Stihl 4133 · Section O · 13 of 16 · 26 parts
FS 76: Gear head, Drive tube assembly
Fits FS 76.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (26)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 641 0300 | Gear housing | 1 |
| 3 | 9503 003 9850 | Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 | 2 |
| 4 | not sold separately | Drive pinion not available as a separate item | 1 |
| 5 | not sold separately | Spur bevel gear not available as a separate item | 1 |
| 6 | 9503 003 9853 | Grooved ball bearing 609-2Z | 1 |
| 7 | 9455 621 0750 | Circlip 9x1 | 1 |
| 8 | 9456 621 2660 | Circlip 24x1.2 | 1 |
| 9 | 4124 642 0600 | Drive shaft | 1 |
| 10 | 9503 003 5190 | Grooved ball bearing 6001-2RS Fitment / change note → | 1 |
| 11 | 9456 621 3100 | Circlip 28x1.2 | 1 |
| 12 | 4119 713 6500 | Screw plug Fitment / change note → | 1 |
| 13 | 0000 958 0503 | Washer | 2 |
| 14 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 15 | 4126 710 3800 | Thrust plate | 1 |
| 16 | 4126 713 1600 | Thrust washer | 1 |
| 17 | 4126 713 3100 | Rider plate | 1 |
| 18 | 4126 642 7600 | Collar nut M10x1 l/h thread | 1 |
| 19 | 4124 710 7103 | Drive tube assembly Ø 24 mm / 15/16'' | 1 |
| 20 | 4124 711 3200 | Drive shaft | 1 |
| 21 | 4123 182 2100 | Clamp | 2 |
| 22 | 4114 710 6701 | Hose clamp | 1 |
| 23 | 9022 341 1270 | Spline screw IS-M6x14 | 1 |
| 24 | 4133 717 2000 | Cap | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4133 640 0100 | Gearhead | 1 |
| — | 4124 640 7300 | Set of pinions | 1 |
| — | 0781 120 1117 | Gear lubricant 80 g not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 74 / FS 76
FS 74, FS 76: gearhead screw plug gains a hexagon head
4117 713 6501 → 4119 713 6500 from X 24 993 106; old plug remains for other models.
- The new plug 4119 713 6500 (item2) adds a 13 mm (approximately 1/2 in) external hexagon to the Torx spline socket, simplifying release of a tight plug. Original plug 4117 713 6501 is item1. The change starts from machine No. X 24 993 106 for the section8 FS 74/76 scope.
- The original plug remains available for OTHER models. The shared summary label Gearhead FS 76, 81 does not establish an FS 81 production cutoff or extend the section8.3 mowing-head installation rule. No plug torque or lubricant specification is supplied.
- Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 9 · TI 1/1994, p. 10 — FS 74, FS 76: gearhead screw plug gains a hexagon head.
Part numbers (2)
- 4117 713 6501 — Original Torx screw plug; retained for other modelsoriginal · FS 74, FS 76: gearhead screw plug gains a hexagon head
- 4119 713 6500 — New Torx plus 13mm hexagon screw plugreplacement · FS 74, FS 76: gearhead screw plug gains a hexagon head
Service note · FS 74 / FS 76
FS 74, FS 76: two-seal output bearing is a spare-part change
9503 003 5140 → 9503 003 5190 for service; original bearing continues in production.
- At the output end of the gear shaft, the original bearing 9503 003 5140 (item3) has ONE sealing washer and continues to be installed on the production line. Replacement bearing 9503 003 5190 has seals on BOTH sides and can therefore be installed either way round.
- The new bearing is to be supplied as a spare; introduction is in progress and original spare stock is supplied only until exhausted. Do not apply the screw-plug serial X 24 993 106 to the bearing or claim production has switched to the two-seal bearing.
- The exploded drawing identifies the output-end bearing item3; no dimensions, clearance class, press direction or complete-gearhead interchange is established.
- Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 9 · TI 1/1994, p. 10 — FS 74, FS 76: two-seal output bearing is a spare-part change.
Part numbers (2)
- 9503 003 5140 — Original output-end bearing, one sealing washerproduction-retained · FS 74, FS 76: two-seal output bearing is a spare-part change
- 9503 003 5190 — Replacement output-end bearing, two sealing washersreplacement-spare · FS 74, FS 76: two-seal output bearing is a spare-part change
Service note · FS 74 / FS 76 / FS 81
FS 74, FS 76, FS 81: gearhead assembly numbers stay unchanged
4130 640 0100 and 4124 640 0101 retain their numbers, with different factory-stock rules.
- The page10 summary labels 4130 640 0100 Gearhead FS 74 and 4124 640 0101 Gearhead FS 76, 81. Both retain their numbers and include the plug and output bearing rows; other parts remain as before. The two complete gearheads are not asserted interchangeable.
- Unmodified FS 74 gearhead 4130 640 0100 is supplied until existing factory stocks are exhausted; only the modified FS 76/81 gearhead 4124 640 0101 is factory-available. The common number alone does not establish which revision a used assembly contains.
- The narrative heading names FS 74/76, while the summary also names FS 81. Preserve FS 81 only as the explicit assembly-row application; do not extrapolate the plug production serial, bearing production rule or AutoCut mounting instruction to FS 81 solely from this row.
- Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 9 · TI 1/1994, p. 10 — FS 74, FS 76, FS 81: gearhead assembly numbers stay unchanged.
Part numbers (2)
- 4130 640 0100 — FS74 complete gearhead; unchanged numberunchanged-number · FS 74, FS 76, FS 81: gearhead assembly numbers stay unchanged
- 4124 640 0101 — FS76/81 complete gearhead; unchanged numberunchanged-number · FS 74, FS 76, FS 81: gearhead assembly numbers stay unchanged
Service note · FS 74 / FS 76
FS 74, FS 76: AutoCut 24-2 requires the intermediate washer
Fit 4112 713 8500 between the thrust washer and guard washer.
- When mounting the STIHL AutoCut 24-2 mowing head on these gearheads, washer 4112 713 8500 (item5) MUST be fitted between thrust washer item4 and guard washer item6. The original exploded view and the highlighted instruction agree.
- No part numbers for items4 or6 are stated here; do not substitute their callout numbers as parts or infer the same stack for other heads. No mounting torque or independent head/guard compatibility approval is given.
- Historical English TI01/1994, sections 5–10. Exact named models and the specified assembly are retained; no unlisted variants or current spare availability are inferred. No physical interchange test was performed.
Source: TI 1/1994, p. 9 — FS 74, FS 76: AutoCut 24-2 requires the intermediate washer.
Part numbers (1)
- 4112 713 8500 — Required intermediate washer for AutoCut24-2 mountingrequired-component · FS 74, FS 76: AutoCut 24-2 requires the intermediate washer
Wrong number or missing part for the FS 76? Report a correction →