← FR 125, FR 135, FR 145 · FS 108 · FR 108

Stihl 4135 · Section A · 1 of 14 · 28 parts

Crankcase, Cylinder

Fits FS 108.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151616171819222021222333445677889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4135 020 2600 Crankcase, fan side 1
2 9380 620 2570 Roll pin 5x12 4
3 9503 003 0242 Grooved ball bearing 6201 2
4 9640 003 1195 Oil seal 12x22x5 2
5 4135 020 2800 Crankcase, starter side 1
6 4135 030 0400 Crankshaft 1
7 0000 958 1222 Shim 0.1 mm
8 0000 958 1223 Shim 0.2 mm
9 9022 341 1070 Spline screw IS-M5x30 4
10 4112 036 8600 Woodruff key 1
11 4126 084 2200 Guard 1
12 4135 022 0500 Cylinder Ø 37 mm 1
13 4135 034 0500 Piston Ø 37 mm 1
14 4129 034 3000 Piston ring Ø 37x1.5 mm 2
15 4117 034 1500 Piston pin 10x7x30 1
16 9463 650 1000 Snap ring 10 2
17 9512 003 2340 Needle cage 10x14x13 1
18 4135 029 2300 Cylinder gasket 1
19 9022 341 0980 Spline screw IS-M5x16 4
20 0000 400 7000 Spark plug NGK BPMR7A 1
20 1110 400 7005 Spark plug Bosch WSR 6 F 1
21 0000 998 0606 Torsion spring 1
22 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
23 4135 149 0600 Muffler gasket 1
Not numbered on the diagram — assemblies, kits and options
— 4135 020 1200 Cylinder with piston Ø 37 mm 1
— 4135 030 2000 Piston Ø 37 mm 1
— 0783 830 2000 Tube of sealant Dirko HT red not illustrated 1
— 4135 007 1050 Set of gaskets Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FS 88 / FS 108

FS 88 / 108: engine and speed specifications

Engine, output-shaft and clutch speeds are different quantities.

  • FS 88: displacement 25.4 cm³ (1.55 cu.in), bore 34 mm (1.34 in), stroke 28 mm (1.10 in), power to ISO 8893 0.9 kW (1.2 bhp). FS 108: 34.4 cm³ (2.1 cu.in), bore 37 mm (1.46 in), stroke 32 mm (1.26 in), 1.1 kW (1.5 bhp).
  • Both: source-labelled full-load engine speed WITHOUT CUTTING TOOL 12000 rpm; idle 2800 rpm. Do not silently relabel this contradictory-sounding source phrase as a loaded-tool test. Maximum output-shaft/tool-mounting speed: FS 88 8800 rpm, FS 108 9000 rpm. Clutch engagement: FS 88 3700 rpm, FS 108 3500 rpm. These values are not interchangeable speed limits.
  • Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.

Source: TI 37/1994, p. 1 · TI 37/1994, p. 4 · TI 37/1994, p. 7 — FS 88 / 108: engine and speed specifications.

No additional parts-table entry added.

Service note · FS 88 / FS 108

FS 88 / 108: crankshaft repair limits

Connecting rod and big-end bearing are not replaceable separately.

  • Compact two-stroke engine; smooth housing surfaces reduce dirt accumulation and aid cleaning; housing helps prevent hot-part contact and diverts exhaust gases and heated cooling air away from the operator. Large-volume muffler is described for silencing; no performance measurement is supplied.
  • Crankcase is a two-part aluminium die casting with two dust-lip oil seals. Three-part crankshaft is pressed together before final machining; connecting rod and big-end bearing are NOT REPLACEABLE. Do not turn this construction description into a crankshaft pressing repair procedure.
  • Aluminium-alloy piston has TWO compression rings. Piston pin runs in a needle cage and is secured by TWO HOOKLESS WIRE SNAP RINGS. Special-aluminium-alloy cylinder has an electroplated wear-resistant-alloy bore; no plating composition, bore-repair permission or pin diameter printed.
  • Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.

Source: TI 37/1994, p. 2 · TI 37/1994, p. 3 — FS 88 / 108: crankshaft repair limits.

No additional parts-table entry added.

Service note · FS 88 / FS 108

FS 88 / 108: model-specific repair kits

Carburetor kits and engine gasket sets retain their separate model rosters.

  • Carburetor parts kit: FS 86 / FS 88 4117 007 1061; FS 106 / FS 108 4132 007 1061. This does NOT approve either kit for every later carburetor appearing on the shared model catalog. No carburetor model code is printed in this table.
  • Gasket set: FS 88 4126 007 1051; FS 108 4135 007 1050. Gasket panel DIN A3 0457 281 2104 is separately listed, not a substitute complete gasket set.
  • Dirko sealant 0783 830 2120 is for sealing the crankcase. Lube grease 0781 120 1111, 370 g (13 oz) tube, is for oil seals; package mass is not an installation quantity. No sealant bead dimension or kit contents supplied.
  • Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.

Source: TI 37/1994, p. 7 — FS 88 / 108: model-specific repair kits.

Part numbers (7)
  • 4117 007 1061 — Carburetor parts kit FS 86 / FS 88historical listed item · FS 88 / 108: model-specific repair kits
  • 4132 007 1061 — Carburetor parts kit FS 106 / FS 108historical listed item · FS 88 / 108: model-specific repair kits
  • 4126 007 1051 — FS 88 gasket sethistorical listed item · FS 88 / 108: model-specific repair kits
  • 4135 007 1050 — FS 108 gasket sethistorical listed item · FS 88 / 108: model-specific repair kits
  • 0457 281 2104 — DIN A3 gasket panelhistorical listed item · FS 88 / 108: model-specific repair kits
  • 0783 830 2120 — Dirko crankcase sealanthistorical listed item · FS 88 / 108: model-specific repair kits
  • 0781 120 1111 — Oil-seal lube grease 370 ghistorical listed item · FS 88 / 108: model-specific repair kits

Service note · FS 88 / FS 108

FS 88 / 108: carburetor and leakage-test values

Basic screw settings are not final running adjustment or a complete leak-test procedure.

  • High-speed screw H and low-speed screw L: back off 1 FULL TURN each. Source calls this BASIC SETTING and says screws are initially “hard against their seats”; preserve this historical wording without converting it into a specified tightening torque or a recommendation to force delicate seats. Exact applicable carburetor service procedure remains necessary.
  • Full-load engine speed WITHOUT CUTTING TOOL 12000 rpm; idle 2800 rpm. The source wording is retained; these are not permission for unattended running or evidence of safe loaded-tool speed.
  • Carburetor leakage test closing pressure 0.8 bar (11.6 psi). Crankcase leakage test at GAUGE PRESSURE 0.5 bar (7.25 psi), and UNDER VACUUM 0.5 bar (7.25 psi magnitude below ambient). Vacuum is not positive 0.5 bar or an absolute pressure specification. No hold time, permitted decay or leak-rate tolerance is printed on page 7; none is invented.
  • Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.

Source: TI 37/1994, p. 4 · TI 37/1994, p. 7 — FS 88 / 108: carburetor and leakage-test values.

No additional parts-table entry added.

Service note · FS 88 / FS 108

FS 88 / 108: engine and ignition tightening torques

Model-specific clutch and crankcase fasteners must not be interchanged.

  • All pairs below are Nm / lbf.ft as printed; fastener identity and component remain part of the specification. No tightening sequence, lubricant or thread-locker condition is supplied by this table.
  • Crankcase spline screws: FS 88 IS-M 5x25, FS 108 IS-M 5x30, both 10.5 / 7.7. Cylinder to crankcase IS-M 5x16: 10.0 / 7.4. Clutch shoes: FS 88 flange screw M6 8.0 / 5.9; FS 108 hex-head M8x20 17.0 / 12.5.
  • Muffler to cylinder IS-M 5x16 and muffler to crankcase IS-M 5x12: each 10.5 / 7.7. Cover plate to muffler IS-M 4x12: 3.5 / 2.6. Clutch housing IS-M 5x16: 9.5 / 7.0. Flywheel and carrier M8 hexagon nuts: each 17.0 / 12.5.
  • Ignition module IS-M 5x20: 7.5 / 5.5. Spark plug M14x1.25: 19.0 / 14.0. Do not apply the FS 108 clutch-shoe torque to FS 88.
  • Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.

Source: TI 37/1994, p. 8 — engine and ignition tightening torques.

No additional parts-table entry added.

Service note · FS 88 / FS 108

FS 88 / 108: engine repair times and loaded-test footnote

Minutes assume trained personnel in a properly equipped workshop; one row has no time.

  • The single FS 88 / FS 108 column gives MINUTES for trained personnel in a properly equipped service workshop, not guaranteed elapsed time or labor pricing. This table may be added to the STIHL repair-times table. Asterisks mean TEST RUN UNDER LOAD, not a different unit or extra minutes.
  • Rows 1–4: remove/refit engine 10; crankcase, pressure test* 100; crankshaft/bearings, pressure test* 100; sealing rings, pressure test* 60. Rows 5–8: crankcase leakage test, test run 30; cylinder/piston, pressure test* 45; ignition system* 15; fuel supply/tank vent, test run 10.
  • Row 9 manifold or flange, pressure test: DASH, no time specified; not zero and not inferred from adjacent rows. Row 10 carburetor check* 25. The starred rows here are 2, 3, 4, 6, 7 and 10. Unstarred rows explicitly saying test run do not acquire an unprinted under-load requirement from this footnote.
  • Times are not a complete pressure-test, running or repair procedure. No extra minutes should be inferred by adding a second test run to a row whose named procedure already includes one.
  • Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.

Source: TI 37/1994, p. 12 — engine repair times and loaded-test footnote.

No additional parts-table entry added.

Wrong number or missing part for the FS 108? Report a correction →