← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section B · 2 of 15 · 28 parts

Rewind starter, Muffler

Fits FR 108.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161717181922021222324253456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4129 190 2000 Carrier 1
2 4215 195 7200 Pawl 1
3 0000 998 0607 Torsion spring 1
4 9460 624 0400 E-clip 4 1
5 9443 825 7070 Hollow rivet 7.15x0.4x3 1
6 9210 260 1100 Hexagon nut M8 1
7 4126 190 0405 Starter cover 1
8 not sold separately Hollow rivet 6.5x0.5x5.8 not available as a separate item 4
9 4126 084 9100 Bushing 1
10 4126 195 1600 Rewind spring 1
11 4215 195 0400 Rope rotor 1
12 4117 195 8200 Starter rope Ø 3.5x800 mm 1
13 4215 195 9000 Washer 1
14 9104 003 0960 Self-tapping screw P5.5x12 1
15 4117 195 3400 Starter grip 1
16 4135 967 1501 Model plate FR 108 1
17 9022 341 0980 Spline screw IS-M5x16 6
18 4135 149 0600 Muffler gasket 1
19 4135 140 0600 Muffler 1
20 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 1
21 4135 149 0605 Muffler gasket 1
22 4135 145 1000 Insert 1
23 1113 141 9000 NLA Screen 1
24 4135 146 7300 Cover plate 1
25 9022 313 0610 Spline screw IS-M4x6 4
Not numbered on the diagram — assemblies, kits and options
— 4126 190 4000 Rewind starter 1
— 0000 930 2203 Starter rope Ø 3.5 mm x 30.5 m not illustratedoption 1
— 4135 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 108

FR 108: two-stroke construction and two-stage filter

Die-cast crankcase, two-ring piston and foam/felt filter; FR 106 design ancestry is not blanket parts interchange.

  • Professional backpack brushcutter based on the FR 106 design concept; source claims the same 1.1 kW (1.5 bhp), increased torque and easier servicing, and approximately 0.5 kg (1.1 lb) less weight. These comparisons have not been independently tested. Photograph 360 TI 001 shows a configuration, not a complete supplied-parts inventory.
  • Compact two-stroke powerhead has smooth exterior surfaces to reduce dirt accumulation and aid cleaning; housing helps prevent contact with hot engine parts. Crankcase is a two-part aluminum die casting with two dust-lip oil seals. Crankshaft is a three-part assembly pressed together before final machining.
  • Aluminum-alloy piston has TWO compression rings; piston pin runs in a needle cage and is retained by hookless wire snap rings. Special aluminum-alloy cylinder has an electroplated wear-resistant bore; the coating composition is not specified.
  • Diaphragm carburetor mounts to the cylinder with thermal insulation. Air filter illustration 357 TI 004: flat foam element (1), felt element (2), tool-free removable/refittable cover (3). Large-volume muffler has a fire screen. These diagram keys are not current IPL drawing positions.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 1 · TI 4/1995, p. 2 · TI 4/1995, p. 3 — two-stroke construction and two-stage filter.

No additional parts-table entry added.

Service note · FR 108

FR 108: engine, fuel and starter specifications

34.4 cc /37 x 32 mm; 3.5 x 800 mm starter rope, seven spring turns and minimum half-turn spare travel.

  • Powerhead: displacement 34.4 cm³ (2.1 cu.in), bore 37 mm (1.46 in), stroke 32 mm (1.26 in), engine power to ISO 8893 1.1 kW (1.5 bhp). Weight 10.3 kg (22.7 lb) EXCLUDES cutting tool and deflector.
  • Printed full-load engine speed WITHOUT CUTTING TOOL 12,000 rpm; output shaft maximum 9,000 rpm; clutch engagement 3,500 rpm; idle 2,800 rpm. These are distinct historical specifications, not authorization to run an unattended machine.
  • Single-pawl rewind starter: spring tension 7 turns of rope rotor, spare travel MINIMUM 1/2 turn. Starter rope diameter 3.5 mm (0.14 in), length 800 mm (31.5 in). Retained FR 108 sheet B agrees on 3.5 x 800 mm; bulk-rope roll length is not installed-rope length.
  • Fuel system uses foam and felt filter elements; fuel capacity 0.69 l (1.45 US pt). No fuel/oil mixture ratio is supplied on these specification pages. Approved cutting tools are those in section 2, not inferred from engine power.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 4 · TI 4/1995, p. 5 — engine, fuel and starter specifications.

No additional parts-table entry added.

Service note · FR 108

FR 108: engine fastener torque table

Fastener size AND component determine torque; two tensioner rows are unspecified, not zero.

  • Table values below retain the printed Nm / lbf.ft pair, not recalculated conversions. Size alone does not select the torque: IS-M 5x16 has several component-specific values. Spline screws unless otherwise named.
  • Crankcase, IS-M 5x30: 10.5 / 7.7. Cylinder to crankcase, IS-M 5x16: 10.0 / 7.4. Clutch shoes, hex-head M8x20: 17.0 / 12.5. Muffler to cylinder, IS-M 5x16: 10.5 / 7.7. Muffler to crankcase, IS-M 5x12: 10.5 / 7.7. Cover plate to muffler, IS-M 4x12: 3.5 / 2.6.
  • Clutch housing, IS-M 5x16: 9.5 / 7.0. Support to clutch housing, IS-M 5x16: 7.5 / 5.5. Fuel tank, flange screw IS-M 5x14: 5.5 / 4.0. Flywheel, hexagon nut M8: 17.0 / 12.5. Carrier, hexagon nut M8: 17.0 / 12.5.
  • Starter cover TOP, IS-M 5x16: 5.5 / 4.0. Support/starter cover BOTTOM, IS-M 5x16: 7.5 / 5.5. Rope rotor, special spline IS-P 5.5x12: 2.5 / 1.8. Ignition module, IS-M 5x20: 7.5 / 5.5. Spark plug, M14x1.25: 19.0 / 14.0.
  • Carburetor, IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder, IS-M 5x25: 5.5 / 4.0. Adjusting screw in tensioner, IS-M 4x25: DASH. Tensioner to spacer flange, IS-M 5x16: DASH. Both dashes mean no torque specified in this table, NOT zero and not permission to substitute an all-others value. The source labels these tensioner rows even though this is a brushcutter; preserve the wording without inventing a component identity or correction.
  • No tightening sequence, reuse criteria, lubrication or thread-locking rule is supplied by this table. Use the applicable service procedure for the actual configuration.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 8 — engine fastener torque table.

No additional parts-table entry added.

Service note · FR 108

FR 108: workshop-tool roster and three explicit alternatives

Flange, air-gap gauge and circlip-plier alternatives stay conditional; signal-equipped wrenches are distinct.

  • 1113 850 4200 — Test flange: leakage test; 1128 850 4200 — Alternative test flange: footnote 1 alternative to 1113 850 4200; 1111 890 6400 — Setting gauge: ignition module/flywheel air gap; 4118 890 6401 — Alternative setting gauge: footnote 2 alternative to 1111 890 6400; 0000 890 4400 — Puller: removing oil seals; 0000 893 3706 — Jaws profile 3.1: for oil-seal puller; 5910 890 2210 — Installing tool 10: hookless piston snap rings; 5910 893 5608 — Socket 13 mm: crankshaft nut: carrier/flywheel; 5910 890 0301 — Torque wrench: 0.5 to 18 Nm; 5910 890 0302 — Torque wrench: 0.5 to 18 Nm; optical/acoustical signal; 5910 890 0311 — Torque wrench: 6 to 80 Nm; 5910 890 0312 — Torque wrench: 6 to 80 Nm; optical/acoustical signal; 5910 893 8800 — Assembly hook: removing pickup body; 5910 890 2400 — T-handle screwdriver QI-T27x150: IS spline screws; 5910 890 8210 — Crimping tool: wire connectors and lugs; 5910 850 3100 — Assembly stand: holds powerhead for repair; 5910 893 2500 — Flange: assembly stand accessory; 5910 890 2100 — Clamping plate: settings as for FS 106 or FS 108; 0812 542 2104 — Socket: cylinder base screws; 4119 893 7200 — Press arbor: removing/installing main bearings; 0811 641 8380 — Pliers C19: INTERNAL gearhead circlips; 0816 630 1452 — C8 pliers: footnote 5 alternative to C19 pliers; 0811 611 8200 — Pliers A10: EXTERNAL circlips: clutch drum, gearhead, drive pinion; 0816 610 1495 — Circlip pliers: EXTERNAL clutch-drum circlips; 1108 893 4700 — Press arbor: removing clutch drum; 1118 893 7200 — Press arbor: removing/installing ball bearing in clutch housing.
  • Footnotes permit ONLY the stated alternatives: flange 1128 850 4200 for 1113 850 4200; gauge 4118 890 6401 for 1111 890 6400; C8 pliers 0816 630 1452 for C19 pliers 0811 641 8380. These are historical tool alternatives, not blanket machine-part interchange.
  • Footnote 4, optical/acoustical signal, attaches to torque wrenches 5910 890 0302 and 5910 890 0312, not all four wrench identifiers. The two ranges are 0.5–18 Nm and 6–80 Nm respectively. Assembly-stand accessory settings are referenced as for FS 106 or FS 108; actual setup dimensions are not provided here.
  • Removing tool 4119 890 4600 is separately documented with its MANDATORY modification drawing; it must not be treated as an unrestricted tool from this roster. Neither roster nor generic tool name supplies a complete repair procedure.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 10 — workshop-tool roster and three explicit alternatives.

Part numbers (26)
  • 1113 850 4200 — Test flangeleakage test · FR 108; TI 04/1995 conditions
  • 1128 850 4200 — Alternative test flangefootnote 1 alternative to 1113 850 4200 · FR 108; TI 04/1995 conditions
  • 1111 890 6400 — Setting gaugeignition module/flywheel air gap · FR 108; TI 04/1995 conditions
  • 4118 890 6401 — Alternative setting gaugefootnote 2 alternative to 1111 890 6400 · FR 108; TI 04/1995 conditions
  • 0000 890 4400 — Pullerremoving oil seals · FR 108; TI 04/1995 conditions
  • 0000 893 3706 — Jaws profile 3.1for oil-seal puller · FR 108; TI 04/1995 conditions
  • 5910 890 2210 — Installing tool 10hookless piston snap rings · FR 108; TI 04/1995 conditions
  • 5910 893 5608 — Socket 13 mmcrankshaft nut: carrier/flywheel · FR 108; TI 04/1995 conditions
  • 5910 890 0301 — Torque wrench0.5 to 18 Nm · FR 108; TI 04/1995 conditions
  • 5910 890 0302 — Torque wrench0.5 to 18 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
  • 5910 890 0311 — Torque wrench6 to 80 Nm · FR 108; TI 04/1995 conditions
  • 5910 890 0312 — Torque wrench6 to 80 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
  • 5910 893 8800 — Assembly hookremoving pickup body · FR 108; TI 04/1995 conditions
  • 5910 890 2400 — T-handle screwdriver QI-T27x150IS spline screws · FR 108; TI 04/1995 conditions
  • 5910 890 8210 — Crimping toolwire connectors and lugs · FR 108; TI 04/1995 conditions
  • 5910 850 3100 — Assembly standholds powerhead for repair · FR 108; TI 04/1995 conditions
  • 5910 893 2500 — Flangeassembly stand accessory · FR 108; TI 04/1995 conditions
  • 5910 890 2100 — Clamping platesettings as for FS 106 or FS 108 · FR 108; TI 04/1995 conditions
  • 0812 542 2104 — Socketcylinder base screws · FR 108; TI 04/1995 conditions
  • 4119 893 7200 — Press arborremoving/installing main bearings · FR 108; TI 04/1995 conditions
  • 0811 641 8380 — Pliers C19INTERNAL gearhead circlips · FR 108; TI 04/1995 conditions
  • 0816 630 1452 — C8 pliersfootnote 5 alternative to C19 pliers · FR 108; TI 04/1995 conditions
  • 0811 611 8200 — Pliers A10EXTERNAL circlips: clutch drum, gearhead, drive pinion · FR 108; TI 04/1995 conditions
  • 0816 610 1495 — Circlip pliersEXTERNAL clutch-drum circlips · FR 108; TI 04/1995 conditions
  • 1108 893 4700 — Press arborremoving clutch drum · FR 108; TI 04/1995 conditions
  • 1118 893 7200 — Press arborremoving/installing ball bearing in clutch housing · FR 108; TI 04/1995 conditions

Wrong number or missing part for the FR 108? Report a correction →