Stihl 4134 · Section C · 3 of 12 · 28 parts
Fuel tank, Clutch
Fits BT 120 C.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4134 350 0400 | Fuel tank | 1 |
| 2 | 4128 358 0800 | Hose | 1 |
| 3 | 0000 350 3506 | Pickup body | 1 |
| 4 | not sold separately | Hose 2.2x5.4x205 mm, R1 not available as a separate item | 1 |
| 5 | 0000 989 0516 | Grommet | 1 |
| 6 | 0000 351 3200 | Sleeve | 4 |
| 7 | 1125 084 8900 | Grommet | 4 |
| 8 | 0000 951 1102 | Screw IS-D5x26 | 4 |
| 9 | 4128 350 0505 | Filler cap | 1 |
| 10 | 0000 350 0900 | Rope | 1 |
| 11 | 0000 353 0800 | Filler cap retainer | 1 |
| 12 | 0000 711 8700 | Collar screw | 4 |
| 13 | 4128 160 2001 | Clutch Fitment / change note → | 1 |
| 14 | not sold separately | Clutch shoe not available as a separate item | 2 |
| 15 | 0000 997 5519 | Tension spring | 2 |
| 16 | 0000 961 0608 | Ring | 2 |
| 17 | 4128 162 1000 | Cover washer | 1 |
| 18 | 0000 951 0606 | Hexagon head screw | 2 |
| 19 | 0000 958 1000 | Washer 16x10x0.5 Fitment / change note → | 2 |
| 20 | 4134 182 2104 | Support, bottom | 1 |
| 21 | 4134 180 6702 | Support | 1 |
| 22 | 9291 021 0120 | Washer 5.3 | 1 |
| 23 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 1 |
| 24 | 4134 182 2105 NLA | Support, bottom | 1 |
| 25 | 4134 180 6701 NLA | Support → replaced by 4134 180 6702 TI 5/2003 | 1 |
| 26 | 0000 951 1100 | Screw IS-D5x20 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2802 | Hose 2.2x5.4 mm x 1 m, R1 not illustratedoption | 1 |
| — | 4134 180 6700 NLA | Support | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · BT 120 C / FS 120 / FS 200 / FS 250 / FS 350
TI09: clutch washers require the new matched assembly
Do not fit the new washers to the old clutch or mix old/new carriers and shoes.
- Clutch 4128 160 2000 was replaced by 4128 160 2001 for quieter operation. The new clutch has two washers 0000 958 1000, 16 x 10 x 0.5 mm, one at each bearing point between carrier and clutch shoe.
- The washers must NOT be installed in the previous clutch. Old and new carriers and shoes must not be combined for dimensional reasons. The table phrase all other parts as before does not override this prohibition.
- The source recommends replacing the previous clutch with the complete new assembly rather than replacing its individual parts. Only new clutch 4128 160 2001 is available from the factory; the old assembly is no longer supplied. This is historical factory availability, not current stock verification.
- The summary gives USA production from serial 2 52 747 650. It does not assign a separate serial to each heading model, establish a worldwide cutoff or define a model production range. Keep this as a USA clutch-change statement, not a crankshaft or seal cutoff.
- Only the printed TI09/2003 models and described configurations are covered. Shared catalog sheets do not extend this assertion to FS 300, BT 121, SP 200, HT 250 or unlisted R variants. No physical interchange test was performed.
Source: TI 9/2003, p. 1 · TI 9/2003, p. 21 — 5 clutch, illustration and complete summary.
Part numbers (3)
- 4128 160 2000 — Previous clutch assemblyReplaced; no longer factory supplied · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
- 4128 160 2001 — New clutch assemblyUse matched carrier and shoes · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
- 0000 958 1000 — Washer16x10x0.5Two; new clutch only · TI09/2003 section 5 clutch, illustration and complete summary models/configurations only; preserve restrictions above
Service note · BT 120 C
BT 120 C: engine, fuel and ignition specifications
30.8cm³, 1.3kW and a single-LD carburetor are historical 1998 specifications.
- Section2.1: displacement30.8cm³ (1.88cu.in), bore35mm (1.37in), stroke32mm (1.26in); power1.3kW (1.8bhp) to ISO8893. Single-pawl rewind starter with ElastoStart grip. Rope refers to section4; no rope dimension is supplied here.
- All-position diaphragm carburetor with integral fuel pump and ONE adjusting screw. Idle2800rpm; clutch engagement4300rpm. Fuel capacity0.64l (1.35USpt). Do not substitute later H/L/LA adjustments or interpret the engagement value as an idle target.
- Ignition module has integral electronic speed limiter. Suppressed spark plugs listed: Bosch WSR6F, NGK BPMR7A or Champion RCJ6Y. No plug gap, torque, ignition timing or mixture ratio is specified on this page; none is inferred.
- Historical BT 120 C only. TI37/1998 calls the machine series4313; the catalog groups its exact-model sheets under4134. Those identifiers are retained, not declared equivalent. Later carburetor/control revisions and BT121 are not included. No hardware operation was performed.
Source: TI 37/1998, p. 3 — Complete2.1.1–2.1.3.
No additional parts-table entry added.
Wrong number or missing part for the BT 120 C? Report a correction →