious item 6; remark 2 · FS 500 / FS 550
- 4116 716 6402 — ClampNew item 6 · FS 500 / FS 550
- 9222 068 0900 — Square nut M6, twoUnchanged; item 7 · FS 500 / FS 550
- 4116 716 6500 — ClampPrevious item 8; remark 2 · FS 500 / FS 550
- 4116 716 6502 — ClampNew item 8 · FS 500 / FS 550
- 9291 021 0140 — Washer A 6.4, twoUnchanged; item 9 · FS 500 / FS 550
- 9022 341 1420 — Spline screw IS M6x45, twoUnchanged; item 10 · FS 500 / FS 550
- 4116 711 2501 — Stepped sleeveNew; item 11 · FS 500 / FS 550
- 9438 782 3170 — Rivet A 4x8New; item 12; no quantity printed in TI table · FS 500 / FS 550
- 4116 790 3900 — Transport guardPrevious item 13; remark 1 · FS 500 / FS 550
- 4116 790 3901 — Transport guardNew item 13; modified for shredder blade · FS 500 / FS 550
Wrong number or missing part for the FS 500, FS 550, FS 550 L? Report a correction →