Stihl 4135 · Section E · 5 of 15 · 19 parts
Air filter
Fits FR 108.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (19)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4135 141 0800 | Filter housing | 1 |
| 2 | 9022 341 1220 | Spline screw IS-M5x48 | 2 |
| 3 | 4135 124 2800 | Filter | 1 |
| 4 | 4135 124 1500 | Prefilter | 1 |
| 5 | 4135 141 0500 | Filter cover | 1 |
| 6 | 4135 149 0500 | Gasket | 1 |
| 7 | 4135 120 0602 | Carburetor SK5 | 1 |
| 8 | 4135 120 0601 NLA | Carburetor C1Q-SK7 | 1 |
| 9 | 4222 123 7300 | Lever | 1 |
| 10 | 4135 129 0905 | Gasket | 1 |
| 11 | 9022 341 0980 | Spline screw IS-M5x16 | 1 |
| 12 | 4135 182 7600 | Tensioner | 1 |
| 13 | 9022 313 0680 | Spline screw IS-M4x16 | 1 |
| 14 | 9022 341 1050 | Spline screw IS-M5x25 | 2 |
| 15 | 9291 021 0120 | Washer 5.3 | 2 |
| 16 | 4135 121 1600 | Spacer flange | 1 |
| 17 | 9214 320 0700 | Lock nut M5 | 1 |
| 18 | 4135 129 0900 | Gasket | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4135 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FR 108
FR 108: two-stroke construction and two-stage filter
Die-cast crankcase, two-ring piston and foam/felt filter; FR 106 design ancestry is not blanket parts interchange.
- Professional backpack brushcutter based on the FR 106 design concept; source claims the same 1.1 kW (1.5 bhp), increased torque and easier servicing, and approximately 0.5 kg (1.1 lb) less weight. These comparisons have not been independently tested. Photograph 360 TI 001 shows a configuration, not a complete supplied-parts inventory.
- Compact two-stroke powerhead has smooth exterior surfaces to reduce dirt accumulation and aid cleaning; housing helps prevent contact with hot engine parts. Crankcase is a two-part aluminum die casting with two dust-lip oil seals. Crankshaft is a three-part assembly pressed together before final machining.
- Aluminum-alloy piston has TWO compression rings; piston pin runs in a needle cage and is retained by hookless wire snap rings. Special aluminum-alloy cylinder has an electroplated wear-resistant bore; the coating composition is not specified.
- Diaphragm carburetor mounts to the cylinder with thermal insulation. Air filter illustration 357 TI 004: flat foam element (1), felt element (2), tool-free removable/refittable cover (3). Large-volume muffler has a fire screen. These diagram keys are not current IPL drawing positions.
- Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 1 · TI 4/1995, p. 2 · TI 4/1995, p. 3 — two-stroke construction and two-stage filter.
No additional parts-table entry added.
Service note · FR 108
FR 108: carburetor basic settings and separate leak tests
H/L one turn; carb closing pressure 0.8 bar versus crankcase pressure/vacuum 0.5 bar; not a complete repair procedure.
- Historical basic setting: high-speed H and low-speed L screws each back off ONE full turn. Source wording says initially “hard against their seats”; preserve it as a dated quotation, not a new instruction to force or damage an adjustment seat. Verify the actual carburetor and applicable service procedure; the TI supplies no carburetor model designation or limiter-cap instructions here.
- Full-load engine speed WITHOUT CUTTING TOOL 12,000 rpm; idle 2,800 rpm. Carburetor leakage-test closing pressure 0.8 bar (11.6 psi). Crankcase leakage test: gauge pressure 0.5 bar (7.25 psi), vacuum 0.5 bar (7.25 psi). Vacuum is a magnitude, not a positive-pressure test. No hold time or allowed leakage rate is supplied here.
- Page 11 requires the FR 108 service manual for service/repair and all local/national safety rules plus owner-manual precautions if started during repair. It says carburetor servicing, troubleshooting and other standard repairs are omitted from the new manual and planned for a separate handbook; appropriate FR/FS 106 manual chapters are the stated interim reference. This note does not supply or verify those missing procedures, and the complete TI/manual-dependency disposition is now recorded in the accompanying repair-manual boundaries note; exact missing procedures remain source gaps.
- Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 7 · TI 4/1995, p. 11 — carburetor basic settings and separate leak tests.
No additional parts-table entry added.
Service note · FR 108
FR 108: engine fastener torque table
Fastener size AND component determine torque; two tensioner rows are unspecified, not zero.
- Table values below retain the printed Nm / lbf.ft pair, not recalculated conversions. Size alone does not select the torque: IS-M 5x16 has several component-specific values. Spline screws unless otherwise named.
- Crankcase, IS-M 5x30: 10.5 / 7.7. Cylinder to crankcase, IS-M 5x16: 10.0 / 7.4. Clutch shoes, hex-head M8x20: 17.0 / 12.5. Muffler to cylinder, IS-M 5x16: 10.5 / 7.7. Muffler to crankcase, IS-M 5x12: 10.5 / 7.7. Cover plate to muffler, IS-M 4x12: 3.5 / 2.6.
- Clutch housing, IS-M 5x16: 9.5 / 7.0. Support to clutch housing, IS-M 5x16: 7.5 / 5.5. Fuel tank, flange screw IS-M 5x14: 5.5 / 4.0. Flywheel, hexagon nut M8: 17.0 / 12.5. Carrier, hexagon nut M8: 17.0 / 12.5.
- Starter cover TOP, IS-M 5x16: 5.5 / 4.0. Support/starter cover BOTTOM, IS-M 5x16: 7.5 / 5.5. Rope rotor, special spline IS-P 5.5x12: 2.5 / 1.8. Ignition module, IS-M 5x20: 7.5 / 5.5. Spark plug, M14x1.25: 19.0 / 14.0.
- Carburetor, IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder, IS-M 5x25: 5.5 / 4.0. Adjusting screw in tensioner, IS-M 4x25: DASH. Tensioner to spacer flange, IS-M 5x16: DASH. Both dashes mean no torque specified in this table, NOT zero and not permission to substitute an all-others value. The source labels these tensioner rows even though this is a brushcutter; preserve the wording without inventing a component identity or correction.
- No tightening sequence, reuse criteria, lubrication or thread-locking rule is supplied by this table. Use the applicable service procedure for the actual configuration.
- Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 8 — engine fastener torque table.
No additional parts-table entry added.
Service note · FR 108
FR 108: piston, seal and leakage-test tools
Starter-side seal protection and installation use different sleeves; leak-test equipment is not a test procedure.
- 4112 893 1200 — Piston locking screw: blocking crankshaft; 1129 893 2400 — Press sleeve: installing clutch-side oil seal; 4112 893 2400 — Press sleeve: PROTECTING starter-side oil seal; 1115 893 4600 — Press sleeve: INSTALLING starter-side oil seal; 4117 893 4700 — Press arbor: installing piston pin; 0000 893 2600 — Clamping strap: compressing piston rings; 1108 893 4800 — Wooden assembly block: fitting piston; 1106 850 2905 — Crankcase and carburetor tester: testing crankcase and carburetor for leaks; 0000 855 9200 — Nipple: carburetor leakage test; 1110 141 8600 — Fuel line: carburetor leakage test; 0000 850 3501 — Vacuum pump: crankcase leakage test; 0000 855 8106 — Sealing plate: sealing exhaust port for leakage test.
- The nipple and fuel line are subordinate tester accessories in the source table, not a machine fuel-line fitment declaration. PROTECTING the starter-side seal with 4112 893 2400 is distinct from INSTALLING it with 1115 893 4600. No removal/assembly sequence, fixture setup or leak-test hold time is supplied in this roster.
- Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 9 — piston, seal and leakage-test tools.
Part numbers (12)
- 4112 893 1200 — Piston locking screwblocking crankshaft · FR 108; TI 04/1995 conditions
- 1129 893 2400 — Press sleeveinstalling clutch-side oil seal · FR 108; TI 04/1995 conditions
- 4112 893 2400 — Press sleevePROTECTING starter-side oil seal · FR 108; TI 04/1995 conditions
- 1115 893 4600 — Press sleeveINSTALLING starter-side oil seal · FR 108; TI 04/1995 conditions
- 4117 893 4700 — Press arborinstalling piston pin · FR 108; TI 04/1995 conditions
- 0000 893 2600 — Clamping strapcompressing piston rings · FR 108; TI 04/1995 conditions
- 1108 893 4800 — Wooden assembly blockfitting piston · FR 108; TI 04/1995 conditions
- 1106 850 2905 — Crankcase and carburetor testertesting crankcase and carburetor for leaks · FR 108; TI 04/1995 conditions
- 0000 855 9200 — Nipplecarburetor leakage test · FR 108; TI 04/1995 conditions
- 1110 141 8600 — Fuel linecarburetor leakage test · FR 108; TI 04/1995 conditions
- 0000 850 3501 — Vacuum pumpcrankcase leakage test · FR 108; TI 04/1995 conditions
- 0000 855 8106 — Sealing platesealing exhaust port for leakage test · FR 108; TI 04/1995 conditions
Service note · FR 108
FR 108: repair-manual boundaries and operating precautions
The new manual omits carburetor servicing, troubleshooting and standard repairs; FR/FS106 chapters are the historical interim reference.
- If started during repairs or maintenance, the unit requires strict observance of ALL local and national safety regulations AND the owner-manual safety precautions. This source statement is retained; it is not permission for unattended startup or a replacement for the actual owner manual.
- For FR 108 servicing and repair, section 8 refers to its service manual. The new manual omits “Servicing the Carburetor”, “Troubleshooting” and other standard repair jobs. A separate handbook is described as forthcoming in 1995; appropriate chapters of the FR and FS 106 service manual are the stated INTERIM reference until that handbook is published.
- Local dependency review searched the retained STIHL service documentation manual catalog and first-three-page PDF covers, including separately organized service manuals and RA/HB resources. The exact FS 88/108/FR 108 shop manual and FR/FS 106 interim manual were not identified. No edition of the unnamed forthcoming handbook is established by this TI; similarly titled later material is not automatically that edition. These are scoped source gaps, not proof that the documents never existed.
- The available TI dimensions, torque and repair-time tables do not replace the missing procedures. Whole-manual review/import is a separate follow-on phase; none of these manuals is claimed imported or accepted here. Footer identifies Waiblingen, 22.02.1995; ©1995 Andreas Stihl; Technical Documentation, D1/MTK-na. Publication date is not a serial changeover.
- Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.
Source: TI 4/1995, p. 9 · TI 4/1995, p. 11 — repair-manual boundaries and operating precautions.
No additional parts-table entry added.
Wrong number or missing part for the FR 108? Report a correction →