← FS 400, FS 450, FS 480

Stihl 4128 · Section F · 6 of 21 · 32 parts

Carburetor housing, Air filter

Fits FS 400, FS 450, FS 480.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415171819220212223242534404156789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 4128 120 0103 Carburetor housing 1
2 4128 120 0152 Carburetor housing 1
3 4128 120 0151 Carburetor housing 1
4 0000 963 1403 Bushing 1
5 4134 122 6601 Collar screw 2
6 4128 182 0700 Grommet 1
7 4134 129 3000 Sealing ring 1
8 0000 951 1100 Screw IS-D5x20 4
9 0000 350 6201 Fuel pump 1
10 4130 350 6200 Fuel pump → replaced by 4128 120 0100 TI 6/2009 1
11 not sold separately Hose 2.2x5.4x67 mm, R1 not available as a separate item 1
12 4128 129 0900 Gasket 1
13 4128 120 0607 Carburetor C1Q-S154 1
13 4128 120 0609 Carburetor C1Q-S156 1
14 not sold separately Carburetor C1Q-S113 1
14 4128 120 0651 Carburetor C1Q-S34H Fitment / change note → → replaced by 4128 120 0603 TI 46/2003 1
15 4128 182 9500 Choke knob 1
17 4128 140 2800 Filter housing 1
18 9210 260 0700 Hexagon nut M5 1
19 4134 123 7500 Grommet 1
20 9216 261 0700 Hexagon nut M5 2
21 4134 141 0300 Air filter 1
22 4128 140 1000 Filter cover 1
23 4128 141 8000 Screw plug 1
24 4128 141 2500 Cover option 1
25 4128 141 0310 Air filter option 1
40 4128 123 7501 Grommet 1
41 not sold separately Carburetor C1Q-S33B no longer available from factory 1
Not numbered on the diagram — assemblies, kits and options
— 4128 120 0150 Carburetor housing 1
— 0000 930 2802 Hose 2.2x5.4 mm x 1 m, R1 not illustratedoption 1
— 4128 007 1001 Intake air preheating kit option 1
— 4128 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450

FS120/200/350/400/450: paper filter and compensator system

Larger filter area and carburetor pressure compensation are paired features.

  • New longlife air-filter system uses a PAPER FILTER ELEMENT with larger effective surface area. Carburetor compensator offsets pressure changes as the filter loads with dirt; this is not permission to operate with a missing or damaged filter.
  • Drawing250TI007 KN shows cover, pleated element, filter housing and carburetor with COMPENSATOR STUB. It supplies no part numbers, washing method, replacement interval or universal retrofit dimensions. One adjusting screw is stated; original carburetor-specific details are separate.
  • No filter from predecessor FS88/108/160/180/220/280 is declared interchangeable. Feature evidence does not equate later carburetor revisions with C1Q-S34A/C1Q-S36B.
  • Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.

Source: TI 42/1997, p. 2 — Section1 carburetor/air-filter description and full250TI007 KN illustration.

No additional parts-table entry added.

Service note · FS 120 / FS 200 / FS 350 / FS 450

FS 120 / 200 / 350 / 450: match throttle-cable nipple and carburetor pin

Original replacement cables retain their numbers; fitting one to a new-style machine requires the supplied original pin.

  • The heading explicitly names FS 120, 200, 350 (series 4134) and FS 450 (series 4128). Section 1.1 announces a new cable nipple WITH A COLLAR and a new carburetor pin WITH A THROUGHHOLE in the near future. The table has additional model names, preserved separately in the two carburetor notes rather than silently changing this heading.
  • Figure 250TI018 KN shows the ORIGINAL attachment: nipple (1), pin (2), cable (3), carburetor (4). Figure 250TI019 KN compares original nipple (1) with original pin (2), and new collared nipple (5) with new pin (6). These are figure callouts, not summary-table item numbers: table item 5 is the original pin, not the new nipple.
  • New carburetors are equipped with the new pin (6) and ALSO supplied with original pin (2). The instructions determine which pin to use according to the cable nipple. The original pin is 4128 121 8900; the new pin is 4128 121 8901. Supplying both does not authorize mixing the illustrated nipple/pin pairs.
  • Replacement throttle cables with the ORIGINAL nipple WITHOUT COLLAR remain available and come with original pin (2) and an instruction sheet. Their PART NUMBERS REMAIN UNCHANGED; no actual cable number is printed, so none is inferred from the later catalog. When fitting this original-style replacement cable to a machine supplied with the new nipple, REPLACE new pin (6) on the carburetor with supplied original pin (2). This is not a direction to remove a collar from the cable.
  • Section 1.3 requires the original cable nipple to be properly seated in the carburetor pin. Adjust the cable exactly as described in the SERVICE MANUAL. When correctly adjusted, the nipple must NOT JUMP OUT when the throttle trigger is suddenly released from the fully open position. The manual and instruction-sheet referrals are retained; this bulletin does not supply the full adjustment procedure or authorize a running-engine test.
  • The introduction line says THROTTLE CABLES: IN PROGRESS, with no serial or date boundary. A same-number cable cannot be dated or identified by number alone. All other parts as before. The last-TI references (FS 120/200:42.97; FS 350/450:20.98), copyright 1998 and documentation 6334 are bibliography, not changeover serials.
  • The later catalog housing sheets are model context, not proof that all carburetor revisions use the same attachment. Shared sheets include FS 120R/200R/250 and FS 480; those variants are not added to the bulletin’s named models. Prior conflicts remain unchanged.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 19/1998, p. 1 · TI 19/1998, p. 2 — Page 1 sections 1.1–1.2 and both figures; page 2 complete service note1.3, introduction and footer.

Part numbers (2)
  • 4128 121 8900 — Original carburetor attachment pinMatch original nipple without collar · Original-style replacement throttle cable
  • 4128 121 8901 — New carburetor attachment pinMatch new collared nipple · New-style cable attachment

Historical fitment · FS 400 / FS 450 / FR 450

FS 400 / 450, FR 450: three C1Q-S34 revisions

Original S34A, interim S34B and new S34C have distinct supplied contents; new carburetor includes both attachment pins.

  • The second summary group explicitly names FS 400, 450 and FR 450, although the page 1 series 4128 heading names only FS 450. Retain the broader table scope without extending it to FS 480. No FR 450 IPL sheet was found in the canonical local parts dataset; FR 450 is source-table applicability only, not an invented assembly association.
  • ORIGINAL: C1Q-S34A, 4128 120 0602, includes item 5 (original pin 8900). INTERIM: C1Q-S34B, 4128 120 0650, includes items 5 and 10 (original pin 8900 and grommet 7502). NEW: C1Q-S34C, 4128 120 0651, includes items 5, 6, 10 (BOTH pins 8900/8901 and grommet 7502). Original pin 8900 is still included with the new assembly; new pin 8901 is not a universal replacement for the old nipple.
  • Item10 grommet 4128 123 7502 has a dash in the original column and the SAME number in interim and new columns. It is NOT the first group’s 4134 123 7502 grommet. Pin item 5 is 4128 121 8900; item 6 is 4128 121 8901. The summary shares those numbered pin rows between both model groups.
  • Remark1 applies to original S34A: no longer available from factory. Remark2 applies to interim S34B: only supplied while existing factory stocks last. All other parts as before. The only introduction statement is throttle cables IN PROGRESS; no carburetor serial cutoff or production date is supplied.
  • The retained SCS 01-2012 USA FS 400/450/480 F housing sheet lists 4128 120 0651 as C1Q-S34H, whereas this 1998 table calls it C1Q-S34C. Keep both edition-specific designations; do not infer identical internal parts or claim that the later S34H listing contradicts the original scan. Later S154/S156/S113/S33 alternatives and the shared FS 480 sheet do not expand this TI’s fitment.
  • The original/new nipple pairing, supplied instruction sheet, proper seating and exact service-manual adjustment requirement remain as described in the companion cable note. No full adjustment procedure is claimed from the summary table.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 19/1998, p. 1 · TI 19/1998, p. 2 — Page 2 section 1.4 second group, rows 7–10 with shared pins 5–6 and remarks; page 1 pairing context.

Part numbers (6)
  • 4128 120 0602 — Carburetor C1Q-S34AOriginal; includes item 5 · FS 400 / 450 and FR 450 summary group
  • 4128 120 0650 — Carburetor C1Q-S34BInterim; includes items 5, 10 · FS 400 / 450 and FR 450 summary group
  • 4128 120 0651 — Carburetor C1Q-S34CNew; includes items 5, 6, 10 · FS 400 / 450 and FR 450 summary group
  • 4128 123 7502 — GrommetSame interim/new number · FS 400 / 450 and FR 450 summary group
  • 4128 121 8900 — Original pinIncluded in all three versions · FS 400 / 450 and FR 450 summary group
  • 4128 121 8901 — New pinAdditional pin in new version · FS 400 / 450 and FR 450 summary group

Wrong number or missing part for the FS 400, FS 450, FS 480? Report a correction →