Stihl 4134 · Section P · 15 of 18 · 32 parts
Gear head, Drive tube assembly
Fits FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4130 641 0305 | Gear housing | 1 |
| 2 | 9503 003 9850 | Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 | 2 |
| 3 | not sold separately | Drive pinion not available as a separate item | 1 |
| 4 | not sold separately | Spur bevel gear not available as a separate item | 1 |
| 5 | 4130 642 0601 | Drive shaft | 1 |
| 6 | 9503 003 5190 | Grooved ball bearing 6001-2RS | 1 |
| 7 | 9456 621 3100 | Circlip 28x1.2 | 1 |
| 8 | 9503 003 9853 | Grooved ball bearing 609-2Z | 1 |
| 9 | 9455 621 0750 | Circlip 9x1 | 1 |
| 10 | 9456 621 2660 | Circlip 24x1.2 | 1 |
| 11 | 4119 713 6500 | Screw plug | 1 |
| 12 | 4137 710 3800 | Thrust plate | 1 |
| 13 | not sold separately | Guard washer not available as a separate item | 1 |
| 15 | 4130 713 1600 | Thrust washer | 1 |
| 16 | 4126 642 7600 | Collar nut M10x1 l/h thread | 1 |
| 17 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| 18 | 4126 713 3100 | Rider plate option | 1 |
| 20 | 4137 710 7134 | Drive tube assembly Ø 25.4 mm / 1'' Fitment / change note → | 1 |
| 21 | 4134 711 7303 | Flexible liner 1375 mm / 54 3/16'' Fitment / change note → | 1 |
| 22 | 4137 711 7300 | Flexible liner 1455 mm / 57 5/16'' Fitment / change note → | 1 |
| 23 | 4137 711 2101 | Plug Fitment / change note → | 1 |
| 24 | 4137 711 2101 | Plug Fitment / change note → | 1 |
| 25 | 4137 711 3200 | Drive shaft → replaced by 4137 711 3202 TI 11/2005 | 1 |
| 26 | 4119 182 2110 | Support | 2 |
| 27 | 4140 007 1006 | Hose clamp kit | 1 |
| 28 | 9022 341 1270 | Spline screw IS-M6x14 | 1 |
| 29 | 0000 711 2500 | Sleeve | 1 |
| 30 | 0000 967 3725 | Warning pictogram FS | 1 |
| 31 | 0000 967 3684 | Warning pictogram FS Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4137 640 0100 | Gearhead | 1 |
| — | 4130 640 7301 | Set of pinions | 1 |
| — | 0781 120 1117 | Gear lubricant 80 g not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FS 120 / FS 200
FS 120 / FS 200: reinforced drive tube and shorter liner
A 90 mm steel sleeve replaces the lower plug; liner and tube dimensions stay model-specific.
- A 90 mm (3 1/2 inch) steel sleeve is installed at the lower end of the 25.4 mm / 1 inch drive tube to strengthen the gearhead-clamp area. The lower plug is deleted; plug 4137 711 2101 stays under the same number but quantity falls from two to one. Illustration labels tube 1, steel sleeve 2 and liner 3; no separate sleeve order number is supplied.
- Tube 4137 710 7100 becomes 4137 710 7134; flexible liner changes from 4137 711 7300, 1455 mm (57 9/32 inch), to 4134 711 7303, 1375 mm (54 1/8 inch). Instruction label 0000 967 3684 is unchanged. The summary includes liner, plug and label with the tube.
- FS 120/200 introduction is in progress without a numeric cutoff. Both previous tube and previous liner remain available as spares; do not apply the FS 350 stock-exhaustion rule to them.
- TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 22/2001, p. 1 · TI 22/2001, p. 2 — 1 update context;2 complete drawing, table and remarks.
Part numbers (6)
- 4137 710 7100 — Previous drive tubePrevious · FS 120, FS 200; stated configuration only
- 4137 710 7134 — Steel-sleeved drive tubeNew · FS 120, FS 200; stated configuration only
- 4137 711 7300 — Previous longer flexible linerRemains spare · FS 120, FS 200; stated configuration only
- 4134 711 7303 — Shorter flexible linerNew · FS 120, FS 200; stated configuration only
- 4137 711 2101 — Drive-tube plugUnchanged number; one instead of two · FS 120, FS 200; stated configuration only
- 0000 967 3684 — Instruction labelUnchanged · FS 120, FS 200; stated configuration only
Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450
FS120/200/350/400/450: clutch and rigid-shaft construction
Two unlined clutch shoes;4,300 rpm engagement is not idle or cut-off speed.
- Clutch uses TWO LARGE-DIAMETER SHOES WITHOUT LININGS. The rigid drive shaft is supported in a FULL-LENGTH LINER. Neither description supplies part numbers, wear limits, lubrication intervals or a shaft conversion.
- Every engine-table column gives clutch engagement at4,300 rpm. Do not confuse that value with2,800 rpm idle, electronic cut-off without a cutting tool, or the rated output-shaft speed. No field clutch test was performed.
- Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.
Source: TI 42/1997, p. 3 — Section1 clutch/shaft; section2.1.1 clutch row.
No additional parts-table entry added.
Wrong number or missing part for the FS 120, FS 120 R, FS 200, FS 200 R, FS 250, FS 250 R? Report a correction →