← FS 81, FS 86 · FS 88 · FS 106

Stihl 4126 · Section L · 11 of 14 · 20 parts

Gear head

Fits FS 88.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718234556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (20)

PosPart numberDescriptionQty
1 4133 641 0300 Gear housing 1
2 9503 003 9853 Grooved ball bearing 609-2Z 1
3 not sold separately Drive pinion not available as a separate item 1
4 not sold separately Spur bevel gear not available as a separate item 1
5 9503 003 9850 Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 2
6 9455 621 0750 Circlip 9x1 1
7 9456 621 2660 Circlip 24x1.2 1
8 4124 642 0600 Drive shaft 1
9 9503 003 5190 Grooved ball bearing 6001-2RS 1
10 9456 621 3100 Circlip 28x1.2 1
11 4119 713 6500 Screw plug 1
12 0000 958 0503 Washer 2
13 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
14 4126 710 3800 Thrust plate 1
15 4126 713 1600 Thrust washer 1
16 4126 713 3100 Rider plate 1
17 4126 642 7600 Collar nut M10x1 l/h thread 1
18 0781 120 1117 Gear lubricant 80 g Fitment / change note → option 1
Not numbered on the diagram — assemblies, kits and options
— 4133 640 0100 Gearhead 1
— 4124 640 7300 Set of pinions 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 88 / FS 108

FS 88 / 108: drive shaft and left-hand tool thread

Six shaft bushes and model-specific bevel-gear ratios are stated.

  • Rigid drive shaft is supported in SIX bushes. Gearhead described as same as FS 66 through 106; tool mounting (7) as FS 74, 76, 86 and 106 with M10x1 LEFT-HAND THREAD. No exact gearhead part number is given; the family comparison is not blanket interchange evidence.
  • Helical bevel gear drive: FS 88 ratio 1.36; FS 108 ratio 1.33. Page 5 lubrication names multipurpose grease 0781 120 1109, conflicting with page 7 gearhead-specific lubricant; see the separate lubricant-conflict note, not an inferred equivalence.
  • Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.

Source: TI 37/1994, p. 4 · TI 37/1994, p. 5 — FS 88 / 108: drive shaft and left-hand tool thread.

Part numbers (1)
  • 0781 120 1109 — Multipurpose grease listed for gearhead on page 5; conflicts with page 7historical listed item · FS 88 / 108: drive shaft and left-hand tool thread

Service note · FS 88 / FS 108

FS 88 / 108: gearhead lubricant conflict

Page 5 names multipurpose grease; page 7 lists dedicated gear lubricant.

  • SOURCE CONFLICT: section 4.2 page 5 specifies STIHL multipurpose grease 0781 120 1109 for the gearhead. Page 7 instead lists that multipurpose grease for DRIVE SHAFT and STIHL gear lubricant 0781 120 1117 / 1118 for GEARHEAD. Neither table is silently preferred; this does not establish that the products are interchangeable. Exact applicable service guidance is needed before choosing a lubricant.
  • Page 7 multipurpose grease: 80 g (3 oz) 0781 120 1109; 225 g (8 oz) 0781 120 1110, drive shaft. Gear lubricant: 80 g (3 oz) 0781 120 1117; 225 g (8 oz) 0781 120 1118, gearhead. Package mass is NOT a fill quantity.
  • Low-temperature lubricant 0781 417 1315, 100 ml (0.21 US pt) bottle, is for the starter rewind spring. No gearhead substitution or fill quantity is implied.
  • Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.

Source: TI 37/1994, p. 5 · TI 37/1994, p. 7 — FS 88 / 108: gearhead lubricant conflict.

Part numbers (5)
  • 0781 120 1109 — Multipurpose grease 80 g; conflicting gearhead/drive-shaft allocationhistorical listed item · FS 88 / 108: gearhead lubricant conflict
  • 0781 120 1110 — Multipurpose grease 225 g; drive shaft on page 7historical listed item · FS 88 / 108: gearhead lubricant conflict
  • 0781 120 1117 — Gear lubricant 80 g; gearhead on page 7historical listed item · FS 88 / 108: gearhead lubricant conflict
  • 0781 120 1118 — Gear lubricant 225 g; gearhead on page 7historical listed item · FS 88 / 108: gearhead lubricant conflict
  • 0781 417 1315 — Low-temperature lubricant 100 ml; rewind springhistorical listed item · FS 88 / 108: gearhead lubricant conflict

Service note · FS 88 / FS 108

FS 88 / 108: handle, drive and generic tightening torques

Specific rows override generic all-other M4/M5 entries.

  • Pairs are Nm / lbf.ft. Self-tapping B2.9x25, two halves of control handle and left handle: 2.0 / 1.5. IS-M 5x30 control handle and left handle to bike handle: 3.5 / 2.6. IS-P 4x19 two halves of loop handle: 2.0 / 1.5. IS-M 5x16 clamp on control handle (loop-handle version): 3.5 / 2.6.
  • IS-M 6x20 clamp screw in AV sleeve: 7.0 / 5.2. IS-M 5x20 gearhead clamp screws: 8.0 / 5.9. IS-M 6x25 lower clamp AND upper clamp to handle support: each 6.0 / 4.4.
  • IS-M 11x10 screw plug at gearhead grease filler: 10.0 / 7.4. IS-M 6x14 harness clamp: 4.5 / 3.3. IS-M 6x12 clamp on loop handle: 3.5 / 2.6. IS-M 4x12 setscrew in drive-tube sleeve: 3.0 / 2.2.
  • ALL OTHER screws/nuts M4: 2.5 / 1.8; M5: 4.5 / 3.3. These are not substitutes for listed component-specific values or the two explicitly unspecified clamp rows. No tool-mounting nut torque is supplied here.
  • Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.

Source: TI 37/1994, p. 8 — handle, drive and generic tightening torques.

No additional parts-table entry added.

Service note · FS 88 / FS 108

FS 88 / 108: control, starter and drive repair times

Rows 11–22 retain the common FS 88 / FS 108 minute column.

  • MINUTES, trained personnel and properly equipped workshop: 11 bike handle and throttle control 10; 12 rewind starter, test run 15; 13 clutch, test run 20; 14 muffler 10; 15 air filter 5; 16 stop switch, test run 10.
  • 17 clutch housing 20; 18 drive tube 25; 19 replace COMPLETE gearhead OR bearing housing 5; 20 limit stop OR deflector 10; 21 drive shaft 15; 22 fuel tank 15. Complete-unit replacement time is not a gearhead rebuild allowance. Bike-handle row does not specify a separate loop-handle time.
  • None of rows 11–22 has the asterisk for test run under load; retain any explicit test-run wording without extending the starred-row footnote. These are historical labor-reference values, not permission to run a machine or evidence of a completed repair.
  • Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.

Source: TI 37/1994, p. 12 — control, starter and drive repair times.

No additional parts-table entry added.

Wrong number or missing part for the FS 88? Report a correction →