Stihl 4135 · Section B · 2 of 14 · 28 parts
Rewind starter, Muffler
Fits FS 108.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4129 190 2000 | Carrier | 1 |
| 2 | 4215 195 7200 | Pawl | 1 |
| 3 | 0000 998 0607 | Torsion spring | 1 |
| 4 | 9460 624 0400 | E-clip 4 | 1 |
| 5 | 9443 825 7070 | Hollow rivet 7.15x0.4x3 | 1 |
| 6 | 9210 260 1100 | Hexagon nut M8 | 1 |
| 7 | 4126 190 0405 | Starter cover | 1 |
| 8 | not sold separately | Hollow rivet 6.5x0.5x5.8 not available as a separate item | 4 |
| 9 | 4126 084 9100 | Bushing | 1 |
| 10 | 4126 195 1600 | Rewind spring | 1 |
| 11 | 4215 195 0400 | Rope rotor | 1 |
| 12 | 4117 195 8200 | Starter rope Ø 3.5x800 mm | 1 |
| 13 | 4215 195 9000 | Washer | 1 |
| 14 | 9104 003 0960 | Self-tapping screw P5.5x12 | 1 |
| 15 | 4117 195 3400 | Starter grip | 1 |
| 16 | 4135 967 1500 | Model plate FS 108 | 1 |
| 17 | 9022 341 0980 | Spline screw IS-M5x16 | 6 |
| 18 | 4135 149 0600 | Muffler gasket | 1 |
| 19 | 4135 140 0600 | Muffler | 1 |
| 20 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 21 | 4135 149 0605 | Muffler gasket | 1 |
| 22 | 4135 145 1000 | Insert | 1 |
| 23 | 1113 141 9000 NLA | Screen | 1 |
| 24 | 4135 146 7300 | Cover plate | 1 |
| 25 | 9022 313 0610 | Spline screw IS-M4x6 | 4 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4126 190 4000 | Rewind starter | 1 |
| — | 0000 930 2203 | Starter rope Ø 3.5 mm x 30.5 m not illustratedoption | 1 |
| — | 4135 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · FS 88 / FS 108
FS 88 / 108: crankshaft repair limits
Connecting rod and big-end bearing are not replaceable separately.
- Compact two-stroke engine; smooth housing surfaces reduce dirt accumulation and aid cleaning; housing helps prevent hot-part contact and diverts exhaust gases and heated cooling air away from the operator. Large-volume muffler is described for silencing; no performance measurement is supplied.
- Crankcase is a two-part aluminium die casting with two dust-lip oil seals. Three-part crankshaft is pressed together before final machining; connecting rod and big-end bearing are NOT REPLACEABLE. Do not turn this construction description into a crankshaft pressing repair procedure.
- Aluminium-alloy piston has TWO compression rings. Piston pin runs in a needle cage and is secured by TWO HOOKLESS WIRE SNAP RINGS. Special-aluminium-alloy cylinder has an electroplated wear-resistant-alloy bore; no plating composition, bore-repair permission or pin diameter printed.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 2 · TI 37/1994, p. 3 — FS 88 / 108: crankshaft repair limits.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: starter rope and spring travel
Single-pawl starter uses 3.5 mm rope, 800 mm long.
- Rewind spring tension: 7 turns of the rope rotor; spare travel at least 1/2 turn. Rope diameter 3.5 mm (0.14 in), length 800 mm (31.5 in). These are source specifications, not a complete spring installation sequence; no spring part number is printed here.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 3 · TI 37/1994, p. 4 — FS 88 / 108: starter rope and spring travel.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: gearhead lubricant conflict
Page 5 names multipurpose grease; page 7 lists dedicated gear lubricant.
- SOURCE CONFLICT: section 4.2 page 5 specifies STIHL multipurpose grease 0781 120 1109 for the gearhead. Page 7 instead lists that multipurpose grease for DRIVE SHAFT and STIHL gear lubricant 0781 120 1117 / 1118 for GEARHEAD. Neither table is silently preferred; this does not establish that the products are interchangeable. Exact applicable service guidance is needed before choosing a lubricant.
- Page 7 multipurpose grease: 80 g (3 oz) 0781 120 1109; 225 g (8 oz) 0781 120 1110, drive shaft. Gear lubricant: 80 g (3 oz) 0781 120 1117; 225 g (8 oz) 0781 120 1118, gearhead. Package mass is NOT a fill quantity.
- Low-temperature lubricant 0781 417 1315, 100 ml (0.21 US pt) bottle, is for the starter rewind spring. No gearhead substitution or fill quantity is implied.
- Historical TI 37/1994 source guidance, not present-day approval, current stock or a physical interchange test. No serial cutoff is supplied. Exact-model catalog links are navigation, not proof that later service parts or carburetor variants equal the original configuration. No hardware operation was performed.
Source: TI 37/1994, p. 5 · TI 37/1994, p. 7 — FS 88 / 108: gearhead lubricant conflict.
Part numbers (5)
- 0781 120 1109 — Multipurpose grease 80 g; conflicting gearhead/drive-shaft allocationhistorical listed item · FS 88 / 108: gearhead lubricant conflict
- 0781 120 1110 — Multipurpose grease 225 g; drive shaft on page 7historical listed item · FS 88 / 108: gearhead lubricant conflict
- 0781 120 1117 — Gear lubricant 80 g; gearhead on page 7historical listed item · FS 88 / 108: gearhead lubricant conflict
- 0781 120 1118 — Gear lubricant 225 g; gearhead on page 7historical listed item · FS 88 / 108: gearhead lubricant conflict
- 0781 417 1315 — Low-temperature lubricant 100 ml; rewind springhistorical listed item · FS 88 / 108: gearhead lubricant conflict
Service note · FS 88 / FS 108
FS 88 / 108: starter, fuel and cover tightening torques
Two clamp-related rows have no torque specified.
- Pairs are Nm / lbf.ft. Fuel tank flange screw IS-M 5x14: 5.5 / 4.0. Starter cover top IS-M 5x16: 5.5 / 4.0; support/starter cover bottom AND support to clutch housing IS-M 5x16: 7.5 / 5.5. Special rope-rotor spline screw IS-P 5.5x12: 2.5 / 1.8.
- Carburetor IS-M 5x22: 5.5 / 4.0. Spacer flange to cylinder IS-M 5x25: 5.5 / 4.0. Shroud IS-M 5x12: 5.5 / 4.0.
- Adjusting screw in clamp IS-M 4x25 and clamp to spacer flange IS-M 5x16 each have a DASH, not a zero or a specified torque. Do not fill these explicitly unspecified rows with the generic M4/M5 values. Exact service instructions are needed.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 8 — starter, fuel and cover tightening torques.
No additional parts-table entry added.
Service note · FS 88 / FS 108
FS 88 / 108: control, starter and drive repair times
Rows 11–22 retain the common FS 88 / FS 108 minute column.
- MINUTES, trained personnel and properly equipped workshop: 11 bike handle and throttle control 10; 12 rewind starter, test run 15; 13 clutch, test run 20; 14 muffler 10; 15 air filter 5; 16 stop switch, test run 10.
- 17 clutch housing 20; 18 drive tube 25; 19 replace COMPLETE gearhead OR bearing housing 5; 20 limit stop OR deflector 10; 21 drive shaft 15; 22 fuel tank 15. Complete-unit replacement time is not a gearhead rebuild allowance. Bike-handle row does not specify a separate loop-handle time.
- None of rows 11–22 has the asterisk for test run under load; retain any explicit test-run wording without extending the starred-row footnote. These are historical labor-reference values, not permission to run a machine or evidence of a completed repair.
- Historical TI 37/1994 guidance, not current stock, a complete repair procedure or physical verification. Exact-model catalog links are navigation, not proof that later configurations are identical. No hardware operation was performed.
Source: TI 37/1994, p. 12 — control, starter and drive repair times.
No additional parts-table entry added.
Wrong number or missing part for the FS 108? Report a correction →