← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section A · 1 of 15 · 28 parts

Crankcase, Cylinder

Fits FR 108.

Parts diagrams →

Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151616171819222021222333445677889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4135 020 2600 Crankcase, fan side 1
2 9380 620 2570 Roll pin 5x12 4
3 9503 003 0242 Grooved ball bearing 6201 2
4 9640 003 1195 Oil seal 12x22x5 2
5 4135 020 2800 Crankcase, starter side 1
6 4135 030 0400 Crankshaft 1
7 0000 958 1222 Shim 0.1 mm
8 0000 958 1223 Shim 0.2 mm
9 9022 341 1070 Spline screw IS-M5x30 4
10 4112 036 8600 Woodruff key 1
11 4126 084 2200 Guard 1
12 4135 022 0500 Cylinder Ø 37 mm 1
13 4135 034 0500 Piston Ø 37 mm 1
14 4129 034 3000 Piston ring Ø 37x1.5 mm 2
15 4117 034 1500 Piston pin 10x7x30 1
16 9463 650 1000 Snap ring 10 2
17 9512 003 2340 Needle cage 10x14x13 1
18 4135 029 2300 Cylinder gasket 1
19 9022 341 0980 Spline screw IS-M5x16 4
20 0000 400 7000 Spark plug NGK BPMR7A 1
20 1110 400 7005 Spark plug Bosch WSR 6 F 1
21 0000 998 0606 Torsion spring 1
22 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
23 4135 149 0600 Muffler gasket 1
Not numbered on the diagram — assemblies, kits and options
— 4135 020 1200 Cylinder with piston Ø 37 mm 1
— 4135 030 2000 Piston Ø 37 mm 1
— 0783 830 2000 Tube of sealant Dirko HT red not illustrated 1
— 4135 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 108

FR 108: two-stroke construction and two-stage filter

Die-cast crankcase, two-ring piston and foam/felt filter; FR 106 design ancestry is not blanket parts interchange.

  • Professional backpack brushcutter based on the FR 106 design concept; source claims the same 1.1 kW (1.5 bhp), increased torque and easier servicing, and approximately 0.5 kg (1.1 lb) less weight. These comparisons have not been independently tested. Photograph 360 TI 001 shows a configuration, not a complete supplied-parts inventory.
  • Compact two-stroke powerhead has smooth exterior surfaces to reduce dirt accumulation and aid cleaning; housing helps prevent contact with hot engine parts. Crankcase is a two-part aluminum die casting with two dust-lip oil seals. Crankshaft is a three-part assembly pressed together before final machining.
  • Aluminum-alloy piston has TWO compression rings; piston pin runs in a needle cage and is retained by hookless wire snap rings. Special aluminum-alloy cylinder has an electroplated wear-resistant bore; the coating composition is not specified.
  • Diaphragm carburetor mounts to the cylinder with thermal insulation. Air filter illustration 357 TI 004: flat foam element (1), felt element (2), tool-free removable/refittable cover (3). Large-volume muffler has a fire screen. These diagram keys are not current IPL drawing positions.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 1 · TI 4/1995, p. 2 · TI 4/1995, p. 3 — two-stroke construction and two-stage filter.

No additional parts-table entry added.

Service note · FR 108

FR 108: engine, fuel and starter specifications

34.4 cc /37 x 32 mm; 3.5 x 800 mm starter rope, seven spring turns and minimum half-turn spare travel.

  • Powerhead: displacement 34.4 cm³ (2.1 cu.in), bore 37 mm (1.46 in), stroke 32 mm (1.26 in), engine power to ISO 8893 1.1 kW (1.5 bhp). Weight 10.3 kg (22.7 lb) EXCLUDES cutting tool and deflector.
  • Printed full-load engine speed WITHOUT CUTTING TOOL 12,000 rpm; output shaft maximum 9,000 rpm; clutch engagement 3,500 rpm; idle 2,800 rpm. These are distinct historical specifications, not authorization to run an unattended machine.
  • Single-pawl rewind starter: spring tension 7 turns of rope rotor, spare travel MINIMUM 1/2 turn. Starter rope diameter 3.5 mm (0.14 in), length 800 mm (31.5 in). Retained FR 108 sheet B agrees on 3.5 x 800 mm; bulk-rope roll length is not installed-rope length.
  • Fuel system uses foam and felt filter elements; fuel capacity 0.69 l (1.45 US pt). No fuel/oil mixture ratio is supplied on these specification pages. Approved cutting tools are those in section 2, not inferred from engine power.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 4 · TI 4/1995, p. 5 — engine, fuel and starter specifications.

No additional parts-table entry added.

Service note · FR 108

FR 108: ignition settings and lead-length difference

0.1–0.5 mm air gap, timing at 8,000 rpm; TI lead 220 mm differs from retained IPL 175 mm.

  • Electronic ignition consists of flywheel and module with integral trigger unit. Flywheel need not be removed for access to the ignition module; this is not a complete removal procedure.
  • Air gap 0.1–0.5 mm (0.004–0.020 in). Ignition timing 1.45–2.05 mm (0.06–0.08 in) B.T.D.C. at 8,000 rpm. These millimetres before top dead centre are NOT crankshaft degrees.
  • Suppressed spark plug: Bosch WSR 6 F OR NGK BPMR 7 A; printed heat range 200; electrode gap 0.5 mm (0.020 in); M 14 x 1.25 thread, length 9.5 mm (0.37 in). The TI does not supply plug order numbers.
  • Printed ignition lead length 220 mm (8¾ in) differs from retained 2012 FR 108 ignition sheet C item 5, lead 175 mm. Preserve this unresolved edition/configuration difference; do not silently replace either value or infer a cutting instruction.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 3 · TI 4/1995, p. 5 — ignition settings and lead-length difference.

No additional parts-table entry added.

Service note · FR 108

FR 108: carburetor kit and crankcase sealant differences

TI 4132 007 1061 and Dirko 0783 830 2120 differ from later FR 108 IPL material numbers.

  • Section 4.5.2 lists carburetor parts kit 4132 007 1061 without an individual carburetor model or kit-content breakdown. Retained FR 108 carburetor sheets F(SK 5/C 1 Q-SK 5) and G(C 1 Q-SK 7 USA) instead list set 4134 007 1060. Keep the conflict visible; do not claim the 1995 kit fits every later carburetor or infer a supersession.
  • Dirko sealant 0783 830 2120 is specified for sealing the crankcase. Later FR 108 sheets A/P list Dirko HT red 0783 830 2000. No replacement relationship or chemical equivalence is established by this TI. No tube size, curing time or sealant application procedure is supplied here.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 7 — carburetor kit and crankcase sealant differences.

Part numbers (2)
  • 4132 007 1061 — Carburetor parts kitprinted 1995 kit; model contents unspecified · FR 108; TI 04/1995 conditions
  • 0783 830 2120 — Dirko sealantcrankcase sealing · FR 108; TI 04/1995 conditions

Service note · FR 108

FR 108: carburetor basic settings and separate leak tests

H/L one turn; carb closing pressure 0.8 bar versus crankcase pressure/vacuum 0.5 bar; not a complete repair procedure.

  • Historical basic setting: high-speed H and low-speed L screws each back off ONE full turn. Source wording says initially “hard against their seats”; preserve it as a dated quotation, not a new instruction to force or damage an adjustment seat. Verify the actual carburetor and applicable service procedure; the TI supplies no carburetor model designation or limiter-cap instructions here.
  • Full-load engine speed WITHOUT CUTTING TOOL 12,000 rpm; idle 2,800 rpm. Carburetor leakage-test closing pressure 0.8 bar (11.6 psi). Crankcase leakage test: gauge pressure 0.5 bar (7.25 psi), vacuum 0.5 bar (7.25 psi). Vacuum is a magnitude, not a positive-pressure test. No hold time or allowed leakage rate is supplied here.
  • Page 11 requires the FR 108 service manual for service/repair and all local/national safety rules plus owner-manual precautions if started during repair. It says carburetor servicing, troubleshooting and other standard repairs are omitted from the new manual and planned for a separate handbook; appropriate FR/FS 106 manual chapters are the stated interim reference. This note does not supply or verify those missing procedures, and the complete TI/manual-dependency disposition is now recorded in the accompanying repair-manual boundaries note; exact missing procedures remain source gaps.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 7 · TI 4/1995, p. 11 — carburetor basic settings and separate leak tests.

No additional parts-table entry added.

Service note · FR 108

FR 108: engine fastener torque table

Fastener size AND component determine torque; two tensioner rows are unspecified, not zero.

  • Table values below retain the printed Nm / lbf.ft pair, not recalculated conversions. Size alone does not select the torque: IS-M 5x16 has several component-specific values. Spline screws unless otherwise named.
  • Crankcase, IS-M 5x30: 10.5 / 7.7. Cylinder to crankcase, IS-M 5x16: 10.0 / 7.4. Clutch shoes, hex-head M8x20: 17.0 / 12.5. Muffler to cylinder, IS-M 5x16: 10.5 / 7.7. Muffler to crankcase, IS-M 5x12: 10.5 / 7.7. Cover plate to muffler, IS-M 4x12: 3.5 / 2.6.
  • Clutch housing, IS-M 5x16: 9.5 / 7.0. Support to clutch housing, IS-M 5x16: 7.5 / 5.5. Fuel tank, flange screw IS-M 5x14: 5.5 / 4.0. Flywheel, hexagon nut M8: 17.0 / 12.5. Carrier, hexagon nut M8: 17.0 / 12.5.
  • Starter cover TOP, IS-M 5x16: 5.5 / 4.0. Support/starter cover BOTTOM, IS-M 5x16: 7.5 / 5.5. Rope rotor, special spline IS-P 5.5x12: 2.5 / 1.8. Ignition module, IS-M 5x20: 7.5 / 5.5. Spark plug, M14x1.25: 19.0 / 14.0.
  • Carburetor, IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder, IS-M 5x25: 5.5 / 4.0. Adjusting screw in tensioner, IS-M 4x25: DASH. Tensioner to spacer flange, IS-M 5x16: DASH. Both dashes mean no torque specified in this table, NOT zero and not permission to substitute an all-others value. The source labels these tensioner rows even though this is a brushcutter; preserve the wording without inventing a component identity or correction.
  • No tightening sequence, reuse criteria, lubrication or thread-locking rule is supplied by this table. Use the applicable service procedure for the actual configuration.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 8 — engine fastener torque table.

No additional parts-table entry added.

Service note · FR 108

FR 108: piston, seal and leakage-test tools

Starter-side seal protection and installation use different sleeves; leak-test equipment is not a test procedure.

  • 4112 893 1200 — Piston locking screw: blocking crankshaft; 1129 893 2400 — Press sleeve: installing clutch-side oil seal; 4112 893 2400 — Press sleeve: PROTECTING starter-side oil seal; 1115 893 4600 — Press sleeve: INSTALLING starter-side oil seal; 4117 893 4700 — Press arbor: installing piston pin; 0000 893 2600 — Clamping strap: compressing piston rings; 1108 893 4800 — Wooden assembly block: fitting piston; 1106 850 2905 — Crankcase and carburetor tester: testing crankcase and carburetor for leaks; 0000 855 9200 — Nipple: carburetor leakage test; 1110 141 8600 — Fuel line: carburetor leakage test; 0000 850 3501 — Vacuum pump: crankcase leakage test; 0000 855 8106 — Sealing plate: sealing exhaust port for leakage test.
  • The nipple and fuel line are subordinate tester accessories in the source table, not a machine fuel-line fitment declaration. PROTECTING the starter-side seal with 4112 893 2400 is distinct from INSTALLING it with 1115 893 4600. No removal/assembly sequence, fixture setup or leak-test hold time is supplied in this roster.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 9 — piston, seal and leakage-test tools.

Part numbers (12)
  • 4112 893 1200 — Piston locking screwblocking crankshaft · FR 108; TI 04/1995 conditions
  • 1129 893 2400 — Press sleeveinstalling clutch-side oil seal · FR 108; TI 04/1995 conditions
  • 4112 893 2400 — Press sleevePROTECTING starter-side oil seal · FR 108; TI 04/1995 conditions
  • 1115 893 4600 — Press sleeveINSTALLING starter-side oil seal · FR 108; TI 04/1995 conditions
  • 4117 893 4700 — Press arborinstalling piston pin · FR 108; TI 04/1995 conditions
  • 0000 893 2600 — Clamping strapcompressing piston rings · FR 108; TI 04/1995 conditions
  • 1108 893 4800 — Wooden assembly blockfitting piston · FR 108; TI 04/1995 conditions
  • 1106 850 2905 — Crankcase and carburetor testertesting crankcase and carburetor for leaks · FR 108; TI 04/1995 conditions
  • 0000 855 9200 — Nipplecarburetor leakage test · FR 108; TI 04/1995 conditions
  • 1110 141 8600 — Fuel linecarburetor leakage test · FR 108; TI 04/1995 conditions
  • 0000 850 3501 — Vacuum pumpcrankcase leakage test · FR 108; TI 04/1995 conditions
  • 0000 855 8106 — Sealing platesealing exhaust port for leakage test · FR 108; TI 04/1995 conditions

Service note · FR 108

FR 108: workshop-tool roster and three explicit alternatives

Flange, air-gap gauge and circlip-plier alternatives stay conditional; signal-equipped wrenches are distinct.

  • 1113 850 4200 — Test flange: leakage test; 1128 850 4200 — Alternative test flange: footnote 1 alternative to 1113 850 4200; 1111 890 6400 — Setting gauge: ignition module/flywheel air gap; 4118 890 6401 — Alternative setting gauge: footnote 2 alternative to 1111 890 6400; 0000 890 4400 — Puller: removing oil seals; 0000 893 3706 — Jaws profile 3.1: for oil-seal puller; 5910 890 2210 — Installing tool 10: hookless piston snap rings; 5910 893 5608 — Socket 13 mm: crankshaft nut: carrier/flywheel; 5910 890 0301 — Torque wrench: 0.5 to 18 Nm; 5910 890 0302 — Torque wrench: 0.5 to 18 Nm; optical/acoustical signal; 5910 890 0311 — Torque wrench: 6 to 80 Nm; 5910 890 0312 — Torque wrench: 6 to 80 Nm; optical/acoustical signal; 5910 893 8800 — Assembly hook: removing pickup body; 5910 890 2400 — T-handle screwdriver QI-T27x150: IS spline screws; 5910 890 8210 — Crimping tool: wire connectors and lugs; 5910 850 3100 — Assembly stand: holds powerhead for repair; 5910 893 2500 — Flange: assembly stand accessory; 5910 890 2100 — Clamping plate: settings as for FS 106 or FS 108; 0812 542 2104 — Socket: cylinder base screws; 4119 893 7200 — Press arbor: removing/installing main bearings; 0811 641 8380 — Pliers C19: INTERNAL gearhead circlips; 0816 630 1452 — C8 pliers: footnote 5 alternative to C19 pliers; 0811 611 8200 — Pliers A10: EXTERNAL circlips: clutch drum, gearhead, drive pinion; 0816 610 1495 — Circlip pliers: EXTERNAL clutch-drum circlips; 1108 893 4700 — Press arbor: removing clutch drum; 1118 893 7200 — Press arbor: removing/installing ball bearing in clutch housing.
  • Footnotes permit ONLY the stated alternatives: flange 1128 850 4200 for 1113 850 4200; gauge 4118 890 6401 for 1111 890 6400; C8 pliers 0816 630 1452 for C19 pliers 0811 641 8380. These are historical tool alternatives, not blanket machine-part interchange.
  • Footnote 4, optical/acoustical signal, attaches to torque wrenches 5910 890 0302 and 5910 890 0312, not all four wrench identifiers. The two ranges are 0.5–18 Nm and 6–80 Nm respectively. Assembly-stand accessory settings are referenced as for FS 106 or FS 108; actual setup dimensions are not provided here.
  • Removing tool 4119 890 4600 is separately documented with its MANDATORY modification drawing; it must not be treated as an unrestricted tool from this roster. Neither roster nor generic tool name supplies a complete repair procedure.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 10 — workshop-tool roster and three explicit alternatives.

Part numbers (26)
  • 1113 850 4200 — Test flangeleakage test · FR 108; TI 04/1995 conditions
  • 1128 850 4200 — Alternative test flangefootnote 1 alternative to 1113 850 4200 · FR 108; TI 04/1995 conditions
  • 1111 890 6400 — Setting gaugeignition module/flywheel air gap · FR 108; TI 04/1995 conditions
  • 4118 890 6401 — Alternative setting gaugefootnote 2 alternative to 1111 890 6400 · FR 108; TI 04/1995 conditions
  • 0000 890 4400 — Pullerremoving oil seals · FR 108; TI 04/1995 conditions
  • 0000 893 3706 — Jaws profile 3.1for oil-seal puller · FR 108; TI 04/1995 conditions
  • 5910 890 2210 — Installing tool 10hookless piston snap rings · FR 108; TI 04/1995 conditions
  • 5910 893 5608 — Socket 13 mmcrankshaft nut: carrier/flywheel · FR 108; TI 04/1995 conditions
  • 5910 890 0301 — Torque wrench0.5 to 18 Nm · FR 108; TI 04/1995 conditions
  • 5910 890 0302 — Torque wrench0.5 to 18 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
  • 5910 890 0311 — Torque wrench6 to 80 Nm · FR 108; TI 04/1995 conditions
  • 5910 890 0312 — Torque wrench6 to 80 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
  • 5910 893 8800 — Assembly hookremoving pickup body · FR 108; TI 04/1995 conditions
  • 5910 890 2400 — T-handle screwdriver QI-T27x150IS spline screws · FR 108; TI 04/1995 conditions
  • 5910 890 8210 — Crimping toolwire connectors and lugs · FR 108; TI 04/1995 conditions
  • 5910 850 3100 — Assembly standholds powerhead for repair · FR 108; TI 04/1995 conditions
  • 5910 893 2500 — Flangeassembly stand accessory · FR 108; TI 04/1995 conditions
  • 5910 890 2100 — Clamping platesettings as for FS 106 or FS 108 · FR 108; TI 04/1995 conditions
  • 0812 542 2104 — Socketcylinder base screws · FR 108; TI 04/1995 conditions
  • 4119 893 7200 — Press arborremoving/installing main bearings · FR 108; TI 04/1995 conditions
  • 0811 641 8380 — Pliers C19INTERNAL gearhead circlips · FR 108; TI 04/1995 conditions
  • 0816 630 1452 — C8 pliersfootnote 5 alternative to C19 pliers · FR 108; TI 04/1995 conditions
  • 0811 611 8200 — Pliers A10EXTERNAL circlips: clutch drum, gearhead, drive pinion · FR 108; TI 04/1995 conditions
  • 0816 610 1495 — Circlip pliersEXTERNAL clutch-drum circlips · FR 108; TI 04/1995 conditions
  • 1108 893 4700 — Press arborremoving clutch drum · FR 108; TI 04/1995 conditions
  • 1118 893 7200 — Press arborremoving/installing ball bearing in clutch housing · FR 108; TI 04/1995 conditions

Service note · FR 108

FR 108: crankshaft removing tool requires modification

4119 890 4600: mandatory historical drawing 357TI009; dimensions do not authorize a hardware operation.

  • Removing tool 4119 890 4600 is for removing the crankshaft at the STARTER SIDE. Footnote 3: existing tools MUST be modified as shown in illustration 357TI009. The source says the modification does not affect or restrict the tool’s OTHER applications; it does not waive the modification for this FR 108 job.
  • Drawing 357TI009 is the geometry authority. Left marked-hole centre to central opening: 45 ±0.2; central opening to right indicated centre line: 47 ±0.2. Left marked-hole centre line lies 8.5 below top edge. Right detail shows 2.5 ±0.2 vertical offset, slot width 6, centre spacing 3.2, angle 51° ±2°, and end radius r without a numerical radius value. Decimal commas are rendered as decimal points. The drawing does not print a length-unit legend on this page; do not silently promote an assumed unit, derived slot length or radius into an explicit source dimension.
  • The angled slot, offset and centre datums must be read together from the linked drawing, not reconstructed from a prose list alone. No complete manufacturing specification, tool material, tolerance on every feature or repair sequence is supplied. No tool modification or hardware operation has been carried out.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 10 — crankshaft removing tool requires modification.

Part numbers (1)
  • 4119 890 4600 — Crankshaft removing toolstarter side; existing tool MUST be modified · FR 108; TI 04/1995 conditions

Service note · FR 108

FR 108: repair-manual boundaries and operating precautions

The new manual omits carburetor servicing, troubleshooting and standard repairs; FR/FS106 chapters are the historical interim reference.

  • If started during repairs or maintenance, the unit requires strict observance of ALL local and national safety regulations AND the owner-manual safety precautions. This source statement is retained; it is not permission for unattended startup or a replacement for the actual owner manual.
  • For FR 108 servicing and repair, section 8 refers to its service manual. The new manual omits “Servicing the Carburetor”, “Troubleshooting” and other standard repair jobs. A separate handbook is described as forthcoming in 1995; appropriate chapters of the FR and FS 106 service manual are the stated INTERIM reference until that handbook is published.
  • Local dependency review searched the retained STIHL service documentation manual catalog and first-three-page PDF covers, including separately organized service manuals and RA/HB resources. The exact FS 88/108/FR 108 shop manual and FR/FS 106 interim manual were not identified. No edition of the unnamed forthcoming handbook is established by this TI; similarly titled later material is not automatically that edition. These are scoped source gaps, not proof that the documents never existed.
  • The available TI dimensions, torque and repair-time tables do not replace the missing procedures. Whole-manual review/import is a separate follow-on phase; none of these manuals is claimed imported or accepted here. Footer identifies Waiblingen, 22.02.1995; ©1995 Andreas Stihl; Technical Documentation, D1/MTK-na. Publication date is not a serial changeover.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 9 · TI 4/1995, p. 11 — repair-manual boundaries and operating precautions.

No additional parts-table entry added.

Service note · FR 108

FR 108: twenty historical workshop repair times

Tenths of an hour, not clock-minute decimals; trained staff and an equipped workshop are prerequisites.

  • Table header explicitly names FS 88, FS 108 and FR 108. All values are HOURS expressed in tenths: 0.1 hour = 6 minutes. Values assume trained personnel in a properly equipped service workshop; they are historical labor allowances, not guaranteed owner repair durations, prices or mandatory service intervals.
  • 1 Crankcase, Short Block: 2.1 h; 2 Crankshaft and/or Bearings: 2.2 h; 3 Crankcase Gasket, Sealing: 2.0 h; 4 Crankshaft seals: 0.7 h; 5 Cylinder and/or Piston: 0.8 h; 6 Ignition: 0.5 h; 7 Fuel Hose, Fuel Supply: 0.5 h; 8 Gear Box, Arbor Assy: 0.6 h; 9 Carburetor: 0.7 h; 10 Fan Housing, Clutch Housing: 0.8 h; 11 Front Handle, Throttle: 0.6 h; 12 Recoil Starter: 0.5 h; 13 Clutch: 0.5 h; 14 Drive Tube, Drive Shaft: 0.5 h; 15 Muffler: 0.4 h; 16 Air Filter, Filter Cover: 0.3 h; 17 Stop Switch: 0.4 h; 18 Fuel Tank: 0.4 h; 19 Replace Arbor Gears: 0.8 h; 20 Misc. Repairs: 0.5 h.
  • The TI says this table for the new brushcutters can be added to the STIHL repair-times table. The cut-out border/scissors mark is a layout aid, not another repair instruction. Model names in this table do not establish parts interchange or authorize extending the FR 108 torque table to FS models.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 11 — twenty historical workshop repair times.

No additional parts-table entry added.

Wrong number or missing part for the FR 108? Report a correction →