← Edgers & other equipment · series 4133

Stihl 4133 · Section A · 1 of 9 · 25 parts

Crankcase, Cylinder

Fits FC 72.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112121314141516171819220334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (25)

PosPart numberDescriptionQty
1 4133 020 2801 Crankcase, starter side Fitment / change note → 1
2 9380 620 2570 Roll pin 5x12 2
3 9503 003 0242 Grooved ball bearing 6201 2
4 9640 003 1195 Oil seal 12x22x5 2
5 4133 020 2601 Crankcase, fan side Fitment / change note → 1
6 4133 030 0400 Crankshaft 1
7 9022 341 1050 Spline screw IS-M5x25 3
8 4133 022 0501 Cylinder Ø 33mm 1
9 4133 034 0500 Piston Ø 33 mm 1
10 4133 034 3000 Piston ring Ø 33x1.5 mm 2
11 4112 034 1500 Piston pin 1
12 9463 650 0805 Snap ring 8x0.7 2
13 9512 004 1820 Needle cage 8x11x10 1
14 4133 036 8901 Thrust washer 2
15 4133 029 2300 Cylinder gasket 1
16 9022 371 1020 Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 2
17 4133 084 2200 Guard 1
18 0000 400 7000 Spark plug NGK BPMR7A 1
18 1110 400 7005 Spark plug Bosch WSR 6 F 1
19 0000 998 0606 Torsion spring 1
20 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
Not numbered on the diagram — assemblies, kits and options
— 4133 020 1201 Cylinder with piston Ø 33 mm Fitment / change note → 1
— 4133 030 2000 Piston Ø 33 mm 1
— 4133 007 1051 Set of gaskets 1
— 0783 830 2000 Tube of sealant Dirko HT red not illustrated 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FC 72

FC 72: grooved crankcase halves and slotted shroud

Old and new crankcase halves and shroud may be used in any combination on FC 72.

X 26 846 088 — FC 72 grooved crankcase and slotted shroud introduction only.

  • From X 26 846 088, fan-side crankcase 4133 020 2600 → 4133 020 2601, starter-side crankcase 4133 020 2800 → 4133 020 2801 and shroud 4133 084 0900 → 4133 084 0901. Each new crankcase half has an integral ledge with groove; the shroud has an extra slot parallel to its lower edge, identified by arrows in the original drawings.
  • The bulletin explicitly permits all old/new combinations ON FC 72. The mention of modifications to some FS 72/74/76 executions does not grant that same unrestricted combination rule to those brushcutters. Old versions are supplied only until factory stocks are exhausted, then new versions as replacements.
  • Historical English TI05/1994, series 4133 FC 72 only. Shared-series catalog grouping and references to standardization do not extend these cutoffs or restrictions to other models. Historical availability is not current stock. MOQ columns are commercial order quantities, not installation counts. No physical interchange test was performed.

Source: TI 5/1994, p. 1 · TI 5/1994, p. 2 — grooved crankcase halves and slotted shroud.

Part numbers (6)
  • 4133 020 2600 — Fan-side crankcaseoriginal · FC 72 — grooved crankcase halves and slotted shroud
  • 4133 020 2601 — Fan-side crankcasenew · FC 72 — grooved crankcase halves and slotted shroud
  • 4133 020 2800 — Starter-side crankcaseoriginal · FC 72 — grooved crankcase halves and slotted shroud
  • 4133 020 2801 — Starter-side crankcasenew · FC 72 — grooved crankcase halves and slotted shroud
  • 4133 084 0900 — Shroudoriginal · FC 72 — grooved crankcase halves and slotted shroud
  • 4133 084 0901 — Shroudnew · FC 72 — grooved crankcase halves and slotted shroud

Service note · FC 72

FC 72: coupled engine power increase and repair restrictions

About 15% more power to 0.8 kW (1.1 bhp) requires all new parts when upgrading the original version.

X 31 578 923 — FC 72 engine power-increase introduction only; not FS 74/FS 76 cutoffs.

  • From X 31 578 923, FC 72 power increases by approximately 15% to 0.8 kW (1.1 bhp). Changes are port timing, compression, intake cross-section, transfer-port shape, gasket and spacer-flange shape. No new displacement or universal output guarantee is given.
  • New cylinder, gasket and spacer versions are generally used as replacement parts. Repairs to NEW-VERSION machines require ONLY NEW-TYPE parts; otherwise reduced power and malfunctions are expected. Original machines reach the claimed higher power only if ALL NEW PARTS are installed. A new gasket alone is not the complete power upgrade.
  • Exact scope is FC 72, not FS 72 or every 4133 machine. Shared numbers and similar FS 74/FS 76 instructions do not transfer their changeovers or unprinted installation details to this edger.
  • Historical TI 46/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 46/1994, p. 1 · TI 46/1994, p. 2 · TI 46/1994, p. 3 — coupled engine power increase and repair restrictions.

No additional parts-table entry added.

Service note · FC 72

FC 72: new cylinder geometry and mandatory longer screws

The new cylinder always uses M5×20 screws tightened to 10 Nm, not the original M5×16 screws.

X 31 578 923 — FC 72 engine power-increase introduction only; not FS 74/FS 76 cutoffs.

  • Cylinder base flange is approximately 3 mm thicker and intake cross-section larger. Figure 356TI001 compares old/new dimensions 7/10, 15/19 and 9/10.5 mm. These cylinder drawing dimensions are NOT the gasket window widths 16/19 mm. No unprinted machining instructions are inferred.
  • Old cylinder with piston 4133 020 1200 becomes 4133 020 1201 (includes 1–2); cylinder 4133 022 0500 becomes 4133 020 1250 (key 1, includes 2). Both new cylinder rows have MOQ 1; original cylinder versions are no longer available from factory (remark 1). Other cylinder parts remain as before.
  • Original IS-M5x16 screws 9022 341 0980 (2x) have no new-column counterpart and remain available (remark 2). New IS-M5x20 screws 9022 371 1020 (key 2, 2x) have MOQ 10. Two installed screws is not MOQ 10. New cylinder MUST use the supplied M5x20 screws IN ALL CASES; cylinder tightening torque 10 Nm. This does not supply a torque for spacer through-screws.
  • The new cylinder and cylinder-with-piston were to be supplied with M5x20 screws for APPROXIMATELY THREE YEARS. This is a historical inclusion period, not proof that a current or loose cylinder comes with screws.
  • Historical TI 46/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.

Source: TI 46/1994, p. 1 · TI 46/1994, p. 2 · TI 46/1994, p. 3 — new cylinder geometry and mandatory longer screws.

Part numbers (6)
  • 4133 020 1200 — Original cylinder with pistonno longer factory available · FC 72 only in the version/configuration described here
  • 4133 020 1201 — New cylinder with pistonMOQ 1; includes 1–2 · FC 72 only in the version/configuration described here
  • 4133 022 0500 — Original cylinderno longer factory available · FC 72 only in the version/configuration described here
  • 4133 020 1250 — New cylinder; key 1MOQ 1; includes 2 · FC 72 only in the version/configuration described here
  • 9022 341 0980 — Original IS-M5x16 screw; 2xremains available · FC 72 only in the version/configuration described here
  • 9022 371 1020 — New IS-M5x20 screw; key 2, 2xMOQ 10; mandatory with new cylinder · FC 72 only in the version/configuration described here

Wrong number or missing part for the FC 72? Report a correction →