Stihl 4137 · Section C · 3 of 13 · 25 parts
Ignition system, Clutch
Fits FC 85.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 400 1200 | Flywheel | 1 |
| 2 | 4137 400 1350 | Ignition module Fitment / change note → | 1 |
| 3 | 4137 442 0400 | Insulating hose Fitment / change note → | 1 |
| 4 | 1106 405 1000 | Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 | 1 |
| 5 | 0000 998 0606 | Torsion spring | 1 |
| 6 | 4137 405 1600 | Plug connector | 1 |
| 7 | 4137 404 9300 | Washer Fitment / change note → | 2 |
| 8 | 9022 371 0710 | Spline screw IS-M4x20 Fitment / change note → | 2 |
| 9 | 4137 160 2001 | Clutch | 1 |
| 10 | 1129 162 0800 | Clutch shoe | 3 |
| 11 | 1127 162 3000 | Retainer | 3 |
| 12 | 0000 997 5625 | Tension spring | 3 |
| 13 | 1121 162 3000 | Retainer | 3 |
| 14 | 4137 080 1800 | Fan housing Fitment / change note → | 1 |
| 15 | 9991 003 5087 | Sleeve 7.5x6.8 | 3 |
| 16 | 9022 341 0980 | Spline screw IS-M5x16 | 4 |
| 17 | 4137 160 2900 | Clutch drum | 1 |
| 18 | 9455 621 1130 | Circlip 12x1 | 1 |
| 19 | 4137 791 9300 | Rubber insert | 1 |
| 20 | 9457 621 4481 | Circlip | 1 |
| 21 | 4137 790 7200 | Sleeve | 1 |
| 22 | 9075 478 4095 | Pan head self-tapping screw IS-D5x12 | 1 |
| 23 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 1 |
| 24 | 4137 080 1604 | Shroud | 1 |
| 25 | 4137 967 1509 | Model plate FC 85 | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 ignition: MB kit replaces MB or AD modules
Identify module type and retain its mounting sequence; introduction serials differ by model.
- Identify the module by its two-letter vendor type code and the final four STIHL part-number digits: AD (1304) versus MB (1307). A longer spark duration is the vendor-stated operating-range benefit, not a reproduced measurement. No complete AD ordering number is printed; do not derive one from 1304.
- Type MB4137 400 1307 was no longer supplied separately; kit 4137 400 1350 includes the MB module, mounting hardware and illustrated installation instructions and replaces either MB or AD. AD was not yet available as a spare. The page 8 drawing shows different mounting sequences for AD and MB; use the version-specific instructions, not an assumed common washer stack. Separate kit instructions were not located in the retained inventory. Later general ignition procedures do not establish the AD/MB-specific mounting stack; this remains a documented source gap.
- The summary retains two washers 4137 404 9300 and insulating tube 4137 442 0400, lists two new A5.3 washers 9291 021 0121, and changes two IS-M4 x 20 screws from 9022 313 0710 to 9022 371 0710. Old screws remain spares for other models. Insulating tube is not required for BG 75 or HS 75/80/85. No torque or air gap is specified here.
- Ignition introduction is model-specific: HS 80 from 2 49 943 796; FS 85 from 2 49 848 196; HT 75 from 2 50 062 280; other models in progress. These are not model production ranges or a universal update cutoff. Chapter 1 prints a different FS 85 update serial 2 49 849 196; retain both without replacing the ignition-specific statement.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 8 · TI 16/2001, p. 9 — Sections 4–4.4: ignition identification, mounting drawing, kit and summary.
Part numbers (7)
- 4137 400 1307 — Ignition module type MBPrevious separate module · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 400 1350 — Type MB ignition module kitReplacement for MB and AD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 404 9300 — Washer, twoUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 442 0400 — Insulating tubeUnchanged; omitted on BG 75 and HS 75/80/85 · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 9291 021 0121 — Washer A5.3, twoNew mounting hardware · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 9022 313 0710 — Screw IS-M4 x 20, twoPrevious; retained for other models · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 9022 371 0710 — Screw IS-M4 x 20, twoNew · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 fan housing: strengthened version, unchanged number
The lower housing is reinforced; the A/B drawing labels distinguish versions, not new order numbers.
- The lower part of fan housing 4137 080 1800 was strengthened. The drawing labels old 4137 080 1800 A and new 4137 080 1800 B; the summary explicitly keeps 4137 080 1800 unchanged. Do not turn A/B into invented order numbers.
- Only the modified version was supplied from the factory. Introduction refers to chapter 1; no clean numeric cutoff is assigned because the TI retains differing FS 85 serial statements.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 12 · TI 16/2001, p. 13 — Section 8 and continued summary: strengthened fan housing.
Part numbers (1)
- 4137 080 1800 — Fan housingSame number; modified lower section · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Wrong number or missing part for the FC 85? Report a correction →