Stihl 4119 · Section G · 6 of 18 · 33 parts
Carburetor C1S-S3E
Fits FS 160, FS 180.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (33)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4116 121 5100 | Inlet needle | 1 |
| 2 | 1120 122 3004 | Spring | 1 |
| 3 | 1120 121 9200 | Spindle | 1 |
| 4 | 1120 121 5000 | Inlet control lever | 1 |
| 5 | 1120 122 6600 | Collar screw | 1 |
| 6 | 4119 121 5400 | Valve jet | 1 |
| 7 | 4119 121 0700 | Cup plug | 1 |
| 8 | 1120 129 0902 | Gasket | 1 |
| 9 | 1120 121 4700 | Metering diaphragm | 1 |
| 10 | 1123 121 0801 | End cover Fitment / change note → | 1 |
| 11 | 4132 122 6600 | Collar screw Fitment / change note → | 2 |
| 12 | 1120 122 3005 | Spring | 2 |
| 13 | 4119 122 6700 | High speed adjustment screw | 1 |
| 14 | 4119 122 6802 | Low speed adjustment screw | 1 |
| 15 | 4119 120 7101 | Throttle shaft with lever | 1 |
| 16 | 4119 122 3000 | Torsion spring | 1 |
| 17 | 1120 122 9000 | E-clip | 2 |
| 18 | 1120 121 3301 | Throttle shutter | 1 |
| 19 | 1120 122 7400 | Round head screw | 1 |
| 20 | 1120 121 7800 | Strainer | 1 |
| 21 | 4119 121 4800 | Pump diaphragm | 1 |
| 22 | 1120 129 0901 | Gasket | 1 |
| 23 | 4119 121 0800 | End cover | 1 |
| 24 | 1120 122 7800 | Oval head screw | 1 |
| 25 | 1120 122 3003 | Spring | 1 |
| 26 | 1120 122 6200 | Idle speed adjustment screw | 1 |
| 27 | 4119 122 3002 | Spring | 1 |
| 28 | 4119 122 4200 | Ball | 1 |
| 29 | 4119 121 2901 | Choke shutter | 1 |
| 30 | 4119 121 3000 | Choke shaft | 1 |
| 32 | 4119 121 8900 | Pin | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4119 120 0602 | Carburetor C1S-S3E Fitment / change note → | 1 |
| — | 4119 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FS 160 / FS 180 / FS 220
FS160/180/220 carburetor: cover-specific screw pairing
C1S-S3 C becomes D without changing the complete carburetor number; cast and steel end covers require different screws.
X 29 643 202 — Model-conditioned introduction of this specific change only; not a model-identification or production-year range.
- From X 29 643 202, carburetor 4119 120 0602 retains the SAME complete number but changes from C1S-S3 C to C1S-S3 D. These suffixes are legible in the original scan; the extracted body corrupts C and D into & and an apostrophe. The original heading reads series 4119, not truncated 411. Figure 323TI001 shows the original cast cover on the LEFT and new steel cover on the RIGHT.
- Light-alloy cast cover 1120 121 0802 is replaced by steel cover 1123 121 0801. Because thickness differs, the CAST cover MUST ALWAYS use screws 1120 122 6601; the STEEL cover ONLY uses the slightly shorter 4132 122 6600. Two flange-head screws are fitted; MOQ 1 is an order minimum, not a change in installed quantity. No screw length, torque or unrestricted mixed pairing is specified.
- Only the modified complete carburetor is supplied by the factory. Original end covers are supplied only while stocks last. Original screws remain available for cast covers and other models; this does not identify those other models or extend this changeover. All other parts as before.
- Later exact-model C1S-S3E sheets show new cover/screws at keys 10/11. Their E designation is later catalog evidence, NOT proof that the TI C-to-D change was really C-to-E. The FS160/180 C1S-S2 sheet independently retains the cast cover/screw pair; it does not make the complete S2 and S3 carburetors interchangeable. Shared FS220 sheet also names K/280/290 variants, which are not added to this section scope.
- Historical TI guidance for the explicitly named models and stated versions only. Shared IPL sheets are navigation, not an extension to every listed variant or proof of unrestricted interchange. Supply statements are historical, not current stock guarantees. No hardware operation was performed.
Source: TI 16/1995, p. 1 · TI 16/1995, p. 2 — Section 1: carburetor end cover, figure 323TI001, complete summary and supply remarks.
Part numbers (5)
- 4119 120 0602 — Complete carburetor C1S-S3 C / Dsame number; modified version only · FS 160; FS 180; FS 220
- 1120 121 0802 — Cast end coverold stock only; original screws required · FS 160; FS 180; FS 220
- 1123 121 0801 — Steel end covernew; MOQ 1; shorter screws only · FS 160; FS 180; FS 220
- 1120 122 6601 — Original flange-head screwtwo fitted; retained for cast cover · FS 160; FS 180; FS 220
- 4132 122 6600 — Shorter flange-head screwtwo fitted; MOQ 1; steel cover only · FS 160; FS 180; FS 220
Wrong number or missing part for the FS 160, FS 180? Report a correction →