Stihl 4133 · Section A · 1 of 16 · 25 parts
Crankcase, Cylinder
Fits FS 72, FS 74, FS 76.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 020 2801 | Crankcase, starter side | 1 |
| 2 | 9380 620 2570 | Roll pin 5x12 | 2 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 2 |
| 4 | 9640 003 1195 | Oil seal 12x22x5 | 2 |
| 5 | 4133 020 2601 | Crankcase, fan side | 1 |
| 6 | 4133 030 0400 | Crankshaft | 1 |
| 7 | 9022 341 1050 | Spline screw IS-M5x25 | 3 |
| 8 | 4133 022 0501 | Cylinder Ø 33mm Fitment / change note → | 1 |
| 9 | 4133 034 0500 | Piston Ø 33 mm | 1 |
| 10 | 4133 034 3000 | Piston ring Ø 33x1.5 mm | 2 |
| 11 | 4112 034 1500 | Piston pin | 1 |
| 12 | 9463 650 0805 | Snap ring 8x0.7 | 2 |
| 13 | 9512 004 1820 | Needle cage 8x11x10 | 1 |
| 14 | 4133 036 8901 | Thrust washer Fitment / change note → | 2 |
| 15 | 4133 029 2300 | Cylinder gasket | 1 |
| 16 | 9022 371 1020 | Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 17 | 4133 084 2200 | Guard | 1 |
| 18 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 18 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 19 | 0000 998 0606 | Torsion spring | 1 |
| 20 | 1106 405 1000 | Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4133 020 1201 | Cylinder with piston Ø 33 mm Fitment / change note → | 1 |
| — | 4133 030 2000 | Piston Ø 33 mm | 1 |
| — | 4133 007 1051 | Set of gaskets | 1 |
| — | 0783 830 2000 | Tube of sealant Dirko HT red not illustrated | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: connecting-rod washers replace only as sets
Two 4133 036 8900 washers → 4133 036 8901; printed small-end/big-end wording conflicts.
- The opening text places TWO thrust washers between the piston and the connecting-rod small end; the exploded drawing arrows point to those washers. It gives 4133 036 8900 → 4133 036 8901 from machine No. X 24 736 885. This scoped component threshold is not a model-identification range.
- The source says the original and new washers are not interchangeable, then explicitly requires replacement in SETS. Do not mix one old and one new washer or infer unrestricted individual interchange. The original version is no longer available from the factory.
- Printed wording conflict: the service note says to replace the old washers with 4133 036 8901 when servicing the BIG END, while the opening text and drawing locate the washers at the SMALL END. Both statements are present in the original scan. The trigger/location wording remains unresolved; it is not silently corrected into a different repair instruction. No washer thickness, axial clearance or torque is given.
- Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 8 — FS 72, FS 74, FS 76: connecting-rod washers replace only as sets.
Part numbers (2)
- 4133 036 8900 — Original thrust washer, two per assemblyoriginal · FS 72, FS 74, FS 76: connecting-rod washers replace only as sets
- 4133 036 8901 — New thrust washer; replace the pair as a setreplacement-set · FS 72, FS 74, FS 76: connecting-rod washers replace only as sets
Service note · FS 74 / FS 76
FS 74 / FS 76: coupled 0.8 kW engine upgrade
Approximate 15% power increase requires all new parts when upgrading the original version.
FS 74: X 29 049 102; FS 76: X 29 034 635 — Model-specific introduction numbers;not one combined serial range and not FS72 applicability.
- The TI states an approximately 15% increase to 0.8 kW (1.1 bhp), achieved by changed port timing, increased compression, enlarged intake cross-section, changed transfer-port shapes and changed gasket/spacer-flange shapes. These are source claims, not bench measurements or instructions to grind ports.
- The new cylinder, gasket and spacer flange are generally used as replacement parts. For NEW-VERSION machines ONLY NEW-TYPE replacement parts may be used; otherwise power deterioration and malfunctions are expected. An ORIGINAL-VERSION machine reaches the stated approximately 0.8 kW only if ALL NEW PARTS are installed. A gasket-only substitution is not the complete power upgrade.
- FS 74 introduction is X 29 049 102; FS 76 is X 29 034 635. These model-specific cutoffs must not be swapped or collapsed into a universal range. FS 72 is NOT named, despite sharing 4133 IPL sheets. The retained 44.94 identifier is separate from the printed January 13, 1995 publication date; D1/MTK-na. Prior TI 01.94 is provenance only.
- Historical TI 44/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 44/1994, p. 1 · TI 44/1994, p. 2 · TI 44/1994, p. 3 — coupled 0.8 kW engine upgrade.
No additional parts-table entry added.
Service note · FS 74 / FS 76
FS 74 / FS 76: thicker cylinder flange needs M5x20 screws
New cylinder mounting always uses M5x20 screws at 10 Nm; the old screws are shorter.
FS 74: X 29 049 102; FS 76: X 29 034 635 — Model-specific introduction numbers;not one combined serial range and not FS72 applicability.
- New cylinder base flange is approximately 3 mm thicker and its intake cross-section is larger. Figure 356TI001 gives old/new flange heights 7/10, intake widths 15/19 and vertical opening dimensions 9/10.5. These drawing dimensions are not gasket-window widths (16/19 mm) or machining instructions.
- New cylinder MUST IN ALL CASES use the supplied M5x20 screws; tightening torque 10 Nm. This torque is for CYLINDER MOUNTING, not the M5x25 spacer screws or M5x56 through screws. Original cylinder used M5x16.
- Cylinder-with-piston 4133 020 1200 becomes 4133 020 1201 (includes table 1, 2); cylinder 4133 022 0500 becomes 4133 020 1250 (key 1, includes 2). Both new units MOQ 1; both originals no longer available from factory (remark 1). Other parts remain as before.
- Two old IS-M5x16 screws 9022 341 0980 remain available (remark 2). Two new IS-M5x20 screws 9022 371 1020 are key 2, MOQ 10; 2x is installation quantity. The source promises supplied longer screws with replacement cylinder/cylinder-with-piston for APPROXIMATELY THREE YEARS, not indefinitely or current kit contents.
- Historical TI 44/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 44/1994, p. 1 · TI 44/1994, p. 2 · TI 44/1994, p. 3 — thicker cylinder flange needs M5x20 screws.
Part numbers (6)
- 4133 020 1200 — Original cylinder with pistonno longer factory available · FS 74 / FS 76 only in the version/configuration described here
- 4133 020 1201 — New cylinder with piston; includes 1, 2MOQ 1 · FS 74 / FS 76 only in the version/configuration described here
- 4133 022 0500 — Original cylinderno longer factory available · FS 74 / FS 76 only in the version/configuration described here
- 4133 020 1250 — New cylinder; key 1, includes 2MOQ 1 · FS 74 / FS 76 only in the version/configuration described here
- 9022 341 0980 — IS-M5x16 screw; 2xoriginal remains available · FS 74 / FS 76 only in the version/configuration described here
- 9022 371 1020 — IS-M5x20 screw; key 2, 2xMOQ 10; 10 Nm cylinder mounting · FS 74 / FS 76 only in the version/configuration described here
Conditional replacement · FS 72
FS 72: uprated cylinder requires longer screws and all Plus parts
About 15% more power to 0.8 kW requires ALL new Plus components; new cylinder always uses two M5x20 screws at 10 Nm.
- The TI states an approximate 15% engine-power increase to 0.8 kW (1.1 bhp), achieved by changed port timing, increased compression, enlarged intake cross-section, changed transfer-port shape, gasket and spacer flange. It supplies no compression ratio or port timing angles; these are design claims, not measured output or machining instructions.
- New cylinder 4133 022 0501 replaces 4133 022 0500; old cylinder no longer available from factory (remark 1), new MOQ 1. Base flange is approximately 3 mm thicker and intake section larger. Drawing 356TI001 compares original LEFT/new RIGHT: intake widths 15/19, base-flange heights 7/10, and intake heights 9/10.5 as printed. The drawing has no tolerance or standalone unit legend; contextual millimetres are not a manufacturing specification.
- New cylinder MUST ALWAYS use TWO IS-M5x20 screws 9022 371 1020, tightening torque 10 Nm. Old TWO IS-M5x16 screws 9022 341 0980 are not used with the new cylinder but remain available (remark 2). New screw MOQ 10 is an ordering minimum, not ten installed screws. The 10 Nm applies to the cylinder mounting, not every screw in this bulletin.
- ONLY new-type replacement parts may be used when repairing NEW-version machines, otherwise reduced power and malfunctions are expected. An ORIGINAL-version machine reaches approximately 0.8 kW only if ALL new parts are installed. Page 3 repeats: when changing Non-Plus Series to Plus Series, use ALL new Plus Series components. No partial-conversion power promise.
- Introduction is “in progress”; no serial cutoff is supplied. “Near future” and footer date are not an exact production date. The shared FS72/74/76 IPL sheet is navigation only: this TI names FS72 alone and does not establish an FS74/FS76 or BG72/FC72 upgrade.
- Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.
Source: TI 12/1995, p. 1 · TI 12/1995, p. 2 · TI 12/1995, p. 3 — All three pages: power/cylinder, gasket/spacer/service conditions, Plus Series note and complete summary.
Part numbers (4)
- 4133 022 0500 — Original cylinderno longer available from factory · FS 72; stated TI conditions
- 4133 022 0501 — New cylinder; key 1MOQ 1; Plus conversion conditions · FS 72; stated TI conditions
- 9022 341 0980 — Original IS-M5x16 screws; tworemain available; not for new cylinder · FS 72; stated TI conditions
- 9022 371 1020 — New IS-M5x20 screws; key 2; twomandatory for new cylinder;10 Nm; MOQ 10 · FS 72; stated TI conditions
Wrong number or missing part for the FS 72, FS 74, FS 76? Report a correction →