← Brushcutters & other equipment · series 4119

Stihl 4119 · Section B · 2 of 17 · 40 parts

Rewind starter, Muffler

Fits FS 220, FS 220 K, FS 280, FS 280 K, FS 290.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425262728293303132334404142434456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (40)

PosPart numberDescriptionQty
1 4223 195 0600 Starter cup Fitment / change note → 1
2 9210 261 1140 Hexagon nut M8x1 1
3 4119 190 0401 Starter cover Fitment / change note → 1
4 0000 967 2035 Nameplate STIHL 1
5 1110 084 9102 Bushing 1
6 9443 825 7130 Hollow rivet 7.5x1x6.8 4
7 9416 868 6630 Hollow rivet 6.5x0.5x6.8 4
8 4116 190 0600 Rewind spring 1
9 1118 195 0300 Spring housing 1
10 1128 190 3400 Starter grip ElastoStart Ø 3,5 mm Fitment / change note → 1
11 1128 190 2900 Starter rope Ø 3.5 mm Fitment / change note → 1
12 0000 190 3401 Starter grip ElastoStart Ø 3.5 mm 1
13 0000 195 7001 Cap 1
14 1113 195 8200 Starter rope Ø 3.5x960 mm Fitment / change note → 1
15 4119 195 0400 Rope rotor 1
16 4116 195 7200 Pawl 1
17 0000 958 0923 Washer 1
18 1118 195 3500 Spring 1
19 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 6
20 4119 149 0600 Muffler gasket 1
21 4119 140 0605 Muffler 1
22 4119 140 0606 Muffler 1
23 4119 140 0600 NLA Muffler 1
24 4119 141 9000 NLA Screen 1
25 4119 145 3000 NLA Screen frame 1
26 9099 021 0810 Self-tapping screw 4.2x9.5 2
27 9307 021 0120 Washer 5.3 2
28 9022 341 1150 Spline screw IS-M5x65 2
29 1110 400 7005 Spark plug Bosch WSR 6 F 1
30 4119 007 1022 NLA Cover plate kit option 1
31 4119 195 6200 NLA Hose option 1
32 9022 341 1090 Spline screw IS-M5x40 option 2
33 9022 341 1220 Spline screw IS-M5x48 option 2
40 1121 195 3400 Starter grip Fitment / change note → 1
41 1113 195 8200 Starter rope Ø 3.5x960 mm Fitment / change note → 1
42 0000 958 0806 Washer 1
43 0000 974 1000 Round head rivet 3x6 Fitment / change note → 2
44 9099 021 2330 NLA Self-tapping screw 3.5x6.5 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2267 Starter rope Ø 3.5 mm / 28 pieces Fitment / change note → not illustratedoption 1
— 0000 930 2203 Starter rope Ø 3.5 mm x 30.5 m Fitment / change note → not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 160 / FS 180 / FS 220 / FS 280

FS 160 / 180 / 220 / 280: clip-in nameplate fits deburred original covers

Polymer plate replaces aluminium; original plate and rivet remain for older machines.

  • Aluminium nameplate 0000 967 2020 changes to polymer clip-in plate 0000 967 2032. The new plate can also fit starter covers with the original plate, but check mounting holes for BURRS and deburr if necessary BEFORE fitting. No drilling or hole enlargement is prescribed.
  • Starter cover 4119 190 0401 keeps its number; unmodified cover remains supplied until factory stocks are exhausted. Original plate and 3x6 round-head rivet 0000 974 1000 remain available for older machines and other models. No unlisted other model is established; rivet is not a required new-plate fastener.
  • Prose says the change occurred some time ago while table marks introduction in progress. Retain those historical statements without inventing a serial; all other parts remain as before.
  • Historical TI 15/1994 guidance for the explicitly named models only; no successor or unlisted variant applicability inferred. Factory supply statements are historical, not current stock claims. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 15/1994, p. 3 — FS 160 / 180 / 220 / 280: clip-in nameplate fits deburred original covers.

Part numbers (4)
  • 4119 190 0401 — Starter cover including nameplateunchanged number; old version while stocks last · FS 160 / 180 / 220 / 280: clip-in nameplate fits deburred original covers
  • 0000 967 2020 — Aluminium nameplateretained for older/other models · FS 160 / 180 / 220 / 280: clip-in nameplate fits deburred original covers
  • 0000 967 2032 — Clip-in polymer nameplatenew; holes must be burr-free · FS 160 / 180 / 220 / 280: clip-in nameplate fits deburred original covers
  • 0000 974 1000 — 3x6 round-head rivetretained for original plate · FS 160 / 180 / 220 / 280: clip-in nameplate fits deburred original covers

Service note · FS 160 / FS 180 / FS 220 / FS 280

FS 160 through FS 280: original and modified starter cups

TI48 explicitly extends replacement suitability to this legacy FS range, not FS 290 on a shared IPL sheet.

  • Starter cup 4116 195 0500 was modified during development of new models and renumbered 4223 195 0600. Introduction is IN PROGRESS; no numeric cutoff is given. New MOQ 10 is an order quantity, not ten installed cups. The old cup is no longer factory available, but the text explicitly retains its replacement suitability.
  • Both modified AND original cups should also be used as replacements for the printed scope “FS 160 through FS 280” and BR 320/400, SR 320/400. This is not every numeric FS model, every model sharing a part number, or proof of suitability for FS 290, FS 500/550, FR 220 or later successors. No dimensional change or installation torque is provided.
  • Exact catalog links represent FS 160, FS 180, FS 220 and FS 280 within the printed range. K variants and FS 290 on the shared drawing are not separately admitted by this note.
  • Historical TI 48/1994 guidance, not current stock or verified physical interchange. Shared IPL sheets do not extend the named source models or variants. No hardware operation was performed.

Source: TI 48/1994, p. 4 — original and modified starter cups.

Part numbers (2)
  • 4116 195 0500 — Original starter cupalso suitable as described; no longer factory available · FS 160 / FS 180 / FS 220 / FS 280 only in the configuration described here
  • 4223 195 0600 — Modified starter cupMOQ 10; introduction in progress · FS 160 / FS 180 / FS 220 / FS 280 only in the configuration described here

Conditional replacement · FS 160 / FS 180 / FS 220 / FS 280 / FS 360 / FS 420 / BR 320 / BR 400 / SR 320 / SR 400

FS / BR / SR starter cup: old and new replacement scope

Modified cup 4223 195 0600 replaces 4116 195 0500; both versions are stated replacements for the additional named models.

  • In the cover scope FS160/180/220/280, starter cup 4116 195 0500 is modified during development of unspecified new models and renumbered 4223 195 0600. The TI explicitly says the modified cup AND THE ORIGINAL VERSION can ALSO be used as replacements for FS360, FS420, BR320/400 and SR320/400. It does not identify the new development models or authorize arbitrary starter-assembly interchange.
  • Introduction is IN PROGRESS; no serial marker is supplied for this change. The nameplate serial on the same page belongs to section 3, not this cup. New cup MOQ 10 is an order minimum. The ORIGINAL cup is NO LONGER AVAILABLE FROM THE FACTORY; historical replacement suitability does not promise continued supply.
  • Later exact-model rewind-starter sheets show 4223 195 0600 at key 1 for the 4119 and 4203 model groups and key 14 for FS360/420. Shared-sheet FS220 K, FS280 K, FS290, FS420 L and BR320 L are not silently added to this TI note. No cup dimensions or mounting torque are provided.
  • Historical TI guidance for the explicitly named models and stated versions only. Shared IPL sheets are navigation, not an extension to every listed variant or proof of unrestricted interchange. Supply statements are historical, not current stock guarantees. No hardware operation was performed.

Source: TI 16/1995, p. 3 · TI 16/1995, p. 4 — Section 4: starter-cup replacement scope, table and supply remark.

Part numbers (2)
  • 4116 195 0500 — Original starter cupreplacement suitability retained; no longer supplied · FS 160; FS 180; FS 220; FS 280; FS 360; FS 420; BR 320; BR 400; SR 320; SR 400
  • 4223 195 0600 — Modified starter cupnew; MOQ 10; explicitly stated replacement scope · FS 160; FS 180; FS 220; FS 280; FS 360; FS 420; BR 320; BR 400; SR 320; SR 400

Historical fitment · FS 160 / FS 180 / FS 220 / FS 280

FS 160 / 180 / 220 / 280: standard ElastoStart from X 32 735 494

Rubber-element grip 1128 190 3400 replaces standard grip 1121 195 3400.

X 32 735 494 — Standard ElastoStart starter grip introduced from this machine number on the named series 4119 models; not the other section changeover.

  • From machine number X 32 735 494 the named series 4119 clearing saws come STANDARD with ElastoStart. The scan header reads 4119; the retained extraction drops its final digit. This is not the optional spring-type 0000 190 3400 of TI07/1996.
  • The three named components are starter grip, RUBBER ELEMENT and starter rope. New ElastoStart grip 1128 190 3400 replaces original 1121 195 3400 for this change. Remark 1 retains the original grip for older machines and other models; it is not a universal-deletion statement.
  • The bulletin expressly delegates construction, function and benefits to TI29/1992. That source is absent from the retained 690 entries and mounted tipages inventory (1992-29-*); the dependency remains a documented source gap, not a complete account of rubber-element construction. No spring-type instructions from TI07/1996 are substituted.
  • Historical TI 08/1996 evidence for the named FS 160, FS 180, FS 220 and FS 280, series 4119. Shared sheets do not add FS 220 K, FS 280 K, FS 290 or FR 220. No hardware operation was performed; factory supply statements are historical, not current stock. Starter and fuel-cap serial changes are independent.

Source: TI 8/1996, p. 1 — FS 160 / 180 / 220 / 280: standard ElastoStart from X 32 735 494.

Part numbers (2)
  • 1121 195 3400 — Original starter gripretained for older machines and other models · FS160/180/220/280; TI08/1996 stated configuration
  • 1128 190 3400 — ElastoStart starter gripnew standard rubber-element version · FS160/180/220/280; TI08/1996 stated configuration

Historical fitment · FS 160 / FS 180 / FS 220 / FS 280

FS 160 / 180 / 220 / 280: ElastoStart rope and accessory supply

New 1128 190 2900 rope is Ø3.5 mm; do not transfer old 960 mm length.

X 32 735 494 — Standard ElastoStart starter grip introduced from this machine number on the named series 4119 models; not the other section changeover.

  • Original rope 1113 195 8200 is explicitly Ø3.5 x 960 mm. New rope 1128 190 2900 is printed ONLY Ø3.5 mm. No new length is specified, so the old 960 mm value is not copied to it. Original rope remains available for older machines and other models (remark 1).
  • Special-accessory original rope 0000 930 2203 is listed as 30.5 m and retains availability for older machines/other models (remarks 1/2). New special-accessory rope 0000 930 2267 is Ø3.5 mm (28x), remark 2. The printed 28x qualifier is preserved; no per-piece length,30.5 m total or cutting scheme is invented.
  • Table dashes mark original/new columns; they do not cancel the explicit original-parts availability remarks. The source does not say the new grip package includes these separately listed ropes.
  • Historical TI 08/1996 evidence for the named FS 160, FS 180, FS 220 and FS 280, series 4119. Shared sheets do not add FS 220 K, FS 280 K, FS 290 or FR 220. No hardware operation was performed; factory supply statements are historical, not current stock. Starter and fuel-cap serial changes are independent.

Source: TI 8/1996, p. 1 — FS 160 / 180 / 220 / 280: ElastoStart rope and accessory supply.

Part numbers (4)
  • 1113 195 8200 — Original rope Ø3.5 x 960 mmretained older-machine/other-model supply · FS160/180/220/280; TI08/1996 stated configuration
  • 1128 190 2900 — New rope Ø3.5 mmnew length unspecified · FS160/180/220/280; TI08/1996 stated configuration
  • 0000 930 2203 — Original 30.5 m ropespecial accessory; retained original supply · FS160/180/220/280; TI08/1996 stated configuration
  • 0000 930 2267 — New rope Ø3.5 mm (28x)special accessory;28x as printed · FS160/180/220/280; TI08/1996 stated configuration

Wrong number or missing part for the FS 220, FS 220 K, FS 280, FS 280 K, FS 290? Report a correction →