← Edgers & other equipment · series 4133

Stihl 4133 · Section B · 2 of 9 · 20 parts

Rewind starter, Muffler

Fits FC 72.

Parts diagrams →

Historical fitment & changes (12) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101112131415161723456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (20)

PosPart numberDescriptionQty
1 4133 190 2002 Carrier 1
2 4133 195 7201 Pawl 1
3 0000 998 0612 Torsion spring Fitment / change note → 1
4 4133 190 0400 Starter cover 1
5 4137 190 1100 Rope rotor with rewind spring Fitment / change note → 1
6 0000 195 8200 Starter rope Ø 3x800 mm Fitment / change note → 1
7 9104 003 0960 Self-tapping screw P5.5x12 1
8 4123 195 3400 Starter grip 1
9 4133 967 1503 Model plate FC 72 1
10 9022 341 0980 Spline screw IS-M5x16 5
11 4133 149 0601 Muffler gasket Fitment / change note → 1
12 4133 140 0606 Muffler Fitment / change note → 1
13 4133 145 1001 Insert Fitment / change note → 1
14 1113 141 9000 NLA Screen 1
15 4133 145 0601 Cover plate Fitment / change note → 1
16 9022 313 0610 Spline screw IS-M4x6 Fitment / change note → 4
17 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 1
Not numbered on the diagram — assemblies, kits and options
— 4133 190 4001 Rewind starter 1
— 0000 930 2208 NLA Starter rope Ø 3 mm x 30.5 m not illustratedoption 1
— 4133 007 1051 Set of gaskets Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76

TI24/2002: three starter-rope stages and model scope

Keep the original, interim and final rope sizes separate; HS72/74/76 do not inherit the grip change.

  • Original starter rope 4123 195 8200 is 0.105 in / 2.7 mm diameter and 31.5 in / 800 mm long. Interim rope 0000 195 8200 is 0.120 in / 3 mm diameter and the same 31.5 in / 800 mm length. Final rope 4137 195 8200 returns to 0.105 in / 2.7 mm diameter but increases length to 35.8 in / 910 mm. Do not confuse unchanged diameter with unchanged length.
  • The interim rope is included in ElastoStart 0000 190 3400; the final rope is used in ElastoStart 0000 190 3403. Those grip associations describe the main starter branch; section 2.7 extends subsections 2.1, 2.3, 2.4 and 2.5 to HS 72, HS 74 and HS 76, but not subsection 2.2. No ElastoStart-grip replacement is authorized for those three models by this TI.
  • Summary remarks distinguish earlier-to-interim from interim-to-new changes. Original rope 4123 195 8200 and interim rope 0000 195 8200 remain available for other models; their removal from this branch does not mean universal discontinuation. Section 2.6 states the new starter parts are fully interchangeable with previous machine versions within the applicable section 2 model scope.
  • These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.

Part numbers (3)
  • 4123 195 8200 — Starter rope 2.7 x 800 mmOriginal; retained for other models · Named section 2 models only; see conditions
  • 0000 195 8200 — Starter rope 3 x 800 mmInterim; retained for other models · Named section 2 models only; see conditions
  • 4137 195 8200 — Starter rope 2.7 x 910 mmFinal version · Named section 2 models only; see conditions

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85

TI24/2002: ElastoStart grip change excludes HS72/74/76

The new grip follows the longer final rope; do not extend subsection2.2 to the restricted hedge-trimmer group.

  • ElastoStart grip 0000 190 3403 replaces 0000 190 3400 together with the introduction of final rope 4137 195 8200 (2.7 x 910 mm). The old grip includes interim rope 0000 195 8200 (3 x 800 mm); the new grip includes the final rope. Summary rows 4–7 preserve these assembly contents.
  • The old grip and interim rope remain available for other models. Full starter modifications also apply to BG 72, BG 75, FC 72, FS 72, FS 74, FS 76, HS 75, HS 80 and HS 85. HS 72, HS 74 and HS 76 are deliberately excluded from this grip note: their subsection list omits 2.2.
  • The section 2.6 interchangeability statement belongs to this starter update; it does not remove the explicit model/subsection limitation or the separate control-handle retrofit conditions.
  • These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.

Part numbers (4)
  • 0000 190 3400 — ElastoStart grip with interim ropePrevious; retained for other models · Named section 2 models only; see conditions
  • 0000 190 3403 — ElastoStart grip with final ropeNew · Named section 2 models only; see conditions
  • 0000 195 8200 — Starter rope 3 x 800 mmOld grip content · Named section 2 models only; see conditions
  • 4137 195 8200 — Starter rope 2.7 x 910 mmNew grip content · Named section 2 models only; see conditions

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76

TI24/2002: rope rotor and spring supplied as an assembly

Preserve the interim-rotor availability conflict; new rotor and spring are not separate spares.

  • Original rope rotor 4133 195 0400 was replaced by interim rotor 4133 195 0470. The TI says the interim rotor is no longer available separately and the rewind spring 4133 195 1600 is likewise supplied only as part of rope rotor with rewind spring 4137 190 1100. The new assembly contains the rotor and spring; no independent new numbers are given for either component.
  • The starter drawing labels rope (1), ElastoStart grip (2), rotor (3), spring (4), and rotor/spring assembly (5). These are not the summary-table row numbers: assembly 4137 190 1100 is summary item 8, with its spring and rotor as items 9 and 10.
  • Preserved source tension: prose and summary remark 4 say the interim rotor is no longer available from the factory, while summary item 10 (previous rotor 4133 195 0470) carries remark 3 permitting previous stock until exhausted. Spring item 9 also carries the stock remark despite prose saying it is no longer separate. New separate items are explicitly unavailable under remark 6; use assembly item 8. Do not silently collapse these phase/stock statements into a current availability promise.
  • Section 2.7 explicitly extends subsections 2.3–2.5, as well as rope subsection 2.1, to HS 72, HS 74 and HS 76. The broader group receives all starter modifications. Section 2.6 states full interchangeability with previous versions within this starter scope, not a control-handle equivalence rule. All other parts are stated unchanged.
  • These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.

Part numbers (4)
  • 4133 195 0400 — Rope rotorOriginal; stocks-only phase · Named section 2 models only; see conditions
  • 4133 195 0470 — Rope rotorInterim; conflicting separate-stock statements · Named section 2 models only; see conditions
  • 4133 195 1600 — Rewind springPrevious separate part; stock/assembly statements retained · Named section 2 models only; see conditions
  • 4137 190 1100 — Rope rotor with rewind springNew assembly; includes both components · Named section 2 models only; see conditions

Historical fitment · FC 72

FC 72: asymmetric muffler pattern and corrected outlet orientation

New slotted gasket, insert and cover fit either pattern; old pieces need modification for the new muffler.

X 26 985 789 — Asymmetric muffler-hole pattern only; screw length change is separately in progress.

  • From X 26 985 789, muffler 4133 140 0605 → 4133 140 0606 moves the upper-left mounting hole about 2.5 mm (0.10 in) left to enforce cover orientation. New exhaust gasket 4133 149 0601, insert 4133 145 1001 and cover 4133 145 0601 have that mounting point slotted and can be used with both original and new parts.
  • When replacing the original muffler with the new version, either modify the original gasket/insert/cover or install the new versions. The bulletin provides no complete machining procedure; do not infer an unrestricted old-cover fit on the new muffler. Original gasket 4133 149 0600, insert 4133 145 1000, cover 4133 145 0600 and muffler are while-stocks-last.
  • For ORIGINAL muffler/insert/cover assembly, cover outlet must face the rewind starter and the insert short tube must face the fan housing. The bulletin explicitly corrects insert orientation in printed parts list 1993-07 and microfiche 1993-02; those older drawings are not assembly authority.
  • Gasket set 4133 007 1050 → 4133 007 1051 includes exhaust gasket key 2. Only the new gasket set is available; old set no longer supplied. All other parts remain as before.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 7 · TI 5/1994, p. 8 — asymmetric muffler pattern and corrected outlet orientation.

Part numbers (10)
  • 4133 140 0605 — Muffleroriginal · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 140 0606 — Mufflernew · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 149 0600 — Exhaust gasketoriginal · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 149 0601 — Exhaust gasketnew · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 145 1000 — Insertoriginal · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 145 1001 — Insertnew · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 145 0600 — Cover plateoriginal · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 145 0601 — Cover platenew · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 007 1050 — Gasket setoriginal · FC 72 — asymmetric muffler pattern and corrected outlet orientation
  • 4133 007 1051 — Gasket setnew · FC 72 — asymmetric muffler pattern and corrected outlet orientation

Historical fitment · FC 72

FC 72: cover screws lengthen to M4×12

9022 313 0660 replaces M4×6 screw 9022 313 0610 for this cover.

  • Cover plate mounting changes from IS-M4×6 screw 9022 313 0610 to IS-M4×12 screw 9022 313 0660 to standardize with FS/HS 72/74/76 and BG 72. The old screw remains available as a spare.
  • Section 4.2 introduction is “in progress”; do not copy the section 4.1 muffler serial cutoff to the longer screws. No tightening torque or fastener count is supplied, and MOQ 10 is not an assembly count.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 8 — cover screws lengthen to M4×12.

Part numbers (2)
  • 9022 313 0610 — IS-M4×6 original cover screworiginal · FC 72 — cover screws lengthen to M4×12
  • 9022 313 0660 — IS-M4×12 cover screwnew · FC 72 — cover screws lengthen to M4×12

IPL correction · FC 72

FC 72: clockwise starter spring and leg orientation

Use 0000 998 0612, not counterclockwise 0000 998 0609, on FC 72.

  • The bulletin corrects the parts-list illustration: clockwise spring 0000 998 0612 belongs on FC 72 (direction viewed looking at carrier). Its assignment table also names FS 72/74/76; counterclockwise 0000 998 0609 belongs to the historical FS 48/52/56/66 group. This FC 72 note does not attach to later unrelated FS 56 series or establish their rotation.
  • When fitting 0612 on pawl 4133 195 7200, the SHORT leg rests against the side of the pawl. AFTER installation, the LONG leg rests against the carrier inner wall. The original drawing identifies pawl 1, short leg 2 and long leg 3. This is an assembly correction, not a dated introduction or authorization to run the engine.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 11 · TI 5/1994, p. 12 — clockwise starter spring and leg orientation.

Part numbers (3)
  • 0000 998 0612 — Clockwise torsion spring for FC 72required · FC 72 — clockwise starter spring and leg orientation
  • 0000 998 0609 — Counterclockwise spring, NOT for FC 72excluded alternative · FC 72 — clockwise starter spring and leg orientation
  • 4133 195 7200 — Starter pawl receiving clockwise springinstallation companion · FC 72 — clockwise starter spring and leg orientation

Historical fitment · FC 72 / FS 72 / FS 74 / FS 76

FC 72 / FS 72 / FS 74 / FS 76: ElastoStart special-accessory retrofit

0000 190 3400 includes required 3 x 800 mm rope 0000 195 8200.

  • The new ElastoStart is offered with immediate effect as a SPECIAL ACCESSORY, not stated standard production equipment. No changes to the rewind starter are necessary to retrofit it, but installation differs slightly from the standard grip. No serial cutoff or verified production date is supplied.
  • The page 3 spare table lists complete ElastoStart 0000 190 3400 INCLUDING item 1, starter rope 0000 195 8200, dimension 3 x 800 mm. Item 1 here is a spare-table position, not construction drawing item 1 (grip). No separate internal component ordering numbers or additional quantity claims are printed.
  • Printed model-series assignment: FC 72 and FS 72/74/76 — 4133.
  • Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.

Source: TI 7/1996, p. 1 · TI 7/1996, p. 3 — FC 72 / FS 72 / FS 74 / FS 76: ElastoStart special-accessory retrofit.

Part numbers (2)
  • 0000 190 3400 — ElastoStart complete assemblyincludes item 1 starter rope · FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
  • 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only

Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76

ElastoStart construction and force path: spring-label conflict retained

Spring cushioning is qualitative; the function paragraph calls the spring (3), but the key and drawing use (4).

  • Construction key: 1 grip, 2 cap, 3 sleeve, 4 helical spring, 5 washer, 6 starter rope. The drawing shows upper and lower washers both labeled 5. In the relaxed position the sleeve, spring and washers are retained by stop lug 7. These are component labels, not independently supplied spare numbers.
  • During cranking the described load path is grip 1 → lower washer 5 → helical spring → upper washer 5 → sleeve 3 → rope 6. Engine compression compresses the spring and its peaks are cushioned. The printed function paragraph says helical spring (3), although its opening paragraph, page 1 key and both drawings assign spring 4 and sleeve 3. This source contradiction remains explicit; the immutable text is not rewritten.
  • After the first compression stroke the source describes grip force as practically uniform. Above an unspecified spring-determined starting-force level the spring becomes fully compressed and effort transfers directly from grip to rope. No force threshold, spring rate, travel limit or replacement spring specification is given.
  • Page 1 plots tensile force versus hand travel, with thick ElastoStart and thin standard-grip curves. Axes have no numerical values; the illustration is qualitative and does not establish a percentage reduction. Construction differs from the chainsaw version referenced in TI 29/1992; that TI is outside the retained inventory. No missing chainsaw construction or interchange claim is imported; current construction is fully described here.
  • The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
  • Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.

Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 — ElastoStart construction and force path: spring-label conflict retained.

No additional parts-table entry added.

Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76

ElastoStart repair limit: rope only, otherwise complete assembly

The cutaway is not permission to repair the grip internals.

  • Repairs are LIMITED TO REPLACEMENT OF THE STARTER ROPE. A faulty ElastoStart can only be replaced as a COMPLETE ASSEMBLY. The cutaway and named spring/sleeve/washers explain function, not approved internal repair or separately available components.
  • For this accessory the complete assembly is 0000 190 3400 and the only separately listed replacement is rope 0000 195 8200. No spring substitute, preload setting or procedure to rebuild the grip is supplied.
  • The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
  • Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.

Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart repair limit: rope only, otherwise complete assembly.

Part numbers (2)
  • 0000 190 3400 — ElastoStart complete assemblyincludes item 1 starter rope · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only
  • 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only

Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76

ElastoStart installation: outside-in guide threading and rotor knot

The two installation steps require a simple overhand knot at the rope rotor.

  • For installing ElastoStart WITH STARTER ROPE: thread the rope through the rope-guide bushing FROM OUTSIDE the starter housing. Then thread the rope into the rope rotor and secure it with a SIMPLE OVERHAND knot. Page 2 shows the guide/rotor route and knot; it does not prescribe a different multi-loop knot.
  • These are accessory-specific installation changes, not a complete rewind-starter overhaul. No rotor pretension turn count, fastener torque or universal winding direction is printed; none is inferred from the arrow or from another model. The separate page 3 grip knot applies when replacing the rope.
  • The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
  • Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.

Source: TI 7/1996, p. 1 · TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart installation: outside-in guide threading and rotor knot.

Part numbers (1)
  • 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only

Service note · BG 72 / FC 44 / FS 36 / FS 40 / FS 44 / FC 72 / FS 72 / FS 74 / FS 76

ElastoStart rope replacement: mandatory 8200 rope and grip knot

Ease off cap, remove old rope, fit 0000 195 8200 with simple overhand grip knot, refit cap.

  • Four printed steps: ease the cap off the starter grip; remove remaining rope from grip AND rope rotor; fit starter rope 0000 195 8200 in the same way as the standard rope, but secure it IN THE GRIP only with a SIMPLE OVERHAND knot; refit the cap in the grip. The drawing shows cap removal and rope/knot insertion into the grip.
  • The source says rope 0000 195 8200 MUST be used to guarantee correct ElastoStart operation; its listed dimension is 3 x 800 mm. Matching diameter/length alone is not evidence that a substitute rope is approved. Page 2 separately requires a simple overhand knot at the rotor.
  • The same-as-standard instruction refers to the base starter operation; this note preserves the complete accessory-specific delta, not a standalone base-starter repair manual. No extra winding count, trimming allowance or rope material specification is invented.
  • The TI header prints BG 72 as series 4227, while the retained exact-model BG 72 rewind-starter IPL is cataloged under 4133 (4227 has BG 75). The BG 72 link is exact-model navigation only: this unresolved series conflict is not silently corrected and does not establish BG 75 fitment or equivalence of series.
  • Historical TI 07/1996 guidance for BG 72, FC 44, FC 72, FS 36, FS 40, FS 44, FS 72, FS 74 and FS 76 only. No later variant, chainsaw or other shared-sheet model is included. No hardware operation was performed; availability and comfort claims are historical, not current stock or a measured project result.

Source: TI 7/1996, p. 2 · TI 7/1996, p. 3 — ElastoStart rope replacement: mandatory 8200 rope and grip knot.

Part numbers (1)
  • 0000 195 8200 — Starter rope 3 x 800 mmrequired rope; included item 1 · BG 72, FC 44, FS 36, FS 40, FS 44, FC 72, FS 72, FS 74, FS 76; TI07/1996 ElastoStart only

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85 / BG 72 / FC 72 / FS 48 / FS 52 / FS 56 / FS 62 / FS 66 / FS 72 / FS 74 / FS 76 / HS 72 / HS 74 / HS 76

ElastoStart replacement rope: original-number conflict retained

New 0000 195 8200 is3.0×800 mm; prose and table disagree on the original.

continuously — Continuous introduction; no numeric boundary supplied for this particular change.

  • Section 3 prose prints ORIGINAL 4123 190 4000 (2.7×900 mm), replaced for some time by ELASTOSTART 0000 195 8200 (3.0×800 mm). The summary instead prints ORIGINAL 4123 195 8200. Both are confirmed on the original scan: retain the UNRESOLVED NUMBER CONFLICT, not an OCR correction, proven equivalence or two-step supersession.
  • In addition to cover models, the source explicitly extends this change to BG 72, FC 72, FS 48/52/56/62/66/72/74/76 and HS 72/74/76. These are the historical configurations: not the later type 4144 FS 56 or type 4112 FS 80.
  • Modification introduced CONTINUOUSLY; summary remark says ORIGINAL NO LONGER AVAILABLE FROM FACTORY. No machine-number cutoff, handle assembly replacement, knot procedure or permission to shorten either rope to an unprinted length is given. Catalog associations expose the historical note without rewriting their rope rows or choosing which conflicting original is correct.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 5 — Entire section 3 prose, extended model list, summary and availability remark.

Part numbers (3)
  • 4123 190 4000 — Original rope number printed in prose;2.7×900 mmConflicts with summary original · Only the named TI 41/1997 configurations and conditions
  • 4123 195 8200 — Original rope number printed in summaryConflicts with prose original · Only the named TI 41/1997 configurations and conditions
  • 0000 195 8200 — ElastoStart rope;3.0×800 mmReplacement · Only the named TI 41/1997 configurations and conditions

Wrong number or missing part for the FC 72? Report a correction →