Stihl 4126 · Section K · 10 of 14 · 38 parts
Loop handle
Fits FS 88.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (38)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4123 791 0801 | Handle molding, outer | 1 |
| 2 | 4126 182 4506 | Torsion spring | 1 |
| 3 | 4126 182 0806 | Lockout lever | 1 |
| 4 | 4126 182 6210 | Collar screw | 1 |
| 5 | 4123 790 1102 | Handle molding, inner | 1 |
| 6 | 4126 791 5300 | Connector tag | 2 |
| 7 | 4126 182 1705 | Slide control | 1 |
| 8 | 4126 182 4705 | Detent spring | 1 |
| 9 | 4126 182 6205 | Collar screw | 1 |
| 10 | 4126 182 4505 | Torsion spring | 1 |
| 11 | 9417 003 7510 | Push nut | 1 |
| 12 | 4126 182 1007 | Throttle trigger | 1 |
| 13 | 4123 791 9400 | Hose clamp | 2 |
| 14 | 4126 792 6100 | Square washer | 4 |
| 15 | 9022 341 0980 | Spline screw IS-M5x16 | 2 |
| 16 | 9074 478 3065 | Pan head self-tapping screw IS-P4x19 | 4 |
| 17 | 4126 182 4507 | Torsion spring | 1 |
| 18 | 4135 180 1110 | Throttle cable | 1 |
| 19 | not sold separately | Lead 480 mm / 18.9'' not available as a separate item | 1 |
| 20 | not sold separately | Lead 570 mm / 22.4'' not available as a separate item | 1 |
| 21 | 0751 030 8953 NLA | Terminal socket 4.8-1 no longer available from factory | 2 |
| 22 | 0751 030 8470 | Grommet no longer available from factory | 2 |
| 23 | 0751 030 8474 | Terminal socket 4.8-1 no longer available from factory | 2 |
| 24 | 0751 030 8460 | Grommet no longer available from factory | 2 |
| 25 | not sold separately | Hose 170 mm / 6 3/4'' not available as a separate item | 1 |
| 26 | 4130 790 1315 | Loop handle | 1 |
| 27 | 4130 790 8450 | Barrier bar | 1 |
| 28 | 9222 068 0900 | Square nut M6 | 2 |
| 29 | 9022 341 1370 | Spline screw IS-M6x30 | 2 |
| 30 | 4123 791 7400 | Clamp | 2 |
| 31 | 9291 021 0140 | Washer 6.4 | 2 |
| 32 | 9022 341 1350 | Spline screw IS-M6x25 | 2 |
| 33 | 4121 791 7200 | Sleeve Fitment / change note → | 1 |
| 40 | 4123 790 1300 | Loop handle Fitment / change note → | 1 |
| 41 | 4123 791 7400 | Clamp | 2 |
| 42 | 9022 341 1260 | Spline screw IS-M6x12 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0751 010 1110 | Lead 10 m / 33' not illustratedoption | 1 |
| — | 4203 711 7201 | Hose 960 mm / 37 13/16'' not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 88 / FS 108
FS 88 / 108: filter stack, controls and isolation
Foam sits between the cover and felt; no tool is needed for the filter cover.
- Diaphragm carburetor has a thermally insulated cylinder mounting. Air filter diagram: cover 3, foam element 1, felt element 2 toward the engine. Cover removal/refitting needs no tools. Fuel capacity 0.69 l (1.45 US pt); no mixture ratio or filter-part number printed here.
- Control layout is described as FS 72, 74, 76, 86 and 106: throttle trigger lock 4, trigger 5, slide control 6. Starting-throttle, run and stop positions are selected with one hand. Illustration labels STOP, I and START; no bypass of the trigger lock is authorized.
- Clutch shoes have linings and pivot on the flywheel. AV layout is described as FS 74/76, isolating vibration mainly to the engine. These comparisons do not establish universal control, clutch or AV-rubber interchange.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 1 · TI 37/1994, p. 3 · TI 37/1994, p. 5 — FS 88 / 108: filter stack, controls and isolation.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: handle, drive and generic tightening torques
Specific rows override generic all-other M4/M5 entries.
- Pairs are Nm / lbf.ft. Self-tapping B2.9x25, two halves of control handle and left handle: 2.0 / 1.5. IS-M 5x30 control handle and left handle to bike handle: 3.5 / 2.6. IS-P 4x19 two halves of loop handle: 2.0 / 1.5. IS-M 5x16 clamp on control handle (loop-handle version): 3.5 / 2.6.
- IS-M 6x20 clamp screw in AV sleeve: 7.0 / 5.2. IS-M 5x20 gearhead clamp screws: 8.0 / 5.9. IS-M 6x25 lower clamp AND upper clamp to handle support: each 6.0 / 4.4.
- IS-M 11x10 screw plug at gearhead grease filler: 10.0 / 7.4. IS-M 6x14 harness clamp: 4.5 / 3.3. IS-M 6x12 clamp on loop handle: 3.5 / 2.6. IS-M 4x12 setscrew in drive-tube sleeve: 3.0 / 2.2.
- ALL OTHER screws/nuts M4: 2.5 / 1.8; M5: 4.5 / 3.3. These are not substitutes for listed component-specific values or the two explicitly unspecified clamp rows. No tool-mounting nut torque is supplied here.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 8 — handle, drive and generic tightening torques.
No additional parts-table entry added.
Service note · FS 74 / FS 76 / FS 88 / FS 108
FS 74/76/88/108 normal loop handles: barrier conversion kit 1030
Kit includes shoulder strap, deflector, barrier bar and sleeve-use instruction sheet.
- Kit 4130 007 1030 converts FS 74, FS 76, FS 88 and FS 108 NORMAL LOOP HANDLES to loop handles with barrier bar. It is not the discontinued bike-handle-to-loop kits described in section 2.
- Page 2 lists a shoulder strap, deflector, barrier bar and instruction sheet on sleeve 4121 791 7200. After conversion, grass cutting blades and brush knives may be used WITH deflector 4119 713 4500; the deflector condition is not waived by owning the kit.
- Page 8 lists kit 1030 for FS 74 R, 76 R, 88 R and 108 R, consisting of sleeve 9, strap 41, deflector sub-kit 42 and bar 30. See the reviewed complete-accessory-versus-sub-kit note for ordering numbers and limits; the machine-specific sub-kit bill of materials remains a documented source gap.
- Historical TI 39/1995 guidance for its specified configurations, not universal attachment approval, present stock or verified physical interchange. No hardware operation was performed.
- These exact-model IPLs are navigation aids, not evidence of an installed revision. Shared FS 72/74/76 sheet does NOT extend the conversion to FS 72. Only the four named normal-loop-handle configurations are assigned this kit.
Source: TI 39/1995, p. 2 · TI 39/1995, p. 8 — FS 74/76/88/108 normal loop handles: barrier conversion kit 1030.
Part numbers (3)
- 4130 007 1030 — Normal-loop to barrier-bar conversion kitSource-listed component; restrictions in conditions · FS74/76/88/108 normal loop handles: barrier conversion kit1030
- 4121 791 7200 — Sleeve addressed by supplied instruction sheetSource-listed component; restrictions in conditions · FS74/76/88/108 normal loop handles: barrier conversion kit1030
- 4119 713 4500 — Required universal deflectorSource-listed component; restrictions in conditions · FS74/76/88/108 normal loop handles: barrier conversion kit1030
Conditional replacement · FS 74 / FS 76 / FS 88 / FS 108
FS 74/76/88/108 R: older replacement versus production choice
Original and new handle assignments retain production, replacement and variant restrictions.
- Each model has TWO distinct rows: former handle 1 → handle 6, –/X, remark 2 for older-machine replacement; and former handle 1 → handles 6 OR 7, X/X, remark 3. Do not turn the older-machine row into a blanket production/barrier conversion.
- Source series and tube B: FS 74 R = 4133 / item 32 (4133 711 0212 → 4133 711 0213); FS 76 R = 4133 / item 34 (4124 710 7102 → 4124 710 7103); FS 88 R = 4126 / item 34 (same pair); FS 108 R = 4135 / item 36 (4117 710 7101 → 4117 710 7102).
- Page 5 remark 3 says the new tube is used in production AND replacement, also for bike-handle machines. Section 6 remark 14 says the original item 32/34/36 tubes remain available as spares for OLDER LOOP-HANDLE machines. New-tube cross-configuration use does not erase that old-tube restriction.
- Former handle 1 (4123 790 1300) remains available as spare for other models. Kit 4130 007 1030 is the separate four-model normal-loop-to-barrier accessory discussed on pages 2 and 8, not a new bike-to-loop kit.
- Page 5 A refers to the handle figure on page 4 AND the matching item in section 6; B is a drive-tube item number, not a diameter or complete assembly part number. X/X means standard production AND replacement; –/X means replacement only. Blank tube-number cells with remark 1 mean new instruction label with the SAME tube number, not removal of the tube.
- New handle 6 is 4130 790 1316. Handle 7 is NOT available as a separate item: use handle 6 plus barrier bar 30 (4130 791 4400). Neither assembly choice alone authorizes a cutting tool: the page 2 blade/barrier/universal-deflector restrictions still apply.
- The printed source is December 21, 1995; introduction is in progress with mixed inventories, not a serial cutoff or proof of installed revision. Catalog title says New Zealand only while the printed matrix includes Southeast Asia; territory discrepancy retained. Historical TI 39/1995 guidance, not current stock or verified physical interchange. No hardware operation was performed.
- Exact-model IPL navigation only; shared-sheet companion models are NOT added to the source assignment. Printed source series identifiers are retained separately from catalog navigation series.
Source: TI 39/1995, p. 4 · TI 39/1995, p. 5 · TI 39/1995, p. 6 · TI 39/1995, p. 7 · TI 39/1995, p. 8 — Section 5, FS 74/76/88/108 R: older replacement versus production choice; section 6 row/remark joins.
Part numbers (9)
- 4123 790 1300 — Former handle 1Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4130 790 1316 — New loop handle 6Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4130 791 4400 — Barrier bar 30; combine with handle 6 for form 7Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4133 711 0212 — Former tube item 32Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4133 711 0213 — New tube item 32Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4124 710 7102 — Former tube item 34Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4124 710 7103 — New tube item 34Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4117 710 7101 — Former tube item 36Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
- 4117 710 7102 — New tube item 36Source matrix/table component; restrictions in conditions · FS 74/76/88/108 R: older replacement versus production choice
Service note · FS 74 / FS 76 / FS 88 / FS 108
FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
The four listed components do not turn a deflector sub-kit into the complete conversion.
- Item 40 is deflector kit for cutting tools 4130 007 1030, for FS 74 R, FS 76 R, FS 88 R and FS 108 R. It consists of items 9,41,42,30: sleeve 4121 791 7200, shoulder strap 4130 710 9000, deflector KIT 4119 007 1013 and barrier bar 4130 791 4400.
- Item 42 (4119 007 1013) is a sub-kit, NOT the complete item 40 conversion and NOT the same ordering number as universal deflector 4119 713 4500. Page 2 requires the latter WITH the barrier bar for grass cutting blades or brush knives. The source does not list a complete sub-kit bill of materials here; remark 16 refers to the machine parts list.
- The kit includes the sleeve, but remark 9 limits its use to 24 mm (0.945 in) drive tubes. Page 2 also specifies the kit-supplied sleeve instruction sheet; that separate sheet has not been recovered in the bounded source review.
- This is normal-loop-to-barrier conversion, NOT the discontinued bike-to-loop kits 43–48. The item 40 component list does not add handle 6, arbitrary mounting fasteners or a cutting blade to the package.
- Historical TI 39/1995 guidance dated December 21, 1995, not current stock or verified physical interchange. No hardware operation was performed.
- Exact-model IPL links are navigation only, not a verified 1995 kit bill of materials. Shared sheets do NOT add FS 62, FS 72 or FS 180 to these kit assignments. Catalog title New Zealand only conflicts with the printed cover and Southeast Asia matrix entries; territory discrepancy retained.
Source: TI 39/1995, p. 2 · TI 39/1995, p. 7 · TI 39/1995, p. 8 — Section 6, FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit; section 2 stock limits and component-table joins.
Part numbers (6)
- 4130 007 1030 — Complete accessory conversion kit, item 40TI-listed kit or included component; restrictions in conditions · FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
- 4121 791 7200 — Sleeve, item 9; use only on 24 mm tubeTI-listed kit or included component; restrictions in conditions · FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
- 4130 710 9000 — Shoulder strap, item 41TI-listed kit or included component; restrictions in conditions · FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
- 4119 007 1013 — Deflector sub-kit, item 42TI-listed kit or included component; restrictions in conditions · FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
- 4130 791 4400 — Barrier bar, item 30TI-listed kit or included component; restrictions in conditions · FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
- 4119 713 4500 — Required universal deflector; page 2TI-listed kit or included component; restrictions in conditions · FS 74/76/88/108 R: complete accessory kit versus deflector sub-kit
Service note · FS 66 / FS 81 / FS 88
FS 66/81/88: 24 mm bike-to-loop kit 4123 007 1003
Historical model, tube diameter and included-handle distinctions remain explicit.
- Item 45 is for 24 mm (0.945 in) drive tubes on FS 66, FS 81 and FS 88; includes metal loop handle 3 (4126 790 3400). Do not add FS 86 merely because it shares an IPL sheet.
- Original bike-handle-to-loop conversion kit supplied only while factory stocks last (remark 4). Section 2 says NO NEW VERSIONS of these kits will be offered; future conversions use individual handle components. This is not withdrawal of accessory kit 4130 007 1030.
- The printed inclusion is not an exhaustive kit bill of materials: remark 16 refers component parts to the parts list for the machine concerned. Retained 01-2012 IPLs are later references, not established 1995 kit-content evidence. Do not fill the historical kit from neighboring drawing rows.
- Historical TI 39/1995 guidance dated December 21, 1995, not current stock or verified physical interchange. No hardware operation was performed.
- Exact-model IPL links are navigation only, not a verified 1995 kit bill of materials. Shared sheets do NOT add FS 62, FS 72 or FS 180 to these kit assignments. Catalog title New Zealand only conflicts with the printed cover and Southeast Asia matrix entries; territory discrepancy retained.
Source: TI 39/1995, p. 3 · TI 39/1995, p. 7 · TI 39/1995, p. 8 — Section 6, FS 66/81/88: 24 mm bike-to-loop kit 4123 007 1003; section 2 stock limits and component-table joins.
Part numbers (2)
- 4123 007 1003 — Original bike-to-loop conversion kitTI-listed kit or included component; restrictions in conditions · FS 66/81/88: 24 mm bike-to-loop kit 4123 007 1003
- 4126 790 3400 — Included metal loop handle, item 3TI-listed kit or included component; restrictions in conditions · FS 66/81/88: 24 mm bike-to-loop kit 4123 007 1003
Wrong number or missing part for the FS 88? Report a correction →