← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section L · 11 of 15 · 30 parts

Control handle

Fits FR 108.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314141516171819220212223242526273456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (30)

PosPart numberDescriptionQty
1 4126 791 0821 Handle molding, outer 1
2 4126 182 4506 Torsion spring 1
3 4126 182 0806 Lockout lever 1
4 4126 182 6210 Collar screw 1
5 4126 790 1102 Handle molding, inner 1
6 4126 791 5300 Connector tag 2
7 4126 182 1705 Slide control 1
8 4126 182 4705 Detent spring 1
9 4126 182 6205 Collar screw 1
10 4126 182 4505 Torsion spring 1
11 9417 003 7510 Push nut 1
12 4126 182 1007 Throttle trigger 1
13 4126 791 9400 Hose clamp 2
14 4126 792 6100 Square washer 4
15 9022 341 0980 Spline screw IS-M5x16 2
16 9074 478 3065 Pan head self-tapping screw IS-P4x19 4
17 4126 182 4507 Torsion spring 1
18 4135 180 1120 Throttle cable 1
19 not sold separately Lead 1330 mm / 52.4'' not available as a separate item 1
20 not sold separately Lead 1400 mm / 55.1'' not available as a separate item 1
21 0751 030 8953 NLA Terminal socket 4.8-1 no longer available from factory 2
22 0751 030 8470 Grommet no longer available from factory 2
23 0751 030 8474 Terminal socket 4.8-1 no longer available from factory 2
24 0751 030 8460 Grommet no longer available from factory 2
25 not sold separately Hose 1030 mm / 4 1/16'' not available as a separate item 1
26 4132 791 4300 Guard 1
27 9074 478 3375 Pan head self-tapping screw IS-P4x35 2
Not numbered on the diagram — assemblies, kits and options
— 4133 790 1301 Control handle 1
— 0751 010 1110 Lead 10 m / 33' not illustratedoption 1
— 4132 711 7200 Hose 1290 mm / 50 13/16'' not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 108

FR 108: pivot mounting, controls and drive geometry

Flexible connection and six-bushing rigid drive are distinct; tool mounting is M 10 x 1 left-hand thread.

  • Handle adjusts along the shaft for operating position. Anti-vibration elements lie between engine and support frame; pivot-mounted engine follows drive-tube movements to reduce loads on the flexible drive shaft. Source describes AV system and controls as on FR 106, without establishing all-part interchange.
  • Control illustration 360 TI 002: throttle trigger lock (4), throttle trigger (5), slide control (6). Starting throttle, run and stop positions are selected one-handed. Claimed handling, safety and fatigue benefits are source descriptions, not independently measured results.
  • Clutch has lined shoes pivot-mounted on the flywheel. Rigid drive shaft is supported by SIX bushings; do not confuse it with the flexible engine connection. Gearhead is described as same as FS 66 through 108 and FR 106, but the TI supplies no universal parts substitution roster for that range.
  • Cutting-tool mounting (page 4 key 7) is M 10 x 1 LEFT-HAND thread, described as on FS 74,76,86,88,106,108 and FR 106. Gearhead is a helical bevel drive with printed ratio 1.33. Source lists engine speed 12,000 rpm separately from maximum output-shaft/tool-mounting speed 9,000 rpm; they are not interchangeable limits.
  • Historical TI 04/1995 guidance for the FR 108, series 4135; no serial cutoff is printed. Historical approvals and specifications are not a current compatibility approval or independently measured performance. Exact-model IPL links are navigation, not permission to apply these values to an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 1 · TI 4/1995, p. 3 · TI 4/1995, p. 4 · TI 4/1995, p. 5 — pivot mounting, controls and drive geometry.

No additional parts-table entry added.

Service note · FR 108

FR 108: handle, drive and support-frame torques

Gearhead clamps print 8.0 Nm without an imperial value; M4/M5 defaults do not override specific rows.

  • All pairs are printed Nm / lbf.ft; spline screws unless otherwise named. Shroud, IS-M 5x12: 5.5 / 4.0. Two halves of control handle, IS-P 4x19: 2.0 / 1.5. Guard to handle molding, IS-P 4x35: 2.0 / 1.5. Clamp on control handle, IS-M 5x16: 3.5 / 2.6.
  • Clamp screw in drive-tube sleeve, IS-M 6x25: 7.0 / 5.2. Setscrew in drive-tube sleeve, IS-M 5x10: 3.5 / 2.6. Clamp screws in gearhead, IS-M 5x20: 8.0 Nm; imperial cell is BLANK in the scan, not zero or a printed conversion.
  • Bracket to support frame, IS-M 5x10: 3.5 / 2.6. Clamp to support frame, IS-M 5x10: 3.5 / 2.6. Bearing housing to support frame, IS-M 6x12: 10.0 / 7.4. Shackle to support frame, IS-M 6x12: 7.0 / 5.2. Rubber buffer, hexagon nut M6: 5.0 / 3.7.
  • Engine mounting, hex-head M10x20: 30.0 / 22.0. Clamp for loop handle AND strain relief cord, IS-M 6x12: 6.0 / 4.4. Grease filler opening in gearhead, screw plug IS-M 11x10: 10.0 / 7.4.
  • Screws/nuts M4, ALL OTHERS: 2.5 / 1.8. Screws/nuts M5, ALL OTHERS: 4.5 / 3.3. These residual rows are not universal torque values and do not replace listed component values or the two explicit unspecified tensioner rows. No sequence or complete installation procedure is provided.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 8 — handle, drive and support-frame torques.

No additional parts-table entry added.

Service note · FR 108

FR 108: AV rubber installing tool and manual dependency

4135 893 4900 has 22.5 and 26 mm ends; tool use is referred to the FS88/108 and FR108 shop manual.

  • New installing tool 4135 893 4900 is for AV rubber elements, diameter 22.5 mm (0.88 in) and 26 mm (1.02 in). Drawing 357TI008 key 1 shows the two different end diameters; it is not a complete dimensioned fabrication drawing.
  • The application row explicitly names FR 108 AND FS 108. Footnote 1 refers to the FS 88, 108 and FR 108 shop manual for USE instructions; the manual title does not itself expand this tool application to FS 88. No installation force, direction or full AV replacement procedure appears on this page.
  • The exact cited shop manual was not identified in the inspected local manual catalog and PDF-cover inventory. Tool dimensions are available evidence, not a substitute for missing operating instructions.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 9 · TI 4/1995, p. 11 — AV rubber installing tool and manual dependency.

Part numbers (1)
  • 4135 893 4900 — AV rubber installing tool; 22.5 and 26 mmFR 108 and FS 108; manual required · FR 108; TI 04/1995 conditions

Service note · FR 108

FR 108: repair-manual boundaries and operating precautions

The new manual omits carburetor servicing, troubleshooting and standard repairs; FR/FS106 chapters are the historical interim reference.

  • If started during repairs or maintenance, the unit requires strict observance of ALL local and national safety regulations AND the owner-manual safety precautions. This source statement is retained; it is not permission for unattended startup or a replacement for the actual owner manual.
  • For FR 108 servicing and repair, section 8 refers to its service manual. The new manual omits “Servicing the Carburetor”, “Troubleshooting” and other standard repair jobs. A separate handbook is described as forthcoming in 1995; appropriate chapters of the FR and FS 106 service manual are the stated INTERIM reference until that handbook is published.
  • Local dependency review searched the retained STIHL service documentation manual catalog and first-three-page PDF covers, including separately organized service manuals and RA/HB resources. The exact FS 88/108/FR 108 shop manual and FR/FS 106 interim manual were not identified. No edition of the unnamed forthcoming handbook is established by this TI; similarly titled later material is not automatically that edition. These are scoped source gaps, not proof that the documents never existed.
  • The available TI dimensions, torque and repair-time tables do not replace the missing procedures. Whole-manual review/import is a separate follow-on phase; none of these manuals is claimed imported or accepted here. Footer identifies Waiblingen, 22.02.1995; ©1995 Andreas Stihl; Technical Documentation, D1/MTK-na. Publication date is not a serial changeover.
  • Historical TI 04/1995 guidance for FR 108, series 4135; no serial cutoff is printed. Exact-model IPL links are navigation, not proof of interchange or permission to use these values on an unidentified later configuration. No hardware operation was performed.

Source: TI 4/1995, p. 9 · TI 4/1995, p. 11 — repair-manual boundaries and operating precautions.

No additional parts-table entry added.

Wrong number or missing part for the FR 108? Report a correction →