← Edgers & other equipment · series 4133

Stihl 4133 · Section M · 11 of 16 · 27 parts

FS 74: Gear head, Drive tube assembly

Fits FS 74.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213151617181922202122222324253456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (27)

PosPart numberDescriptionQty
1 4130 641 0305 Gear housing Fitment / change note → 1
2 9503 003 9850 Grooved ball bearing 609 Fitment / change note → → replaced by 9503 003 9853 TI 46/2000 2
3 not sold separately Drive pinion not available as a separate item 1
4 not sold separately Spur bevel gear not available as a separate item 1
5 4130 642 0601 Drive shaft Fitment / change note → 1
6 9503 003 5190 Grooved ball bearing 6001-2RS 1
7 9456 621 3100 Circlip 28x1.2 1
8 9503 003 9853 Grooved ball bearing 609-2Z Fitment / change note → 1
9 9455 621 0750 Circlip 9x1 Fitment / change note → 1
10 9456 621 2660 Circlip 24x1.2 Fitment / change note → 1
11 4119 713 6500 Screw plug 1
12 4137 710 3800 Thrust plate 1
13 not sold separately Guard washer not available as a separate item 1
15 4130 713 1600 Thrust washer Fitment / change note → 1
16 4126 642 7600 Collar nut M10x1 l/h thread 1
17 9075 478 4159 Pan head self-tapping screw IS-D5x24 Fitment / change note → 2
18 4126 713 3100 Rider plate 1
19 4133 711 0213 Drive tube 1
20 4133 711 7310 Flexible liner 1
21 4137 711 3202 Drive shaft 1
22 4119 182 2110 Support 2
23 4140 007 1006 Hose clamp kit 1
24 9022 341 1270 Spline screw IS-M6x14 1
25 4133 717 2000 Cap 1
Not numbered on the diagram — assemblies, kits and options
— 4137 640 0100 Gearhead Fitment / change note → 1
— 4130 640 7301 Set of pinions Fitment / change note → 1
— 0781 120 1117 Gear lubricant 80 g not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 74

FS 74: flexible drive shaft replacement

4130 711 3205 → 4133 711 3215; no FS 72/76 applicability is added.

  • To standardize parts, flexible drive shaft 4133 711 3215 will be supplied instead of original 4130 711 3205. Section7 explicitly names FS 74 only.
  • Introduction is in progress; original shafts are supplied only until existing factory stocks are exhausted. No shaft dimension, production serial or required companion replacement is specified.
  • Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.

Source: TI 1/1994, p. 8 — FS 74: flexible drive shaft replacement.

Part numbers (2)
  • 4130 711 3205 — Original FS74 flexible drive shaftoriginal · FS 74: flexible drive shaft replacement
  • 4133 711 3215 — Replacement FS74 flexible drive shaftreplacement · FS 74: flexible drive shaft replacement

Service note · FS 44 / FS 74 / FS 80 / FS 85

FS 44 / 74 / 80 / 85: splined gearhead and matched thrust parts

FS 80/85 change at X 35 221 994; replacement supply includes the matching plate and washer.

X 35 221 994 — FS80 and FS85 production change only; FS74 in progress; FS44 replacement scope, not this serial cutoff.

  • New gearhead replaces the original on FS 80 and FS 85 from X 35 221 994 to improve transmission of power. It is also a replacement for FS 44 and FS 74. The serial cutoff belongs ONLY to FS 80/85; FS 74 introduction is in progress. No extension to shared-sheet FS 36/40, FS 72/76, FS 75 or R/T/RX variants.
  • Page1 comparison: old4130 640 0100 is 1:1.33 / 7900 rpm, two flats; new4137 640 0100 is 1:1.40 / 7500 rpm, splined. These are rated maximum OUTPUT-SHAFT speeds, NOT engine tuning settings. Drawing342TI009 GM contrasts the old two-flat connection on the left with splined shaft, plate and washer on the right.
  • TI19/1996 page3, specifically for FS 44, instead prints7500 rpm for old4130 640 0100 and7000 rpm for new4130 640 0101. Preserve that source/model/assembly context and the differing figures; TI32 does not explicitly revoke the earlier FS 44 speed or authorize raising it. Do not collapse the two tables into one universal limit.
  • New gearheads supplied ONLY TOGETHER WITH new thrust plate14 and thrust washer16. Plate14 includes protective washer15. Original plate4126 710 3800 and washer4126 713 1600 remain spares (remark2); old protective washer has no number and is not a spare (remark4). New protective washer4112 717 2801 is separately numbered. No mixed two-flat/splined assembly authorized.
  • Old gearhead table includes1,2,4,6,8–16; new includes1,3,5,7–16. Old complete4130 640 0100 supplied only until factory stocks exhausted (remark1). All other parts as before; the table is not a complete independent IPL. Later FS74 and FS80/85 sheets retain4137 gearhead but list thrust plate4137 710 3800 rather than source4130 710 3801; no silent replacement of historical numbers or proof of supersession.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Sections1.1,1.3,1.4 and1.6 gearhead/thrust rows, drawing and supply.

Referenced bulletin evidence: TI 19/1996, p. 3 · TI 19/1996, p. 5 — Earlier FS44-specific speed comparison and assembly table.

Part numbers (7)
  • 4130 640 0100 — Original gearhead, two-flat outputStock exhaustion · Only the exact model/configuration and restrictions of 1997-32
  • 4137 640 0100 — New gearhead, splined outputSupplied with new thrust plate and washer · Only the exact model/configuration and restrictions of 1997-32
  • 4126 710 3800 — Original thrust plate including protective washerRemains spare · Only the exact model/configuration and restrictions of 1997-32
  • 4130 710 3801 — New thrust plate including item15Item14 · Only the exact model/configuration and restrictions of 1997-32
  • 4112 717 2801 — New protective washerItem15; original not a spare · Only the exact model/configuration and restrictions of 1997-32
  • 4126 713 1600 — Original thrust washerRemains spare · Only the exact model/configuration and restrictions of 1997-32
  • 4130 713 1600 — New thrust washerItem16 · Only the exact model/configuration and restrictions of 1997-32

Service note · FS 44 / FS 74 / FS 80 / FS 85

FS 44 / 74 / 80 / 85: gear housing, retaining rings and DG screw torque

Only new gearhead 4137 640 0100 DG screws take 8.5 Nm (6.3 lbf.ft).

  • Section1.5 specifies8.5 Nm (6.3 lbf.ft) ONLY for the DG screws, item3, in NEW gearhead4137 640 0100. This is not a torque for original IS-M5x20 screws or every fastener on these models. No torque inferred for a4130 640 0101 assembly.
  • Items1–7: housing0300→0305; two9022 371 1020 IS-M5x20 screws replaced by two9075 478 4159 DG5x24 screws; ring22x1→24x1.2 and ring9.5x0.8→9.0x1.0. All original housing/screw/ring rows carry remark2, original remains spare. Continued spare supply does not authorize arbitrary mixing.
  • Drawing393TI004 GM explicitly pairs screws2/3 and rings4/5,6/7. TI callouts are not current IPL positions. Lower shaft bearing, screw plug and collar nut are drawn without numbers in this abbreviated summary; no new number or deletion inferred. Model production/replacement scope follows section1.1, not the other models sharing an IPL sheet.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Sections1.5 and1.6: torque, all housing/screw/ring rows and drawing.

Part numbers (8)
  • 4130 641 0300 — Original gear housingRemains spare · Only the exact model/configuration and restrictions of 1997-32
  • 4130 641 0305 — New gear housingItem1 · Only the exact model/configuration and restrictions of 1997-32
  • 9022 371 1020 — Original IS-M5x20 spline screw, twoItem2; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 9075 478 4159 — New DG5x24 spline screw, twoItem3; 8.5 Nm · Only the exact model/configuration and restrictions of 1997-32
  • 9456 621 2440 — Original retainer ring22x1Item4; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 9456 621 2660 — New retainer ring24x1.2Item5 · Only the exact model/configuration and restrictions of 1997-32
  • 9452 600 0750 — Original retainer ring9.5x0.8Item6; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 9455 621 0750 — New retainer ring9.0x1.0Item7 · Only the exact model/configuration and restrictions of 1997-32

Service note · FS 44 / FS 74 / FS 80 / FS 85

FS 44 / 74 / 80 / 85: coordinated bearings, pinion set and shaft

Two bearing positions change; pinions remain a set, not separate spare items.

  • Bearing2Z item8:9507 003 8056→9503 003 9853. TWO item9 bearings:9507 003 8054→9503 003 9850. Do not merge these bearing positions or assume all use9853. Old bearing rows remain spares under remark2.
  • Item10 pinion set4130 640 7300→4130 640 7301 consists of drive pinion11 and spur bevel gear12. Both individual rows have -*- and remark3: NOT AVAILABLE AS SEPARATE ITEMS. Drawing places10/11 on the input side and10/12 on the output side; these are two members of one set, not two different set numbers.
  • Item13 output shaft4130 642 0610→4130 642 0601 accompanies the two-flat-to-splined change. Old shaft and old pinion set remain spares (remark2). These coordinated changes are not approval to mix individual pinions, ratios, shafts or bearings across designs. The serial/model restrictions are those of section1.1.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 32/1997, p. 1 · TI 32/1997, p. 2 · TI 32/1997, p. 3 — Section1.6 items8–13, drawing, quantities and supply.

Part numbers (8)
  • 9507 003 8056 — Original grooved ball bearing2ZItem8; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 9503 003 9853 — New grooved ball bearing2ZItem8 · Only the exact model/configuration and restrictions of 1997-32
  • 9507 003 8054 — Original grooved ball bearing, twoItem9; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 9503 003 9850 — New grooved ball bearing, twoItem9 · Only the exact model/configuration and restrictions of 1997-32
  • 4130 640 7300 — Original set of pinionsItem10; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 4130 640 7301 — New set of pinionsItem10; includes11/12 · Only the exact model/configuration and restrictions of 1997-32
  • 4130 642 0610 — Original output shaftItem13; remains spare · Only the exact model/configuration and restrictions of 1997-32
  • 4130 642 0601 — New output shaftItem13; splined · Only the exact model/configuration and restrictions of 1997-32

Wrong number or missing part for the FS 74? Report a correction →