Stihl 4137 · Section F · 6 of 15 · 36 parts
Carburetor C1Q-S63A
Fits FC 75.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 120 7100 | Throttle shaft with lever | 1 |
| 2 | 1123 122 3000 | Spring | 1 |
| 3 | 4128 121 8900 | Pin | 1 |
| 4 | 4137 121 8600 | Washer | 1 |
| 5 | 1120 122 9000 | E-clip | 1 |
| 6 | 4229 121 3303 | Throttle shutter | 1 |
| 7 | 1125 122 7403 | Round head screw | 1 |
| 8 | 1125 122 9001 | E-clip | 1 |
| 9 | 1129 121 4800 | Pump diaphragm | 1 |
| 10 | 1123 129 0905 | Gasket | 1 |
| 11 | 1123 121 0800 | End cover | 1 |
| 12 | 1120 122 7800 | Oval head screw | 1 |
| 13 | 4116 121 5100 | Inlet needle | 1 |
| 14 | 1120 122 3004 | Spring | 1 |
| 15 | 1125 121 5000 | Inlet control lever | 1 |
| 16 | 1120 121 9200 | Spindle | 1 |
| 17 | 1120 122 6600 | Collar screw | 1 |
| 18 | 1129 129 0900 | Gasket → replaced by 4134 121 4700 TI 16/2009 | 1 |
| 19 | 4129 121 4700 | Metering diaphragm | 1 |
| 20 | 4140 120 2200 | Flange | 1 |
| 21 | 4226 122 7100 | Screw | 4 |
| 22 | 4229 122 6700 | High speed adjustment screw | 1 |
| 23 | 4229 122 6800 | Low speed adjustment screw | 1 |
| 24 | 1123 121 7800 | Strainer | 1 |
| 25 | 4140 121 0800 | End cover | 1 |
| 26 | 4226 121 2700 | Cap | 1 |
| 27 | 4229 122 6200 | Idle speed adjustment screw | 1 |
| 28 | 1125 122 4200 | Clamp | 1 |
| 29 | 4229 121 2700 | Cap | 1 |
| 30 | 4137 121 5603 | Fixed jet 0.34 | 1 |
| 31 | 4229 121 5800 | Pump piston | 1 |
| 32 | 4140 122 3600 | Sealing ring → replaced by 4314 122 3600 TI 20/2008 | 1 |
| 33 | 4229 122 3001 | Spring | 1 |
| 34 | 1120 121 7801 | Strainer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4137 120 0606 | Carburetor C1Q-S63A Fitment / change note → | 1 |
| — | 1129 007 1062 | Set of carburetor parts → replaced by 4128 007 1060, 4128 007 1060 TI 6/2009 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
C1Q-S63: limiter cap and historical service settings
The new matched-cylinder carburetor has a 270° H adjustment range; removed caps must not be reused.
- C1Q-S63, 4137 120 0606, is only the new-cylinder 4137 020 1202 configuration. C1Q-S45 and C1Q-S56 remain previous BIS/LD versions. Keep the page 2/page 7 serial conflict explicit; no common cutoff is asserted.
- Illustration identifies low-speed screw 1, high-speed screw 2, H limiter cap 3 and body stop pin 4. The cap pushes over the H screw head onto knurling; the body stop restricts adjustment to 270° (3/4 turn). Funnel-shaped cap interiors aid screwdriver insertion.
- For shop replacement of a damaged H screw or carburetor cleaning, pull the cap off with suitable pliers. Do not reuse removed caps because removal may damage them. Before adjustment inspect air filter, spark-arresting screen and fuel filter; clean or replace as necessary.
- Historical standard setting with H limiter cap removed: from lightly seated, open H 1½ turns. Install a NEW cap aligned to the rich stop and press fully home against the carburetor body. The illustration is the alignment reference; this is not permission to defeat a limiter.
- From lightly seated, open L one full turn counterclockwise. Use LA to set 2800 RPM and check with a tachometer; verify smooth acceleration through repeated throttle opening and smooth idle. These source settings apply to this stated configuration, not every 4137 or C1Q carburetor. No hardware adjustment was performed.
- User H adjustment is limited to 270° for conditions such as altitude or changing nylon-line/metal cutting tools. The TI refers the complete user procedure to the model owner manual, Adjusting the Carburetor. The exact owner-manual edition was not located in the retained inventory. Later workshop manuals have user-adjustment sections, but are not established as the referenced owner instructions. This is a documented source gap; this note is not the complete user procedure.
- Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.
Source: TI 16/2001, p. 5 · TI 16/2001, p. 6 · TI 16/2001, p. 7 — Sections 3.2–3.2.5: construction, cap handling, all service settings and summary.
Part numbers (4)
- 4137 120 0606 — Carburetor C1Q-S63New-generation matched configuration · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 020 1202 — Cylinder and pistonRequired matched cylinder · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 120 0603 — Carburetor C1Q-S45Older BIS generation · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 120 0604 — Carburetor C1Q-S56Older BIS replacement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Wrong number or missing part for the FC 75? Report a correction →