← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section T · 19 of 21 · 20 parts

Gear head

Fits FR 85 T, FR 85.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131516171819223456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (20)

PosPart numberDescriptionQty
1 4130 641 0305 Gear housing 1
2 9503 003 9850 Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 2
3 not sold separately Drive pinion not available as a separate item 1
4 not sold separately Spur bevel gear not available as a separate item 1
5 4130 642 0601 Drive shaft 1
6 9503 003 5190 Grooved ball bearing 6001-2RS 1
7 9456 621 3100 Circlip 28x1.2 1
8 9503 003 9853 Grooved ball bearing 609-2Z 1
9 9455 621 0750 Circlip 9x1 1
10 9456 621 2660 Circlip 24x1.2 1
11 4119 713 6500 Screw plug 1
12 4137 710 3800 Thrust plate 1
13 not sold separately Guard washer not available as a separate item 1
15 4130 713 1600 Thrust washer 1
16 4126 642 7600 Collar nut M10x1 l/h thread 1
17 9075 478 4159 Pan head self-tapping screw IS-D5x24 2
18 4126 713 3100 Rider plate 1
19 0781 120 1117 Gear lubricant 80 g Fitment / change note → option 1
Not numbered on the diagram — assemblies, kits and options
— 4137 640 0100 Gearhead 1
— 4130 640 7301 Set of pinions 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · FR 85

FR 85: engine, speed and ignition specifications

Keep clutch, idle, electronic cutoff and rated output-shaft speeds distinct.

  • Engine: displacement 25.4 cm³ (1.55 cu.in), bore 34 mm (1.34 in), stroke 28 mm (1.10 in); power 0.9 kW (1.2 bhp) to ISO 8893. Rewind starter uses a SINGLE pawl and ElastoStart grip; starter-rope reference points to section 4. Fuel tank 0.44 l (0.92 US pt). These are the printed historical specifications, not measured values for a connected machine.
  • Clutch engages at 3700 rpm; idle speed is 2800 rpm. Electronic CUT-OFF RANGE WITHOUT CUTTING TOOL is 9700–11300 rpm. Maximum OUTPUT SHAFT speed (rated) is 7500 rpm. Do not treat output-shaft speed as an engine-speed setting, the cutoff range as an operating target with a blade, or clutch engagement as idle.
  • All-position diaphragm carburetor includes integral fuel pump. Standard L setting: OPEN ONE FULL TURN. Section 1 names L and LA only; no H-screw setting is supplied. Section 6.1 separately delegates carburetor adjustment to TI41/1997: this specification is not a complete adjustment/run-up procedure. No engine was started.
  • Ignition module includes an electronic speed limiter. SUPPRESSED spark plugs named: Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y. No plug gap or ignition air gap is stated here; none is inferred. Gear ratio is printed simply as 1.4, without a new tooth-count claim.
  • Weight is 9.4 kg (20.7 lb) WITHOUT CUTTING TOOL AND DEFLECTOR. No fuel-fill qualifier is printed in this weight line; do not silently label it dry, fueled or ready-to-cut weight. Later catalog assemblies remain references, not a reconstruction of every 1998 build.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 3 · TI 34/1998, p. 4 — Sections 2.1–2.3: complete mechanical, fuel, ignition, gearhead and weight specifications; acoustic table in companion note.

No additional parts-table entry added.

Historical fitment · FR 85

FR 85: ten approved cutting tools in the 1998 list

Six named heads, three cutting blades and one brush knife; no saw blade is listed.

  • Section 3 expressly approves the TEN listed tools for FR 85. Rows 1–6 are Supercut 20-2, Autocut 21-2, Autocut 25-2, Polymatic 30-2, Trimcut 30-2 and Polycut 20-3. Rows 7–9 are cutting blades 230-2, 230-4 and 230-8; row 10 is brush knife 250-3. Preserve each name/number pair; no circular saw blade or other cutting tool is added.
  • This approval list supplies NO fastening stack, torque, deflector conversion or harness/handle combination chart. Gearhead/deflector sheets are model context only; a shared later sheet does not prove every configuration is safe or complete. Section 4 transport guard is a TRANSPORT accessory, not an operating deflector. Full operational combination and safety requirements remain outside this short list.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 4 — Section 3 complete: ten approved cutting tools and exact numbers.

Part numbers (10)
  • 4002 710 2162 — STIHL Supercut 20-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2113 — STIHL Autocut 21-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2108 — STIHL Autocut 25-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2120 — STIHL Polymatic 30-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2122 — STIHL Trimcut 30-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2130 — STIHL Polycut 20-3Historically approved cutting tool · FR 85; exact historical application only
  • 4001 713 3804 — Cutting blade 230-2Historically approved cutting tool · FR 85; exact historical application only
  • 4001 713 3801 — Cutting blade 230-4Historically approved cutting tool · FR 85; exact historical application only
  • 4001 713 3803 — Cutting blade 230-8Historically approved cutting tool · FR 85; exact historical application only
  • 4112 713 4100 — Brush knife 250-3Historically approved cutting tool · FR 85; exact historical application only

Historical fitment · FR 85

FR 85: starter, guard, sharpening aid and separate lubricants

Drive/flexible-shaft grease differs from gearbox grease; transport guard covers four specified metal tools.

  • Transport guard 4119 790 3906 is listed for cutting blades 230-2, 230-4, 230-8 AND brush knife 250-3. It is not a running deflector. Later catalog V sheet has guard 4116 790 3901, diameter 350; no supersession/equivalence to the 1998 number is established by this TI. Preserve both sources independently.
  • ElastoStart 0000 190 3400 is the rewind-starter GRIP WITH ROPE; separate ElastoStart rope is printed 0000 195 8200. The retained starter sheet contains the exact grip and separate later rope options. Do not silently substitute a later rope length/diameter or resolve the earlier TI41/1997 rope-number conflict from this later listing.
  • STIHL gear lubricant for DRIVE SHAFT AND FLEXIBLE SHAFT: 80 g / 3 oz tube 0781 120 1109; 225 g / 8 oz tube 0781 120 1110. STIHL gear lubricant for GEARBOX: 80 g / 3 oz tube 0781 120 1117; 225 g / 8 oz tube 0781 120 1118. Identical generic lubricant labels do NOT make these two application groups interchangeable; no dosage or interval is supplied.
  • STIHL special oil 0781 417 1315, 100 ml / 3.5 fl.oz bottle: rewind spring AND BEARING BORE IN ROPE ROTOR. Sharpening template 4020 890 5500 is listed for BRUSH KNIFE; no blade angle, sharpening limit or circular-saw setting tool is specified here.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 4 — Section 4 accessory table and section 4.2 sharpening aid, every row and application.

Part numbers (9)
  • 4119 790 3906 — Transport guard for four named metal cutting toolsTransport accessory · FR 85; exact historical application only
  • 0000 190 3400 — ElastoStart grip with ropeStarter accessory · FR 85; exact historical application only
  • 0000 195 8200 — ElastoStart ropeSeparate historical starter rope · FR 85; exact historical application only
  • 0781 120 1109 — Shaft lubricant, 80 gDrive shaft and flexible shaft only · FR 85; exact historical application only
  • 0781 120 1110 — Shaft lubricant, 225 gDrive shaft and flexible shaft only · FR 85; exact historical application only
  • 0781 120 1117 — Gearbox lubricant, 80 gGearbox application · FR 85; exact historical application only
  • 0781 120 1118 — Gearbox lubricant, 225 gGearbox application · FR 85; exact historical application only
  • 0781 417 1315 — STIHL special oil, 100 mlRewind spring and rope-rotor bearing bore · FR 85; exact historical application only
  • 4020 890 5500 — Sharpening templateBrush knife · FR 85; exact historical application only

Service note · FR 85

FR 85: nylon-line sizes and a printed inch-value conflict

2.4 mm orange is listed for six heads; 2.7 mm red only for Polycut 20-3.

  • ORANGE 2.4 mm line is listed for Supercut 20-2, Autocut 21-2, Autocut 25-2, Polymatic 30-2, Trimcut 30-2 AND Polycut 20-3. RED 2.7 mm line is listed ONLY for Polycut 20-3. Do not widen the red-line row to all heads from the preceding row.
  • The ORIGINAL PAGE prints 2.4 mm / 0.95 inches for orange line. This is an internal unit conflict, not merely OCR: 2.4 / 25.4 is approximately 0.09449 inch, whereas 0.95 inch is 24.13 mm. Preserve the printed value as discrepant; do NOT offer 0.95-inch line or silently rewrite the source as a corrected specification. Red row prints 2.7 mm / 0.105 inches; retain its printed approximate pairing.
  • No line order number, spool length, fill length or feed procedure is printed in this table. No metal line substitute or other diameter/color is approved by this note.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 4 — Section 4.1 both line rows, colors, applications and original decimal discrepancy.

No additional parts-table entry added.

Wrong number or missing part for the FR 85 T, FR 85? Report a correction →