← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section C · 3 of 15 · 18 parts

Ignition system, Clutch

Fits FR 108.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131414151623456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (18)

PosPart numberDescriptionQty
1 4129 400 1200 Flywheel Fitment / change note → 1
2 9291 021 0180 Washer 8.4 1
3 9210 260 1100 Hexagon nut M8 1
4 4135 400 1300 Ignition module Fitment / change note → 1
5 not sold separately Ignition lead 175 mm not available as a separate item 1
6 0000 989 1010 Grommet 1
7 9022 341 1019 Spline screw IS-M5x20 2
8 4135 160 2001 Clutch 1
9 4117 162 8900 Washer 2
10 4129 162 8900 Washer 2
11 4135 162 4200 Collar screw 2
12 0000 997 6100 Tension spring 1
13 4129 997 1200 Tension spring 1
14 4117 162 8900 Washer 4
15 0000 961 0803 Ring 2
16 9008 319 1800 Hexagon head screw M8x20 2
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m not illustratedoption 1
— 0000 930 2251 Ignition lead 10 m not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 108 / FR 108

FS 108 / FR 108: series 4135 replacement ignition assignment

4135 400 1300 with flywheel 4129 400 1200; 175 mm ignition lead.

  • Printed series 4135. Use 4135 400 1300 with flywheel 4129 400 1200.
  • Printed ignition-lead length: 175 mm (6 7/8 in). Preserve both printed units.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4135 400 1300 — Replacement ignition moduleAssigned component · FS 108 / FR 108, printed series 4135, listed combination only
  • 4129 400 1200 — Assigned flywheelRequired pairing · FS 108 / FR 108, printed series 4135

Service note · FR 108

FR 108: ignition settings and lead-length difference

0.1–0.5 mm air gap, timing at 8,000 rpm; TI lead 220 mm differs from retained IPL 175 mm.

  • Electronic ignition consists of flywheel and module with integral trigger unit. Flywheel need not be removed for access to the ignition module; this is not a complete removal procedure.
  • Air gap 0.1–0.5 mm (0.004–0.020 in). Ignition timing 1.45–2.05 mm (0.06–0.08 in) B.T.D.C. at 8,000 rpm. These millimetres before top dead centre are NOT crankshaft degrees.
  • Suppressed spark plug: Bosch WSR 6 F OR NGK BPMR 7 A; printed heat range 200; electrode gap 0.5 mm (0.020 in); M 14 x 1.25 thread, length 9.5 mm (0.37 in). The TI does not supply plug order numbers.
  • Printed ignition lead length 220 mm (8¾ in) differs from retained 2012 FR 108 ignition sheet C item 5, lead 175 mm. Preserve this unresolved edition/configuration difference; do not silently replace either value or infer a cutting instruction.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 3 · TI 4/1995, p. 5 — ignition settings and lead-length difference.

No additional parts-table entry added.

Service note · FR 108

FR 108: engine fastener torque table

Fastener size AND component determine torque; two tensioner rows are unspecified, not zero.

  • Table values below retain the printed Nm / lbf.ft pair, not recalculated conversions. Size alone does not select the torque: IS-M 5x16 has several component-specific values. Spline screws unless otherwise named.
  • Crankcase, IS-M 5x30: 10.5 / 7.7. Cylinder to crankcase, IS-M 5x16: 10.0 / 7.4. Clutch shoes, hex-head M8x20: 17.0 / 12.5. Muffler to cylinder, IS-M 5x16: 10.5 / 7.7. Muffler to crankcase, IS-M 5x12: 10.5 / 7.7. Cover plate to muffler, IS-M 4x12: 3.5 / 2.6.
  • Clutch housing, IS-M 5x16: 9.5 / 7.0. Support to clutch housing, IS-M 5x16: 7.5 / 5.5. Fuel tank, flange screw IS-M 5x14: 5.5 / 4.0. Flywheel, hexagon nut M8: 17.0 / 12.5. Carrier, hexagon nut M8: 17.0 / 12.5.
  • Starter cover TOP, IS-M 5x16: 5.5 / 4.0. Support/starter cover BOTTOM, IS-M 5x16: 7.5 / 5.5. Rope rotor, special spline IS-P 5.5x12: 2.5 / 1.8. Ignition module, IS-M 5x20: 7.5 / 5.5. Spark plug, M14x1.25: 19.0 / 14.0.
  • Carburetor, IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder, IS-M 5x25: 5.5 / 4.0. Adjusting screw in tensioner, IS-M 4x25: DASH. Tensioner to spacer flange, IS-M 5x16: DASH. Both dashes mean no torque specified in this table, NOT zero and not permission to substitute an all-others value. The source labels these tensioner rows even though this is a brushcutter; preserve the wording without inventing a component identity or correction.
  • No tightening sequence, reuse criteria, lubrication or thread-locking rule is supplied by this table. Use the applicable service procedure for the actual configuration.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 8 — engine fastener torque table.

No additional parts-table entry added.

Service note · FR 108

FR 108: workshop-tool roster and three explicit alternatives

Flange, air-gap gauge and circlip-plier alternatives stay conditional; signal-equipped wrenches are distinct.

  • 1113 850 4200 — Test flange: leakage test; 1128 850 4200 — Alternative test flange: footnote 1 alternative to 1113 850 4200; 1111 890 6400 — Setting gauge: ignition module/flywheel air gap; 4118 890 6401 — Alternative setting gauge: footnote 2 alternative to 1111 890 6400; 0000 890 4400 — Puller: removing oil seals; 0000 893 3706 — Jaws profile 3.1: for oil-seal puller; 5910 890 2210 — Installing tool 10: hookless piston snap rings; 5910 893 5608 — Socket 13 mm: crankshaft nut: carrier/flywheel; 5910 890 0301 — Torque wrench: 0.5 to 18 Nm; 5910 890 0302 — Torque wrench: 0.5 to 18 Nm; optical/acoustical signal; 5910 890 0311 — Torque wrench: 6 to 80 Nm; 5910 890 0312 — Torque wrench: 6 to 80 Nm; optical/acoustical signal; 5910 893 8800 — Assembly hook: removing pickup body; 5910 890 2400 — T-handle screwdriver QI-T27x150: IS spline screws; 5910 890 8210 — Crimping tool: wire connectors and lugs; 5910 850 3100 — Assembly stand: holds powerhead for repair; 5910 893 2500 — Flange: assembly stand accessory; 5910 890 2100 — Clamping plate: settings as for FS 106 or FS 108; 0812 542 2104 — Socket: cylinder base screws; 4119 893 7200 — Press arbor: removing/installing main bearings; 0811 641 8380 — Pliers C19: INTERNAL gearhead circlips; 0816 630 1452 — C8 pliers: footnote 5 alternative to C19 pliers; 0811 611 8200 — Pliers A10: EXTERNAL circlips: clutch drum, gearhead, drive pinion; 0816 610 1495 — Circlip pliers: EXTERNAL clutch-drum circlips; 1108 893 4700 — Press arbor: removing clutch drum; 1118 893 7200 — Press arbor: removing/installing ball bearing in clutch housing.
  • Footnotes permit ONLY the stated alternatives: flange 1128 850 4200 for 1113 850 4200; gauge 4118 890 6401 for 1111 890 6400; C8 pliers 0816 630 1452 for C19 pliers 0811 641 8380. These are historical tool alternatives, not blanket machine-part interchange.
  • Footnote 4, optical/acoustical signal, attaches to torque wrenches 5910 890 0302 and 5910 890 0312, not all four wrench identifiers. The two ranges are 0.5–18 Nm and 6–80 Nm respectively. Assembly-stand accessory settings are referenced as for FS 106 or FS 108; actual setup dimensions are not provided here.
  • Removing tool 4119 890 4600 is separately documented with its MANDATORY modification drawing; it must not be treated as an unrestricted tool from this roster. Neither roster nor generic tool name supplies a complete repair procedure.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 10 — workshop-tool roster and three explicit alternatives.

Part numbers (26)
  • 1113 850 4200 — Test flangeleakage test · FR 108; TI 04/1995 conditions
  • 1128 850 4200 — Alternative test flangefootnote 1 alternative to 1113 850 4200 · FR 108; TI 04/1995 conditions
  • 1111 890 6400 — Setting gaugeignition module/flywheel air gap · FR 108; TI 04/1995 conditions
  • 4118 890 6401 — Alternative setting gaugefootnote 2 alternative to 1111 890 6400 · FR 108; TI 04/1995 conditions
  • 0000 890 4400 — Pullerremoving oil seals · FR 108; TI 04/1995 conditions
  • 0000 893 3706 — Jaws profile 3.1for oil-seal puller · FR 108; TI 04/1995 conditions
  • 5910 890 2210 — Installing tool 10hookless piston snap rings · FR 108; TI 04/1995 conditions
  • 5910 893 5608 — Socket 13 mmcrankshaft nut: carrier/flywheel · FR 108; TI 04/1995 conditions
  • 5910 890 0301 — Torque wrench0.5 to 18 Nm · FR 108; TI 04/1995 conditions
  • 5910 890 0302 — Torque wrench0.5 to 18 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
  • 5910 890 0311 — Torque wrench6 to 80 Nm · FR 108; TI 04/1995 conditions
  • 5910 890 0312 — Torque wrench6 to 80 Nm; optical/acoustical signal · FR 108; TI 04/1995 conditions
  • 5910 893 8800 — Assembly hookremoving pickup body · FR 108; TI 04/1995 conditions
  • 5910 890 2400 — T-handle screwdriver QI-T27x150IS spline screws · FR 108; TI 04/1995 conditions
  • 5910 890 8210 — Crimping toolwire connectors and lugs · FR 108; TI 04/1995 conditions
  • 5910 850 3100 — Assembly standholds powerhead for repair · FR 108; TI 04/1995 conditions
  • 5910 893 2500 — Flangeassembly stand accessory · FR 108; TI 04/1995 conditions
  • 5910 890 2100 — Clamping platesettings as for FS 106 or FS 108 · FR 108; TI 04/1995 conditions
  • 0812 542 2104 — Socketcylinder base screws · FR 108; TI 04/1995 conditions
  • 4119 893 7200 — Press arborremoving/installing main bearings · FR 108; TI 04/1995 conditions
  • 0811 641 8380 — Pliers C19INTERNAL gearhead circlips · FR 108; TI 04/1995 conditions
  • 0816 630 1452 — C8 pliersfootnote 5 alternative to C19 pliers · FR 108; TI 04/1995 conditions
  • 0811 611 8200 — Pliers A10EXTERNAL circlips: clutch drum, gearhead, drive pinion · FR 108; TI 04/1995 conditions
  • 0816 610 1495 — Circlip pliersEXTERNAL clutch-drum circlips · FR 108; TI 04/1995 conditions
  • 1108 893 4700 — Press arborremoving clutch drum · FR 108; TI 04/1995 conditions
  • 1118 893 7200 — Press arborremoving/installing ball bearing in clutch housing · FR 108; TI 04/1995 conditions

Wrong number or missing part for the FR 108? Report a correction →