← Edgers & other equipment · series 4130

Stihl 4130 · Section G · 7 of 9 · 23 parts

Clutch, Control handle

Fits FC 44.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 4140 160 2000 Clutch → replaced by 4140 160 2001 TI 27/2001 1
2 4140 162 7901 Tension spring 2
3 4130 162 9100 Spacer sleeve 1
4 4140 162 8900 Washer 1
5 4140 160 2903 Clutch drum 1
6 4130 161 0501 Clutch housing 1
7 4130 967 1510 Model plate FC 44 1
8 9075 478 4155 Pan head self-tapping screw IS-D5x24 4
9 4130 710 6701 Hose clamp 1
10 9022 341 1010 Spline screw IS-M5x18 1
11 9210 260 0700 Hexagon nut M5 1
12 4130 791 7600 Handlebar support 1
13 4130 791 2005 Handle hose 1
14 4130 182 1315 Handle molding, left 1
15 4130 182 1000 Throttle trigger 1
16 4130 182 4500 Torsion spring 1
17 4130 182 0805 Lockout lever 1
18 4130 182 0800 Lockout lever 1
19 0000 997 0715 Compression spring 1
20 4130 430 0200 Stop switch 1
21 4130 432 2010 Slide 1
22 4130 182 1310 Handle molding, right 1
23 9099 021 2810 Self-tapping screw 3.9x19 4

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FC 44

FC 44: fuel mixture, choke and carburetor test conditions

Walbro WT160 basic settings and blade-free cutoff speed retain their exact conditions.

  • Diaphragm-controlled Walbro WT160, flange-mounted to diaphragm carrier, has max-speed control valve and integral fuel pump. Manual pump primes carburetor before start; surplus fuel returns automatically to tank. Tank 0.51 L (1.1 US pt). Historical fuel instruction: brand-name regular gasoline unleaded OR leaded; 50:1 with STIHL1:50 oil, 25:1 with OTHER branded two-stroke oils. Do not collapse to one universal oil ratio.
  • Ring-shaped foam filter 1; cover 2 rotates choke shutter between end-stop-defined RUN/CHOKE. FS44-type controls: stop slide 3, trigger interlock 4, trigger housing 5, trigger/latch 6. Starting-throttle position engages latch in housing notch. These are source controls, not permission to actuate unattended.
  • Basic H and L settings EACH back off ONE FULL TURN; printed parenthesis says screws initially HARD AGAINST THEIR SEATS. Preserve wording as historical reference, not a recommendation to force/torque delicate needles. No seating torque or complete live-tuning procedure is supplied.
  • Max permissible cut-off speed 9300 rpm ±700 WITHOUT CUTTING BLADE, not loaded working speed. Idle 3100 rpm. Carburetor leakage closing pressure 0.8 bar (11.6 psi). Crankcase test 0.5 bar (7.25 psi) GAUGE pressure and 0.4 bar (5.8 psi) UNDER VACUUM; latter is vacuum magnitude, not a second positive pressure. No test duration/leakdown limit given.
  • Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.

Source: TI 24/1994, p. 2 · TI 24/1994, p. 3 · TI 24/1994, p. 4 · TI 24/1994, p. 5 · TI 24/1994, p. 6 — fuel mixture, choke and carburetor test conditions.

No additional parts-table entry added.

Service note · FC 44

FC 44: component-specific tightening torques

Clutch drum 2.5 Nm differs from clutch 17 Nm; depth-wheel 21 Nm is not a blade-nut setting.

  • Source Nm / lbf.ft pairs, with exact thread/joint association: captive spline IS8–32 inch, clutch drum to crankshaft 2.5/1.8; clutch 3/8–24 inch, clutch to crankshaft 17/12.5; B3.5×9.5, backing plate/diaphragm/diaphragm carrier AND frame on muffler 2/1.5; B3.9×19, control handle 2.5/1.8; IS-DG5×16, loop handle 2.5/1.8.
  • IS-TT4.8×19: fan housing to spiral housing 3.0/2.2; diaphragm carrier to crankcase 4.5/3.3. IS-DG5×24: shroud to fan housing 3.5/2.6; clutch/starter housing to fan housing 3.5/2.6. IS-DG5×60: shroud/carburetor/diaphragm carrier 3.5/2.6; muffler to cylinder 6.5/4.8 (printed German “Schalldämpfer am Zylinder”).
  • IS-M4×20, ignition module to cylinder 3.5/2.6; IS-M5×18, clamp on clutch housing 6.5/4.8; IS-M6×18, cylinder to crankcase 14.0/10.3; IS-TT5.2×14, spiral housing to crankcase 14.0/10.3; M6×50 pan-head, clamp screw in loop handle 3.5/2.6; IS-M11×10 screw plug, gearhead 10.0/7.5.
  • M14×1.25 spark plug 19.0/14.0; P5×14 special spline, filter cover to shroud 2.5/1.8; IS-M6×20, gearhead clamp screw 7.5/5.5; IS-M6×25, clamp to deflector 7.5/5.5; M6 clamp screw, clamp on deflector 7.5/5.5; IS-DG5×12, clamp for clamp screw AND flap to deflector 5.5/4.0; M10 collar screw, depth wheel 21/15.5.
  • All 24 numeric torque rows preserved. Inch-thread asterisks apply to IS8–32 and 3/8–24, not adhesive requirements. Table gives NO M8 BLADE-NUT torque. Do not transfer 21 Nm wheel or 17 Nm clutch setting to blade nut. Rounded imperial values retained as printed; no live tightening validation.
  • Historical TI 24/1994 for FC44 only; shared-engine or design-principle comparisons are not universal loose-part interchange. No serial cutoff supplied. Source date November 10, 1994; referenced manuals are not whole-manual acceptance. Owner-manual precautions remain required. No physical interchange test was performed.

Source: TI 24/1994, p. 6 — component-specific tightening torques.

No additional parts-table entry added.

Wrong number or missing part for the FC 44? Report a correction →