← Edgers & other equipment · series 4133

Stihl 4133 · Section A · 1 of 7 · 23 parts

Crankcase, Cylinder

Fits BG 72.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121213141415161718192334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 4133 020 2801 Crankcase, starter side 1
2 9380 620 2570 Roll pin 5x12 2
3 9503 003 0242 Grooved ball bearing 6201 2
4 9640 003 1195 Oil seal 12x22x5 2
5 4133 020 2601 Crankcase, fan side 1
6 4133 030 0400 Crankshaft 1
7 9022 341 1050 Spline screw IS-M5x25 3
8 4133 022 0501 Cylinder Ø 33mm 1
9 4133 034 0500 Piston Ø 33 mm 1
10 4133 034 3000 Piston ring Ø 33x1.5 mm 2
11 4112 034 1500 Piston pin 1
12 9463 650 0805 Snap ring 8x0.7 2
13 9512 004 1820 Needle cage 8x11x10 1
14 4133 036 8901 Thrust washer 2
15 4133 029 2300 Cylinder gasket 1
16 9022 371 1020 Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 2
17 0000 400 7000 Spark plug NGK BPMR7A 1
17 1110 400 7005 Spark plug Bosch WSR 6 F 1
18 0000 998 0606 Torsion spring 1
19 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
Not numbered on the diagram — assemblies, kits and options
— 4133 020 1201 Cylinder with piston Ø 33 mm 1
— 4133 030 2000 Piston Ø 33 mm 1
— 0783 830 2000 Tube of sealant Dirko HT red not illustrated 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BG 72

BG 72: uprated engine needs all new parts

From X 31 409 901; approximately 8% more power to 0.7 kW / 0.95 bhp requires the complete upgrade.

X 31 409 901 — Printed BG 72 uprated-engine introduction; not a series-wide production or successor cutoff.

  • FROM X 31 409 901, engine power increases approximately 8% to 0.7 kW (0.95 bhp). Changes: different port timing, higher compression ratio, enlarged inlet port, modified transfer ports, modified gasket and spacer flange. No numerical port timing or compression ratio is provided.
  • Factory supply describes new cylinder, gasket and spacer flange as universal replacement parts within this BG 72 instruction. ONLY NEW versions may repair NEW machine versions, otherwise loss of power and running problems may occur. Increasing an OLD machine to approximately 0.7 kW is possible ONLY IF ALL NEW PARTS ARE INSTALLED; a cylinder or gasket alone is not the stated upgrade.
  • Mandatory companion hardware remains part of the upgrade: M5 x 20 cylinder screws at 10 Nm (7.5 lbf.ft), M5 x 56 intake screws and plugs, M5 x 25 flange screws and A 5.3 washers. The 10 Nm torque belongs to the cylinder screws, not every intake fastener.
  • The footer is June 19, 1995, with copyright 1995. Last TI28.92 is a prior-bulletin pointer, not a missing prerequisite for this self-contained instruction.
  • TI03/1995 prints BG 72, series 4227; retained exact-model BG 72 sheets are cataloged under 4133. Links are model-label navigation, not proof of series equivalence or applicability to BG 75, HS machines or other models. Verify the actual configuration.
  • Historical TI03/1995 guidance only. Factory supply and power claims are historical, not current stock or measured results. No hardware operation was performed.

Source: TI 3/1995, p. 1 · TI 3/1995, p. 2 · TI 3/1995, p. 3 — BG 72: uprated engine needs all new parts.

No additional parts-table entry added.

Service note · BG 72

BG 72: uprated cylinder requires longer screws

New cylinder 4133 020 1250 uses two M5 x 20 screws; old M5 x 16 screws risk cylinder and crankcase damage.

X 31 409 901 — Printed BG 72 uprated-engine introduction; not a series-wide production or successor cutoff.

  • New cylinder has an approximately 3 mm (0.12 in) higher base flange and larger inlet. Illustration 356TI001 shows original/new base dimensions 7/10, inlet widths 15/19 and inlet heights 9/10.5 (printed 10,5). Cylinder inlet width 15/19 is NOT the gasket window width 16/19 mm.
  • Cylinder 4133 022 0500 becomes printed 4133 020 1250 (table item 1). The original cylinder is no longer factory-available; all other parts are as before except the listed changes. No complete-cylinder-with-piston offering or inclusion of new screws in the cylinder package is stated in this table.
  • TWO new M5 x 20 screws 9022 371 1020 (item 2) MUST secure the new cylinder at 10 Nm (7.5 lbf.ft), including installation on an older machine. DO NOT USE original M5 x 16 screws 9022 341 0980 with the new cylinder: the source warns of cylinder and crankcase damage. Original screws remain available as spare parts, not permission to reuse them here.
  • Retained 2012 BG 72 sheet A lists separate cylinder 4133 022 0501, unlike the TI’s printed 4133 020 1250. Preserve both identifiers; no correction or unprovided supersession inferred. Later catalog screw-change annotations do not silently alter this dated 1995 instruction.
  • TI03/1995 prints BG 72, series 4227; retained exact-model BG 72 sheets are cataloged under 4133. Links are model-label navigation, not proof of series equivalence or applicability to BG 75, HS machines or other models. Verify the actual configuration.
  • Historical TI03/1995 guidance only. Factory supply and power claims are historical, not current stock or measured results. No hardware operation was performed.

Source: TI 3/1995, p. 1 · TI 3/1995, p. 2 · TI 3/1995, p. 3 — BG 72: uprated cylinder requires longer screws.

Part numbers (4)
  • 4133 022 0500 — Cylinderoriginal; unavailable · BG 72; TI03/1995 conditions
  • 4133 020 1250 — Cylinderprinted new number · BG 72; TI03/1995 conditions
  • 9022 341 0980 — Spline screw IS-M5 x16two original; prohibited with new cylinder · BG 72; TI03/1995 conditions
  • 9022 371 1020 — Spline screw IS-M5 x20two required; 10 Nm · BG 72; TI03/1995 conditions

Wrong number or missing part for the BG 72? Report a correction →