← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section D · 4 of 15 · 14 parts

Cover, Fuel tank

Fits FR 108.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (14)

PosPart numberDescriptionQty
1 4135 080 1600 Shroud Fitment / change note → 1
2 9416 868 6510 Hollow rivet 6.5x0.5x3.0 2
3 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
4 4135 967 1506 Model plate FR 108 1
5 4135 350 0400 Fuel tank 1
6 4112 358 8100 Insert 4
7 4128 350 0505 Filler cap 1
8 0000 350 0900 Rope 1
9 0000 353 0800 Filler cap retainer 1
10 0000 350 3502 Pickup body 1
11 0000 358 1800 Filter 1
12 4126 358 7700 Hose with grommet 1
13 9307 021 0120 Washer 5.3 4
14 9022 341 0980 Spline screw IS-M5x16 4

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 108

FR 108: engine, fuel and starter specifications

34.4 cc /37 x 32 mm; 3.5 x 800 mm starter rope, seven spring turns and minimum half-turn spare travel.

  • Powerhead: displacement 34.4 cm³ (2.1 cu.in), bore 37 mm (1.46 in), stroke 32 mm (1.26 in), engine power to ISO 8893 1.1 kW (1.5 bhp). Weight 10.3 kg (22.7 lb) EXCLUDES cutting tool and deflector.
  • Printed full-load engine speed WITHOUT CUTTING TOOL 12,000 rpm; output shaft maximum 9,000 rpm; clutch engagement 3,500 rpm; idle 2,800 rpm. These are distinct historical specifications, not authorization to run an unattended machine.
  • Single-pawl rewind starter: spring tension 7 turns of rope rotor, spare travel MINIMUM 1/2 turn. Starter rope diameter 3.5 mm (0.14 in), length 800 mm (31.5 in). Retained FR 108 sheet B agrees on 3.5 x 800 mm; bulk-rope roll length is not installed-rope length.
  • Fuel system uses foam and felt filter elements; fuel capacity 0.69 l (1.45 US pt). No fuel/oil mixture ratio is supplied on these specification pages. Approved cutting tools are those in section 2, not inferred from engine power.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 4 · TI 4/1995, p. 5 — engine, fuel and starter specifications.

No additional parts-table entry added.

Service note · FR 108

FR 108: engine fastener torque table

Fastener size AND component determine torque; two tensioner rows are unspecified, not zero.

  • Table values below retain the printed Nm / lbf.ft pair, not recalculated conversions. Size alone does not select the torque: IS-M 5x16 has several component-specific values. Spline screws unless otherwise named.
  • Crankcase, IS-M 5x30: 10.5 / 7.7. Cylinder to crankcase, IS-M 5x16: 10.0 / 7.4. Clutch shoes, hex-head M8x20: 17.0 / 12.5. Muffler to cylinder, IS-M 5x16: 10.5 / 7.7. Muffler to crankcase, IS-M 5x12: 10.5 / 7.7. Cover plate to muffler, IS-M 4x12: 3.5 / 2.6.
  • Clutch housing, IS-M 5x16: 9.5 / 7.0. Support to clutch housing, IS-M 5x16: 7.5 / 5.5. Fuel tank, flange screw IS-M 5x14: 5.5 / 4.0. Flywheel, hexagon nut M8: 17.0 / 12.5. Carrier, hexagon nut M8: 17.0 / 12.5.
  • Starter cover TOP, IS-M 5x16: 5.5 / 4.0. Support/starter cover BOTTOM, IS-M 5x16: 7.5 / 5.5. Rope rotor, special spline IS-P 5.5x12: 2.5 / 1.8. Ignition module, IS-M 5x20: 7.5 / 5.5. Spark plug, M14x1.25: 19.0 / 14.0.
  • Carburetor, IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder, IS-M 5x25: 5.5 / 4.0. Adjusting screw in tensioner, IS-M 4x25: DASH. Tensioner to spacer flange, IS-M 5x16: DASH. Both dashes mean no torque specified in this table, NOT zero and not permission to substitute an all-others value. The source labels these tensioner rows even though this is a brushcutter; preserve the wording without inventing a component identity or correction.
  • No tightening sequence, reuse criteria, lubrication or thread-locking rule is supplied by this table. Use the applicable service procedure for the actual configuration.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 8 — engine fastener torque table.

No additional parts-table entry added.

Service note · FS 108 / FR 108

FS/FR108 shroud: same number, emissions symbol restriction

Only shrouds without the open-one-turn symbol may be used on emissions-approved machines.

  • Emissions-approved H/L user adjustment is limited to maximum 90 degrees. Therefore the OPEN 1 TURN symbol is omitted from their shrouds. Figure 354TI012 crosses out that setting symbol; it does not delete H, L or LD identification. ONLY SHROUDS WITHOUT THE SETTING SYMBOL MAY BE USED on emissions-approved machines.
  • To standardize parts the TI says the setting symbol will be omitted on all future machines/shrouds in this FS108/FR108 context; it does not establish all-model fitment. Both original and modified table columns use THE SAME NUMBER 4135 080 1600. Number alone does not identify symbol state.
  • Introduction: emissions machines FROM START OF PRODUCTION; non-emissions machines IN PROGRESS. Unmodified parts will be supplied until existing factory stocks are exhausted. That old-stock statement DOES NOT override the emissions-only no-symbol restriction. No serial cutoff or production date is provided.
  • Later exact-model cover/fuel-tank IPLs retain shroud 4135 080 1600 at key 1 without encoding symbol state. Last TI references FS108 37.94 and FR108 05.95 are bibliographic. Footer June 09, 1995, Andreas Stihl D1/MTK-na, Technical Documentation; issue 15.95 is not a production date.
  • Historical TI guidance only, specific to FS 108 / FR 108 and the stated carburetor version. Exact-model IPL links are navigation, not unrestricted interchange. No hardware operation was performed.

Source: TI 15/1995, p. 10 · TI 15/1995, p. 11 — Complete bulletin: emissions carburetor and shroud; all text, figures, flowchart, tables and footer.

Part numbers (1)
  • 4135 080 1600 — Shroudsame number before/after symbol deletion; inspect version · FS 108; FR 108

Wrong number or missing part for the FR 108? Report a correction →