← Augers/Drills & other equipment · series 4134

Stihl 4134 · Section D · 4 of 14 · 32 parts

Carburetor housing, Air filter

Fits FS 300, FS 350.

Parts diagrams →

Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922122232425262728293303145666666789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 4134 120 0102 Carburetor housing Fitment / change note → 1
2 4134 120 0101 NLA Carburetor housing Fitment / change note → 1
3 4134 120 0100 NLA Carburetor housing Fitment / change note → 1
4 4134 122 6601 Collar screw Fitment / change note → 2
5 0000 963 1403 Bushing Fitment / change note → 1
6 0000 951 1100 Screw IS-D5x20 Fitment / change note → 4
7 4128 129 0900 Gasket Fitment / change note → 1
8 4134 120 0652 Carburetor C1Q-S161 1
9 4134 120 0653 Carburetor C1Q-S162 1
10 4134 120 0654 Carburetor C1Q-S163 1
11 4134 120 0655 Carburetor C1Q-S164 1
12 4134 120 0651 NLA Carburetor C1Q-S51C Fitment / change note → 1
13 4134 123 7502 Grommet Fitment / change note → 1
14 4134 431 7000 Contact plate Fitment / change note → 1
15 4128 129 0900 Gasket Fitment / change note → 1
16 not sold separately Carburetor C1Q-S35B no longer available from factory 1
17 4134 123 7501 Grommet 1
18 4134 123 7500 Grommet 1
19 4134 122 1801 Heat shield 1
21 4134 129 0900 Gasket 1
22 4134 140 2801 Filter housing 1
23 4134 140 2850 Filter housing 1
24 9216 261 0700 Hexagon nut M5 2
25 4134 141 0300 Air filter 1
26 4128 141 0310 Air filter 1
27 4134 141 0500 Filter cover 1
28 4128 182 9500 Choke knob 1
29 0000 350 6201 Fuel pump 1
30 4130 350 6200 Fuel pump → replaced by 4128 120 0100 TI 6/2009 1
31 not sold separately Hose 2.2x5.4x67 mm, R1 not available as a separate item 1
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2802 Hose 2.2x5.4 mm x 1 m, R1 not illustratedoption 1
— 4134 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FS 120 / FS 200 / FS 250 / FS 300 / FS 350 / FR 350 / BT 120 C

TI42: cable-based STOP circuit requires contact plate and longer studs

If the contact plate is missing, retrofit it with the gasket and longer collar studs.

  • Applies to named machines with throttle cable but WITHOUT a short-circuit wire and ground wire: STOP switching uses the cable sheath and the cable itself. It does not prescribe this arrangement for the later two-wire cable system.
  • If missing, retrofit contact plate 4134 431 7000 and gasket 4128 129 0900 to provide consistent electrical continuity for STOP. Diagram identifies cable 1, carburetor 2, plate 3, gasket 4, nuts 5 and collar stud 6. Tightening hex nuts presses the plate claw into the collar stud, grounding through the carburetor to the engine and ignition system. No torque or electrical resistance limit is specified.
  • Existing collar studs must be replaced with longer 4134 122 6601 when plate and additional gasket are retrofitted. Drawing compares 40 mm (1 18/32 inch) and 42 mm (1 21/32 inch) spans from shoulder to threaded end, not overall lengths including the plastoform thread. TI21/2000 separately documents the interim longer old-number screw for FS 120/200; TI42 itself does not repeat that exception or name the old stud number.
  • FR 350 is explicitly named in the original heading, but no exact FR 350 sheet is bound here. The three linked sheets are navigation for the other named models only; they are not FR 350 physical-interchange proof. TI22/2001 in the footer is the last-TI bibliography. TI09/2003 explicitly requires this bulletin before control conversion, but its remaining control/cable instructions and TI22 dependency still need review; this note alone is not a full conversion procedure.
  • Only the named source models and stated configuration are covered; shared catalog sheets do not extend this note to unnamed models or R variants. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 42/2002, p. 1 — Entire TI42/2002, both diagrams and mandatory retrofit note.

Part numbers (3)
  • 4134 431 7000 — Contact plateMandatory if missing in cable-based STOP configuration · FS 120, FS 200, FS 250, FS 300, FS 350, FR 350, BT 120 C; stated source configuration only
  • 4128 129 0900 — Additional carburetor gasketRequired with contact plate · FS 120, FS 200, FS 250, FS 300, FS 350, FR 350, BT 120 C; stated source configuration only
  • 4134 122 6601 — Longer collar studRequired when retrofitting plate and gasket · FS 120, FS 200, FS 250, FS 300, FS 350, FR 350, BT 120 C; stated source configuration only

Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C

TI22: match carburetor housing to cylinder mounting bosses

Old two-boss cylinders must retain housing 0100; the new assembly adds a third screw and bushing.

  • Housing 4134 120 0100 becomes 4134 120 0101 for improved sealing, with an additional cylinder mounting boss. New bushing 0000 963 1403 strengthens the assembly at operating temperature. Screw IS-DG 5x20 0000 951 1100 keeps its number but quantity increases by one for three-point mounting.
  • The previous housing 4134 120 0100 MUST be used on previous cylinders with two mounting bosses and remains available for older machines. Do not infer that new housing alone retrofits to the two-boss cylinder.
  • Cylinder-with-piston pairs are FS 120/BT 120 C: 4134 020 1208 to 4134 020 1213; FS 200: 4134 020 1207 to 4134 020 1212; FS 350: 4134 020 1205 to 4134 020 1210. Previous cylinders are no longer factory supplied. FS 350 change starts at 1 50 967 373; FS 120/200 and BT 120 C are in progress, not that serial.
  • TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 22/2001, p. 1 · TI 22/2001, p. 3 — 3 entire housing/cylinder diagram, service note and summary.

Part numbers (10)
  • 4134 120 0100 — Two-boss carburetor housingRequired on old cylinders · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 120 0101 — Three-point carburetor housingNew cylinder configuration · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 951 1100 — IS-DG 5x20 screwUnchanged number; one additional · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 963 1403 — Reinforcing bushingNew · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 020 1208 — Cylinder with pistonPrevious; no longer factory supplied · FS 120 / BT 120 C
  • 4134 020 1213 — Cylinder with pistonNew three-boss version · FS 120 / BT 120 C
  • 4134 020 1207 — Cylinder with pistonPrevious; no longer factory supplied · FS 200
  • 4134 020 1212 — Cylinder with pistonNew three-boss version · FS 200
  • 4134 020 1205 — Cylinder with pistonPrevious; no longer factory supplied · FS 350
  • 4134 020 1210 — Cylinder with pistonNew three-boss version · FS 350

Conditional replacement · FS 120 / FS 200 / FS 350 / BT 120 C

TI22: new throttle retainer requires the longer screw on old machines

Old-machine repair also adds the ignition-wire holder and requires readjustment.

  • Upper retainer 4134 182 2101 with integral wire holder becomes 4134 180 6701 with metal cover. Cover is included and unavailable separately; no order number is invented. New ignition lead with protective hose makes the previous integral holder unnecessary.
  • For old-machine throttle-cable service, fit the new retainer with 4 mm longer IS-DG5x24Z screw 0000 951 1103 instead of IS-DG5x20Z 0000 951 1100. DO NOT secure the new retainer with the short screw. Also fit ignition-lead wire holder 4134 448 1200 BETWEEN FIRST AND SECOND cylinder fins. Readjust throttle cable and carburetor after this work; no settings are invented here.
  • FS 350 retainer introduction is from serial 1 50 399 211. FS 120/200 and BT 120 C introduction is in progress, not that cutoff. Previous retainer is supplied while stocks last; old screw remains a spare, not permission to fit it to the new retainer.
  • Last-TI list (FS 120/200 TI21/2000; FS 350 TI10/2000; BT 120 C TI37/1998) is bibliographic, not an unstated additional prerequisite. TI09/2003 control conversion still needs its own remaining source review; this note alone is not a complete conversion procedure.
  • TI22 describes an interdependent update package. Its introduction says most new parts were fitted to FS 250 from production start, with unspecified exceptions; this is not blanket FS 250 fitment approval. Shared sheets do not extend the named model/configuration scope. Factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 22/2001, p. 12 — 11 complete diagram, service note, summary, remarks and bibliographic footer.

Part numbers (5)
  • 4134 182 2101 — Previous upper retainerStocks only · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 180 6701 — New upper retainer with metal coverLonger screw required · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 951 1100 — IS-DG5x20Z short screwPrevious; forbidden with new retainer · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 0000 951 1103 — IS-DG5x24Z screwRequired longer screw · FS 120, FS 200, FS 350, BT 120 C; stated configuration only
  • 4134 448 1200 — Ignition-lead wire holderRequired on older machines; between first two fins · FS 120, FS 200, FS 350, BT 120 C; stated configuration only

Conditional replacement · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C

TI 09: retainer wiring uses blue plug and black ground terminal

Fit the washer under the screw head; the old sheath-contact STOP path is replaced.

  • Old retainer assembly 4134 180 6700 includes items 2–4. Retainer 4134 180 6701 becomes 4134 180 6702; lower retainer 4134 182 2105 becomes 4134 182 2104. IS-D5x24 screw 9075 478 4159 retains its number. New DIN125-A5.3 washer 9291 021 0120 fits UNDER the retainer screw head. No new complete-retainer assembly order number is printed.
  • Retainer-to-ignition short-circuit wire 4134 440 1100 becomes 4134 440 1101: old terminal contacted the cable sheath; new wire uses a plug connection. New retainer carries both the engine-ground connection and extension to the ignition module. Previous parts marked remark 1 remain spares for older machines, not mixed-system approval.
  • Push the ignition-module wire connector (1) into the lower-retainer recess. Seat the throttle cable in the carburetor housing as far as the STOP shown by the arrow; position it in the retainer. Slide BLUE short-circuit connector (2) onto terminal (3). Fit retainer cover, then secure BLACK ground-wire terminal (4) on TOP of the retainer with IS-D5x24 screw and washer. Do not swap blue plug connection and black screw-ground terminal.
  • This is the TI 09 new two-wire system, not the earlier TI 22 upper-retainer repair alone. No screw torque is specified here; do not import the loop-handle hose-clamp torque or an ignition-module washer number.
  • USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.

Source: TI 9/2003, p. 3 · TI 9/2003, p. 5 · TI 9/2003, p. 7 · TI 9/2003, p. 8 — 1.3–1.4;1.10 items1–6;1.12.1 complete diagrams and sequence.

Part numbers (9)
  • 4134 180 6700 — Previous retainer assembly including items 2–4Remains older-machine spare · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 180 6701 — Previous upper retainerRemains older-machine spare · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 180 6702 — New upper retainerTwo-wire system · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 182 2105 — Previous lower retainerRemains older-machine spare · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 182 2104 — New lower retainerConnector recess · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 9075 478 4159 — IS-D5x24 screwUnchanged number · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 9291 021 0120 — DIN125-A5.3 washerUnder screw head · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 440 1100 — Old sheath-contact short-circuit wireRemains older-machine spare · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 440 1101 — New plug-connected short-circuit wireRetainer to ignition module · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only

Conditional replacement · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C

TI 09: two-wire cable changes housing and removes old ground plate

Contact plate, gasket and ignition-lead retainer are deleted only for the new system.

  • Carburetor housing 4134 120 0101 becomes 4134 120 0102 for intake airflow and the new cable-sheath-end seat; shaded areas in250TI046 identify the old/new seat. The modified cable end also needs the matching carburetor pin. New carburetors are supplied with the new pin from initial series production; this does not resolve the opposite retrofit directions on pages8 and16.
  • Contact plate 4134 431 7000 and gasket 4128 129 0900 are no longer required with the TWO separate short-circuit wires. They previously grounded the short block in the cable-sheath system WITHOUT separate wires, as described in TI 42/2002. Grounding now uses the new retainer. Do not remove the plate/gasket from an otherwise unchanged old cable-based STOP system.
  • Cylinder-mounted ignition-lead retainer 4134 448 1200 is no longer needed with the new throttle-cable retainer. Section 1.11 permits removing the old contact plate with gasket and lead retainer when the complete new handle/cable package is installed. All four previous parts in items 7–10 remain spares for older machines, despite deletion from the new configuration.
  • USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.

Source: TI 9/2003, p. 4 · TI 9/2003, p. 5 · TI 9/2003, p. 7 · TI 9/2003, p. 8 — 1.5–1.8;1.10 items7–10;1.11–1.12.2.

Part numbers (5)
  • 4134 120 0101 — Previous carburetor housingOlder-machine spare · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 120 0102 — New carburetor housingModified sheath seat · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 431 7000 — Old ground contact plateDeleted only with new two-wire cable · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4128 129 0900 — Contact-plate gasketDeleted only with new two-wire cable · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 448 1200 — Ignition-lead retainerDeleted with new throttle retainer · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only

Conditional replacement · FS 120 / FS 200 / FS 250 / FS 350 / FS 120 R / FS 200 R / FS 250 R / BT 120 C

TI 09: conversion prerequisites reviewed, pin choice still unresolved

Control and carburetor conversions remain separate; reviewed dependencies do not prove universal interchange.

  • Section 1.11 control conversion requires NEW control-handle assembly, cable assembly, cable retainer, retainer-to-ignition short-circuit wire, carburetor housing and appropriate carburetor pin. Only with that package may the old contact plate/gasket and ignition-lead retainer be removed. It explicitly requires reading TI 21/2000, TI 22/2001, TI 42/2002; all three are now reviewed, not missing sources.
  • TI 21/2000 intake-grounding/gasket/stud changes and TI 42/2002 contact-plate/longer-stud requirement apply to their documented older configurations. TI 42 requires the plate for cable-based STOP WITHOUT separate wires; TI 09 deletes it WITH the complete two-wire system. These are conditional configurations, not a contradiction permitting removal from every old machine.
  • TI 22/2001 preserves old housing0100 on two-boss cylinders, new housing0101 with its third boss/bushing, model-specific shrouds and cooling dependencies, ignition washers, and longer-screw/wire-holder requirement for its earlier retainer. TI 09 specifies housing0102 and a later retainer package; it does NOT supply a universal two-boss-to-0102 adaptation. Do not bypass the earlier cylinder/mount restrictions or mix the two generations of retainer repair instructions.
  • Section 2.4 carburetor conversion separately requires carburetor assembly, matching pin and shroud; old guide grommet may be removed and older machines receive the appropriate label from sheet 4134 967 1514. TI 22 section 6 establishes that sheet as model-selectable labels, not approval for every illustrated model. Its FS 120/200 index-C clutch-shroud and FS 350 cooling-cover dependencies remain model scoped; do not extend them to BT 120 C or assume unspecified FS 250 exceptions away.
  • Pin ambiguity remains UNRESOLVED: page 8 says8900 to 8901 for the new cable on C1Q-S35/S36/S51; page 16 says8901 to 8900 and repeats those old carburetor names in its new-carburetor context. No winner, corrected model name, or universal pin is established. Keep both instructions and inspect the actual cable/carburetor combination before selecting a conversion; this review does not establish a fully executable conversion for every older variant.
  • Printed page 16 references3.2 and TI 22.2201 remain erroneous/ambiguous locators; actual shroud heading is2.2, and the separately explicit page 7 TI 22.2001 reference is retained. Dependency review does not silently repair the printed citation. Section 2.4 then calls for cable attachment and carburetor adjustment; section 2.4.2 requires the replacement user adjustment instructions already reviewed with section 2.
  • All locally available TI 09 assertions and named dependency material are dispositioned. Source conflicts remain documented, not resolved by semantic closure; no missing-source gap or physical interchange proof is invented.
  • USA production introduction is in progress, without a numeric cutoff. Factory availability describes the bulletin date, not current stock. Shared catalog sheets do not extend the stated model/handle/configuration scope. No physical interchange test was performed.

Source: TI 9/2003, p. 1 · TI 9/2003, p. 2 · TI 9/2003, p. 4 · TI 9/2003, p. 7 · TI 9/2003, p. 8 · TI 9/2003, p. 16 — 1 introduction;1.11–1.12.2;2.4–2.4.1 with reviewed TI21/2000 TI22/2001 TI42/2002 dependencies.

Part numbers (3)
  • 4128 121 8900 — Pin5Page 8 previous; page 16 replacement · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4128 121 8901 — Pin6Page 8 replacement; page 16 previous · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only
  • 4134 967 1514 — Model-label sheetSelect actual machine label · FS 120, FS 200, FS 250, FS 350, FS 120 R, FS 200 R, FS 250 R, BT 120 C; stated configuration only

Service note · FS 120 / FS 200 / FS 350 / FS 400 / FS 450

FS120/200/350/400/450: paper filter and compensator system

Larger filter area and carburetor pressure compensation are paired features.

  • New longlife air-filter system uses a PAPER FILTER ELEMENT with larger effective surface area. Carburetor compensator offsets pressure changes as the filter loads with dirt; this is not permission to operate with a missing or damaged filter.
  • Drawing250TI007 KN shows cover, pleated element, filter housing and carburetor with COMPENSATOR STUB. It supplies no part numbers, washing method, replacement interval or universal retrofit dimensions. One adjusting screw is stated; original carburetor-specific details are separate.
  • No filter from predecessor FS88/108/160/180/220/280 is declared interchangeable. Feature evidence does not equate later carburetor revisions with C1Q-S34A/C1Q-S36B.
  • Historical TI42/1997 configurations only, not all later versions sharing a model name. No hardware operation was performed. No part interchange or numeric serial cutoff is established.

Source: TI 42/1997, p. 2 — Section1 carburetor/air-filter description and full250TI007 KN illustration.

No additional parts-table entry added.

Service note · FS 120 / FS 200 / FS 350 / FS 450

FS 120 / 200 / 350 / 450: match throttle-cable nipple and carburetor pin

Original replacement cables retain their numbers; fitting one to a new-style machine requires the supplied original pin.

  • The heading explicitly names FS 120, 200, 350 (series 4134) and FS 450 (series 4128). Section 1.1 announces a new cable nipple WITH A COLLAR and a new carburetor pin WITH A THROUGHHOLE in the near future. The table has additional model names, preserved separately in the two carburetor notes rather than silently changing this heading.
  • Figure 250TI018 KN shows the ORIGINAL attachment: nipple (1), pin (2), cable (3), carburetor (4). Figure 250TI019 KN compares original nipple (1) with original pin (2), and new collared nipple (5) with new pin (6). These are figure callouts, not summary-table item numbers: table item 5 is the original pin, not the new nipple.
  • New carburetors are equipped with the new pin (6) and ALSO supplied with original pin (2). The instructions determine which pin to use according to the cable nipple. The original pin is 4128 121 8900; the new pin is 4128 121 8901. Supplying both does not authorize mixing the illustrated nipple/pin pairs.
  • Replacement throttle cables with the ORIGINAL nipple WITHOUT COLLAR remain available and come with original pin (2) and an instruction sheet. Their PART NUMBERS REMAIN UNCHANGED; no actual cable number is printed, so none is inferred from the later catalog. When fitting this original-style replacement cable to a machine supplied with the new nipple, REPLACE new pin (6) on the carburetor with supplied original pin (2). This is not a direction to remove a collar from the cable.
  • Section 1.3 requires the original cable nipple to be properly seated in the carburetor pin. Adjust the cable exactly as described in the SERVICE MANUAL. When correctly adjusted, the nipple must NOT JUMP OUT when the throttle trigger is suddenly released from the fully open position. The manual and instruction-sheet referrals are retained; this bulletin does not supply the full adjustment procedure or authorize a running-engine test.
  • The introduction line says THROTTLE CABLES: IN PROGRESS, with no serial or date boundary. A same-number cable cannot be dated or identified by number alone. All other parts as before. The last-TI references (FS 120/200:42.97; FS 350/450:20.98), copyright 1998 and documentation 6334 are bibliography, not changeover serials.
  • The later catalog housing sheets are model context, not proof that all carburetor revisions use the same attachment. Shared sheets include FS 120R/200R/250 and FS 480; those variants are not added to the bulletin’s named models. Prior conflicts remain unchanged.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 19/1998, p. 1 · TI 19/1998, p. 2 — Page 1 sections 1.1–1.2 and both figures; page 2 complete service note1.3, introduction and footer.

Part numbers (2)
  • 4128 121 8900 — Original carburetor attachment pinMatch original nipple without collar · Original-style replacement throttle cable
  • 4128 121 8901 — New carburetor attachment pinMatch new collared nipple · New-style cable attachment

Historical fitment · FS 120 / FS 200 / FS 300 / FS 350 / FR 350

FS 120 / 200 / 300 / 350, FR 350: three C1Q-S36 revisions

Original S36B, interim S36C and new S36D retain distinct numbers and supplied grommet/pin contents.

  • The first summary group explicitly names FS 120, 200, 300, 350 and FR 350. FS 300 and FR 350 are absent from the shorter page 1 heading but present in this table; retain the group exactly. No FR 350 IPL sheet was found in the canonical local parts dataset; its applicability is supported by the TI table, not an invented assembly binding.
  • ORIGINAL: C1Q-S36B, 4134 120 0601, includes item 5 (original pin 8900). INTERIM: C1Q-S36C, 4134 120 0650, includes items 4 and 5 (grommet 7502 and original pin 8900). NEW: C1Q-S36D, 4134 120 0651, includes items 4, 5, 6 (grommet 7502 and BOTH original/new pins 8900/8901). These are three distinct supplied configurations, not an undifferentiated two-part supersession.
  • Table item 4 grommet 4134 123 7502 is a dash in the original column and has the same number in interim and new columns. Item5 original pin 4128 121 8900 is listed in ALL THREE columns. Item6 new pin 4128 121 8901 is listed ONLY in the new column. Included original pin remains available with the new carburetor for the matching original nipple.
  • Remark1 attaches to original S36B: no longer available FROM FACTORY. Remark2 attaches to interim S36C: supplied from factory ONLY AS LONG AS EXISTING STOCKS LAST. Neither remark establishes current stock, a production date, or universal bare-carburetor interchange. New pin matching and cable adjustment restrictions remain applicable.
  • The retained SCS 01-2012 USA housing sheets list 4134 120 0651 as C1Q-S51C, not this 1998 C1Q-S36D designation. The shared number is retained as an edition/designation difference, not silently relabeled or proof of identical internals. Later S161/S162/S163/S164 alternatives do not rewrite this historical three-column table. No FS 250, R-variant or BT120C approval is inferred from shared later parts.
  • Historical source guidance; no present-day stock guarantee or verified physical interchange. No hardware operation was performed.

Source: TI 19/1998, p. 1 · TI 19/1998, p. 2 — Page 2 section 1.4 first group, rows 1–6 and remarks; page 1 pairing context.

Part numbers (6)
  • 4134 120 0601 — Carburetor C1Q-S36BOriginal; includes item 5 · FS 120 / 200 / 300 / 350 and FR 350 summary group
  • 4134 120 0650 — Carburetor C1Q-S36CInterim; includes items 4, 5 · FS 120 / 200 / 300 / 350 and FR 350 summary group
  • 4134 120 0651 — Carburetor C1Q-S36DNew; includes items 4, 5, 6 · FS 120 / 200 / 300 / 350 and FR 350 summary group
  • 4134 123 7502 — GrommetSame interim/new number · FS 120 / 200 / 300 / 350 and FR 350 summary group
  • 4128 121 8900 — Original pinIncluded in all three versions · FS 120 / 200 / 300 / 350 and FR 350 summary group
  • 4128 121 8901 — New pinAdditional pin in new version · FS 120 / 200 / 300 / 350 and FR 350 summary group

Wrong number or missing part for the FS 300, FS 350? Report a correction →