Stihl 4133 · Section D · 4 of 16 · 32 parts
Air filter, Fuel tank
Fits FS 72, FS 74, FS 76.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 129 0902 | Gasket Fitment / change note → | 1 |
| 2 | 9007 319 1121 | Hexagon head screw M5x56 Fitment / change note → | 2 |
| 3 | 4133 121 1602 | Spacer flange Fitment / change note → | 1 |
| 4 | 9022 341 1050 | Spline screw IS-M5x25 | 2 |
| 5 | 4133 182 7600 | Tensioner | 1 |
| 6 | 9022 341 0980 | Spline screw IS-M5x16 | 3 |
| 7 | 9214 320 0700 | Lock nut M5 | 1 |
| 8 | 9022 313 0680 | Spline screw IS-M4x16 | 1 |
| 9 | 4114 129 0501 | Gasket | 1 |
| 10 | 4133 120 0600 | Carburetor WT-227F | 1 |
| 10 | 4226 120 0601 | Carburetor WT-329 | 1 |
| 11 | 4114 149 1205 | Gasket | 1 |
| 12 | 4133 140 2800 | Filter housing | 1 |
| 13 | 9210 261 0700 | Hexagon nut M5 Fitment / change note → | 2 |
| 14 | 4133 124 2800 | Filter | 1 |
| 15 | 4133 124 1500 | Prefilter | 1 |
| 16 | 4133 141 0500 | Filter cover | 1 |
| 17 | 4133 350 0400 | Fuel tank | 1 |
| 18 | 4133 352 8100 | Insert | 1 |
| 19 | 0000 350 3502 | Pickup body | 1 |
| 21 | 4126 358 7700 | Hose with grommet | 1 |
| 22 | 4126 358 7762 | Hose | 1 |
| 23 | 4128 350 0505 | Filler cap | 1 |
| 24 | 0000 350 0900 | Rope | 1 |
| 25 | 0000 353 0800 | Filler cap retainer | 1 |
| 26 | 4133 084 0901 | Shroud | 1 |
| 27 | 4133 967 1501 | Model plate FS 72 | 1 |
| 28 | 4133 967 1511 | Model plate FS 74 | 1 |
| 29 | 4133 967 1521 | Model plate FS 76 | 1 |
| 30 | 4133 122 6900 | Plug Fitment / change note → | 2 |
| 31 | 9291 021 0120 | Washer 5.3 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4133 007 1051 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
New cap 4133 350 0501 uses a vent hole and MIX marking; keep the vent clear.
- The old cap vents through clearance between the cap and tank-neck threads. The new cap has a dedicated vent hole, molded MIX symbol and HDPE recycling identifier. Keep the hole clear so tank pressure can equalize with atmosphere for correct carburetor operation; page 4 references TI 2.90 but does not reproduce its full contents.
- Original and new fuel caps and vent inserts can only be exchanged as assemblies. Retainer 4116 350 0900 works with both caps. Do not infer individual vent-component interchange.
- Page 5 lists old complete cap 4126 350 0502 → new 4133 350 0501 (item 1, includes items 2–4); old tank vent 4126 350 5801 → new 4133 350 5800 (item 2, includes valve item 3). Original cap is no longer factory-available; old vent is supplied while stocks last, then the COMPLETE new cap 4133 350 0501 is supplied in its place.
- New valve 4114 353 1600 is item 3; the original valve was not available separately. New sealing ring 4114 359 1200 and original gasket 4126 359 0700 are both shown at item 4; the original gasket remains a spare. Other parts stay as before. This is not a blanket standalone ring-for-gasket replacement.
- Cap change thresholds: FS 72 from X 29 794 566; FS 74 from X 26 808 493; FS 76 from X 26 772 290. Do not apply them to the separate pickup-body clip.
- Number conflict: page 4 calls 4126 350 0502 a gasket, but page 5 assigns that number to the OLD COMPLETE CAP and lists old gasket 4126 359 0700. Both original scans confirm the contradiction. No silently corrected gasket purchase number is asserted.
- Historical English TI 01/1994, sections 1–4 only. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 4 · TI 1/1994, p. 5 — FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies.
Part numbers (8)
- 4126 350 0502 — Old complete cap in page 5 table; conflicting gasket label on page 4conflicted-source · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4133 350 0501 — New complete fuel filler cap, items 2–4 includedreplacement-assembly · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4126 350 5801 — Original tank ventoriginal · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4133 350 5800 — New tank vent, includes valve item 3new-component · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4114 353 1600 — New valve, item 3new-component · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4114 359 1200 — New sealing ring, item 4new-component · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4126 359 0700 — Original gasket, item 4; remains spareretained-spare · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
- 4116 350 0900 — Retainer usable with both capsretained-component · FS 72, FS 74, FS 76: vented fuel cap and vent insert exchange only as assemblies
IPL correction · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: fuel-cap gasket position corrects the 1992 parts list
Item4 belongs BELOW tank vent item 2; the printed gasket number conflicts with the summary.
- The page 4 exploded views place item 4 below tank vent item 2. The note explicitly says the 1992-11 parts list shows the gasket in the wrong position. Preserve that assembly-order correction independently of the unresolved part-number conflict.
- Page 4 calls the gasket 4126 350 0502 (4); page 5 instead assigns 4126 350 0502 to the original COMPLETE CAP and gives original gasket 4126 359 0700 (4), with new sealing ring 4114 359 1200 also item 4. The conflict is present in the scans, not an OCR-only error; no corrected purchase number or individual gasket interchange is inferred.
- Cap and vent insert exchange only as assemblies. Retainer 4116 350 0900 works with both caps. The old/new exploded views and all callouts1–4 were reviewed; this correction does not turn the old and new item 4 parts into freely interchangeable pieces.
- Historical English TI 01/1994, sections 1–4 only. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 4 · TI 1/1994, p. 5 — FS 72, FS 74, FS 76: fuel-cap gasket position corrects the 1992 parts list.
Part numbers (3)
- 4126 350 0502 — Conflicting page 4 gasket / page 5 old-cap numberconflicted-source · FS 72, FS 74, FS 76: fuel-cap gasket position corrects the 1992 parts list
- 4126 359 0700 — Original gasket as listed on page 5source-reference · FS 72, FS 74, FS 76: fuel-cap gasket position corrects the 1992 parts list
- 4114 359 1200 — New sealing ring as listed on page 5source-reference · FS 72, FS 74, FS 76: fuel-cap gasket position corrects the 1992 parts list
Service note · FS 72 / FS 74 / FS 76
FS 72, FS 74, FS 76: pickup-body fuel-hose retention clip
Clip 4126 358 8900 improves hose retention; introduction is in progress.
- Fit clip 4126 358 8900 at the fuel-hose connection to the pickup body; the arrow in illustration 2.2 identifies the clip. The change improves security of that connection.
- Section 2.2 introduction is in progress. The serial thresholds in section 2.3 apply to the fuel CAP (2.1), not this clip. No clip installation dimension, torque or pickup-body replacement number is provided.
- Historical English TI 01/1994, sections 1–4 only. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 4 · TI 1/1994, p. 5 — FS 72, FS 74, FS 76: pickup-body fuel-hose retention clip.
Part numbers (1)
- 4126 358 8900 — Pickup-body fuel-hose retention clipnew-component · FS 72, FS 74, FS 76: pickup-body fuel-hose retention clip
Service note · FS 74 / FS 76
FS 74 / FS 76: wider intake gasket and one-way repair restriction
New 19 mm gasket can fit the old version; old parts are not permitted for new-version repairs.
FS 74: X 29 049 102; FS 76: X 29 034 635 — Model-specific introduction numbers;not one combined serial range and not FS72 applicability.
- The gas-mixture window increases from 16 mm in the old gasket to 19 mm in the new gasket (figure 356TI002). New gasket 4133 129 0902 replaces 4133 129 0900, MOQ 1; the original is supplied only while factory stocks last (remark 3).
- The NEW gasket may be installed in OLD-VERSION machines. This does NOT imply reverse interchangeability: new-version machines require new-type parts. Nor does it make the gasket alone a 0.8 kW upgrade; all new parts are required for the claimed older-machine increase. Cylinder drawing intake width 15 mm is a different feature from the old gasket window 16 mm; do not merge these dimensions.
- Historical TI 44/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 44/1994, p. 1 · TI 44/1994, p. 2 · TI 44/1994, p. 3 — wider intake gasket and one-way repair restriction.
Part numbers (2)
- 4133 129 0900 — Original 16 mm intake gasketwhile factory stocks last · FS 74 / FS 76 only in the version/configuration described here
- 4133 129 0902 — New 19 mm intake gasketMOQ 1; permitted on old version · FS 74 / FS 76 only in the version/configuration described here
Service note · FS 74 / FS 76
FS 74 / FS 76: spacer-flange installation and fastener roles
Check the entire filter-base/carburetor/flange/cylinder screw connection when fitting the new spacer to an old machine.
FS 74: X 29 049 102; FS 76: X 29 034 635 — Model-specific introduction numbers;not one combined serial range and not FS72 applicability.
- New spacer flange has a 19 mm opening on the CYLINDER-FACING SIDE. Observe the service notes when fitting it to an original-version machine; the entire filter-base / carburetor / flange / cylinder screw connection must be checked.
- Use M5x56 screws (figure 356TI003 callout 1) AND plugs 4133 122 6900 (callout 2) with the new spacer. Secure spacer to cylinder with M5x25 screws (callout 3) and A5.3 washers (callout 4). The figure shows the component stack, not permission to omit plugs or washers.
- The TI supplies NO full part numbers for the M5x25 spacer screws or A5.3 washers and NO tightening torque for either spacer/through-screw joint. The separate 10 Nm cylinder-mounting torque must not be transferred. Figure callouts 1–4 are NOT table keys 3–6; table key 3 is the spacer, while figure 3 is a screw. Complete new-part set is required for the claimed original-machine power increase.
- Historical TI 44/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 44/1994, p. 2 · TI 44/1994, p. 3 — spacer-flange installation and fastener roles.
Part numbers (2)
- 4133 121 1602 — New spacer flange; 19 mm cylinder-facing openingMOQ 1; installation restrictions · FS 74 / FS 76 only in the version/configuration described here
- 4133 122 6900 — Plugs; figure 2, table 6required with new spacer · FS 74 / FS 76 only in the version/configuration described here
Service note · FS 74 / FS 76
FS 74 / FS 76: spacer supply changes and unchanged through-fasteners
Old complete spacer assembly is replaced by a separately listed flange; through-screw, nut and plug numbers remain unchanged.
- Old spacer-flange assembly 4133 120 2202 includes table 3–6, has a dash in the new-assembly column and remains supplied only while factory stocks last (remark 3). New bare spacer 4133 121 1602 is key 3, MOQ 1. Remark 4 says the OLD bare spacer was NOT AVAILABLE SEPARATELY. Do not assign the old assembly number to the new bare spacer.
- Both old/new columns retain IS-M5x56 screws 9007 319 1121 (key 4, 2x), M5 hexagon nuts 9210 261 0700 (key 5, 2x) and plugs 4133 122 6900 (key 6, 2x). These unchanged numbers do not mean they may be omitted. Their MOQ cells are blank, not zero or copied from the spacer row. Two of each is an explicit installation quantity.
- The old complete-assembly inclusion range 3–6 is not a promise that the new separately listed flange includes the screws, nuts and plugs. The service connection requirements still apply. Footer date January 13, 1995 and retained 1994 bulletin identity remain distinct.
- Retained source conflict: this TI calls 9007 319 1121 an IS-M5x56 SPLINE screw, whereas the linked SCS01-2012 FS 72/74/76-D IPL calls the SAME number a HEXAGON-HEAD screw M5x56. Preserve both source descriptions; unchanged number is not proof of head/drive equivalence. The source-specific screw lengths, plugs and washer requirements remain binding.
- Historical TI 44/1994 guidance, not current stock, universal compatibility or physical verification. No hardware operation was performed.
Source: TI 44/1994, p. 3 — spacer supply changes and unchanged through-fasteners.
Part numbers (5)
- 4133 120 2202 — Original spacer-flange assembly; includes 3–6while factory stocks last · FS 74 / FS 76 only in the version/configuration described here
- 4133 121 1602 — New bare spacer flange; key 3MOQ 1; old bare spacer not separate · FS 74 / FS 76 only in the version/configuration described here
- 9007 319 1121 — IS-M5x56 screws; key 4, 2xsame number; MOQ unspecified · FS 74 / FS 76 only in the version/configuration described here
- 9210 261 0700 — M5 hexagon nuts; key 5, 2xsame number; MOQ unspecified · FS 74 / FS 76 only in the version/configuration described here
- 4133 122 6900 — Plugs; key 6, 2xsame number; MOQ unspecified · FS 74 / FS 76 only in the version/configuration described here
Conditional replacement · FS 72
FS 72: wider intake gasket can fit the old version
New gasket 4133 129 0902 has a 19 mm window versus 16 mm; this one-way fit statement does not promise a complete power upgrade.
- Gas-mixture window is19 mm wide in new gasket 4133 129 0902 versus 16 mm in original 4133 129 0900. The NEW gasket may be installed in OLD-version machines. Illustration 356TI002 shows original LEFT/new RIGHT and the changed outline/opening; no additional dimensions are inferred.
- Original gasket supplied only until existing stock lasts (remark 3); new MOQ 1. The one-way fit statement does NOT authorize old parts on a new-version machine, and changing the gasket alone does NOT deliver the full power increase: all new Plus parts remain required.
- This is the intake gasket, not cylinder-base gasket 4133 029 2300 shown on the later cylinder IPL. Exact fuel-sheet navigation retains gasket 0902; no gasket-thickness or cylinder-sealing change is inferred.
- Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.
Source: TI 12/1995, p. 1 · TI 12/1995, p. 2 · TI 12/1995, p. 3 — All three pages: power/cylinder, gasket/spacer/service conditions, Plus Series note and complete summary.
Part numbers (2)
- 4133 129 0900 — Original intake gasket;16 mm windowuntil stocks exhausted · FS 72; stated TI conditions
- 4133 129 0902 — New intake gasket;19 mm windowMOQ 1; permitted on old version · FS 72; stated TI conditions
Conditional replacement · FS 72
FS 72: spacer flange retrofit needs the complete fastening arrangement
New 19 mm flange requires M5x56 screws and plugs, plus M5x25 flange screws with A5.3 washers; check the entire intake connection.
- New spacer flange 4133 121 1602 has a 19 mm opening on the CYLINDER side. When installing it on an original-version machine, CHECK the screw connection filter base / carburetor / flange / cylinder. New-type replacement parts are mandatory for new-version machines, and ALL new Plus components are needed for the complete old-to-new power conversion.
- Illustration 356TI003 keys are LOCAL to that drawing:1=M5x56 screws, 2=plugs 4133 122 6900, 3=M5x25 screws securing flange to cylinder, 4=A5.3 washers. M5x56 screws AND plugs MUST be used with the new flange; flange MUST be secured with M5x25 screws AND A5.3 washers. No tightening torque for these connections is supplied; do not copy the cylinder 10 Nm value.
- Original spacer-flange ASSEMBLY 4133 120 2202, including summary keys 3–6, is supplied only while stocks last (remark 3). The new column for that assembly is a dash; the new standalone spacer flange 4133 121 1602 has MOQ 1. Remark 4 on the flange row says the OLD flange was not separately available; it does NOT prohibit separate supply of the NEW flange.
- Summary keys 3–6 are not illustration 356TI003 keys:3=flange, 4=TWO M5x56 screws 9007 319 1121, 5=TWO M5 hex nuts 9210 261 0700, 6=TWO plugs 4133 122 6900. Those three numbered fastener/plug items are unchanged. Original standalone flange is marked -*- with no number. All other cylinder parts as before.
- The TI calls 9007 319 1121 a spline screw; the later FS72/74/76 IPL calls the SAME number a hexagon head screw M5x56. Preserve this head-description conflict. The TI gives dimensions but no order numbers for the M5x25 flange screws or A5.3 washers; later catalog numbers are NOT silently promoted into the 1995 roster.
- Last TI 01.94 is bibliographic. Footer: Waiblingen, January 17, 1995; ©1995 Andreas Stihl; D1/MTK-na, Technical Documentation. Issue 12.95 is not a December introduction date. Historical availability is not present-day stock.
- Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.
Source: TI 12/1995, p. 1 · TI 12/1995, p. 2 · TI 12/1995, p. 3 — All three pages: power/cylinder, gasket/spacer/service conditions, Plus Series note and complete summary.
Part numbers (5)
- 4133 120 2202 — Original spacer flange assemblykeys 3–6; until stocks exhausted · FS 72; stated TI conditions
- 4133 121 1602 — New standalone spacer flange; summary key 3MOQ 1;19 mm cylinder-side opening · FS 72; stated TI conditions
- 9007 319 1121 — M5x56 screw; summary key 4; twounchanged; TI spline / later IPL hex head conflict · FS 72; stated TI conditions
- 9210 261 0700 — Hexagon nut M5; summary key 5; twounchanged · FS 72; stated TI conditions
- 4133 122 6900 — Plug; summary key 6; twounchanged; mandatory with new flange · FS 72; stated TI conditions
Wrong number or missing part for the FS 72, FS 74, FS 76? Report a correction →