Stihl 4133 · Section C · 3 of 16 · 25 parts
Ignition system, Clutch
Fits FS 72, FS 74, FS 76.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4112 036 8600 | Woodruff key | 1 |
| 2 | 4133 400 1200 | Flywheel Fitment / change note → | 1 |
| 3 | 4133 400 1301 | Ignition module Fitment / change note → | 1 |
| 4 | not sold separately | Ignition lead 175 mm not available as a separate item | 1 |
| 5 | 0000 989 1012 | Grommet | 1 |
| 6 | 4133 405 8001 | Insulator | 1 |
| 7 | 4133 442 0400 | Insulating hose | 1 |
| 8 | 9022 371 0710 | Spline screw IS-M4x20 | 2 |
| 9 | 4133 160 2020 | Clutch Fitment / change note → | 1 |
| 10 | 4133 162 7900 | Tension spring Fitment / change note → | 2 |
| 11 | 4133 080 1800 | Fan housing | 1 |
| 12 | 4133 352 8105 | Insert | 2 |
| 13 | 4133 160 2900 | Clutch drum | 1 |
| 13 | 4133 160 2920 | Clutch drum | 1 |
| 14 | 9455 621 1130 | Circlip 12x1 | 1 |
| 15 | 4123 791 9300 | Rubber insert | 1 |
| 16 | 9457 621 4481 | Circlip | 1 |
| 17 | 4133 790 7200 | Sleeve | 1 |
| 17 | 4123 790 7200 | Sleeve | 1 |
| 18 | 9074 478 4125 | Pan head self-tapping screw IS-5x14 | 1 |
| 19 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
| 20 | 9022 341 0980 | Spline screw IS-M5x16 | 3 |
| 21 | 4114 432 9201 | Grommet | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · FS 72 / FS 74 / FS 76
FS 72 / FS 74 / FS 76: series 4133 replacement ignition assignment
4133 400 1301 with flywheel 4133 400 1200; 175 mm ignition lead.
- Printed series 4133. Use 4133 400 1301 with flywheel 4133 400 1200.
- Printed ignition-lead length: 175 mm (6 7/8 in). Preserve both printed units.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4133 400 1301 — Replacement ignition moduleAssigned component · FS 72 / FS 74 / FS 76, printed series 4133, listed combination only
- 4133 400 1200 — Assigned flywheelRequired pairing · FS 72 / FS 74 / FS 76, printed series 4133
Service note · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: modified clutch carrier and two-dot shoes
Clutch 4133 160 2000 keeps its number; complete-assembly replacement only.
- Carrier and clutch shoes change to optimize clutch performance. Only the complete clutch is supplied as a spare; the bulletin says this change does not affect complete-clutch exchangeability. This is not permission to mix individual carrier/shoe versions.
- The modified shoes have two dots each (B); the assignment table gives one dot for the original version. Wrench engagement A changes from 14 mm (9/16 in) to 10 mm (13/32 in). These are engagement dimensions, not wrench opening sizes.
- Page 3 section 1.4 assigns the carrier change to FS 72 from X 24 929 968, FS 74 from X 24 934 457 and FS 76 from X 24 942 579. Page 2 instead prints FS 74 AGAIN for X 24 942 579. This model-label conflict is retained, not silently corrected or converted to a universal serial rule; check actual clutch geometry.
- Unmodified clutch 4133 160 2000 is supplied until existing factory stocks are exhausted. This carrier change is separate from the later lined clutch 4133 160 2020.
- Historical English TI 01/1994, sections 1–4 only. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 1 · TI 1/1994, p. 2 · TI 1/1994, p. 3 — FS 72, FS 74, FS 76: modified clutch carrier and two-dot shoes.
Part numbers (1)
- 4133 160 2000 — Complete clutch; number unchanged for carrier modificationunchanged-number · FS 72, FS 74, FS 76: modified clutch carrier and two-dot shoes
Service note · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: clutch wrench replacement is one-way compatible
4133 893 1301 works with both clutch versions; 4133 893 1300 only with the original.
- The new wrench 4133 893 1301 is required for the modified carrier and can also service the original clutch. The old 4133 893 1300 cannot be used on the modified carrier; they are NOT completely interchangeable.
- Old wrench opening SW: 13 mm (1/2 in); new SW: 17 mm (43/64 in). Old clutch engagement A: 14 mm (9/16 in), one dot B; modified A: 10 mm (13/32 in), two dots B. Figure 1 is the old wrench and figure2 the new.
- Page 2 lists FS 72 from X 24 929 968, FS 74 from X 24 934 457, then repeats FS 74 at X 24 942 579. Page 3 assigns that last carrier threshold to FS 76. The conflict remains unresolved; the wrench selection follows actual carrier geometry, not a silently repaired label.
- The wrench replacement is in progress; the original wrench is supplied only until factory stocks are exhausted. No tightening torque is stated.
- Historical English TI 01/1994, sections 1–4 only. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 1 · TI 1/1994, p. 2 · TI 1/1994, p. 3 — FS 72, FS 74, FS 76: clutch wrench replacement is one-way compatible.
Part numbers (2)
- 4133 893 1300 — Original clutch wrench, SW 13original-tool · FS 72, FS 74, FS 76: clutch wrench replacement is one-way compatible
- 4133 893 1301 — Replacement clutch wrench, SW 17replacement-tool · FS 72, FS 74, FS 76: clutch wrench replacement is one-way compatible
Service note · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: lined clutch replaces complete assemblies, not individual shoes
4133 160 2000 → 4133 160 2020; FS 76 production change differs from FS 72/74 spares.
- Only FS 76 production changes to lined shoes from X 26 768 543. FS 72 and FS 74 continue with unlined shoes in production. The new lined complete clutch is nevertheless supplied as a replacement for all three models.
- Clutch 4133 160 2020 includes two clutch shoes (item 1) and two springs (item 2). Individual shoes are not available separately; do not infer a shoe part number from the complete clutch.
- Spring hooks are modified so spring 4133 162 7900 works with both original and new shoes; its part number does not change. Unmodified springs are supplied until stocks are exhausted. Original complete clutch 4133 160 2000 is supplied only until stocks are exhausted.
- The page 3 drawing contrasts the unlined original at left with lining on the new shoes at right. This lining change is distinct from the earlier carrier/two-dot modification.
- Historical English TI 01/1994, sections 1–4 only. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 3 — FS 72, FS 74, FS 76: lined clutch replaces complete assemblies, not individual shoes.
Part numbers (3)
- 4133 160 2000 — Original complete clutchoriginal · FS 72, FS 74, FS 76: lined clutch replaces complete assemblies, not individual shoes
- 4133 160 2020 — Lined complete clutch; includes two shoes and two springsreplacement · FS 72, FS 74, FS 76: lined clutch replaces complete assemblies, not individual shoes
- 4133 162 7900 — Clutch spring, two per clutch; hook change without number changeunchanged-number · FS 72, FS 74, FS 76: lined clutch replaces complete assemblies, not individual shoes
Wrong number or missing part for the FS 72, FS 74, FS 76? Report a correction →