← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section U · 20 of 21 · 18 parts

Deflector

Fits FR 85 T, FR 85.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101011111212131415151616222333456778899
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (18)

PosPart numberDescriptionQty
1 4119 710 8103 Deflector 1
2 0000 716 3101 Backing plate 1
3 9022 373 1025 Spline screw IS-M5x23 4
4 4119 716 3203 Skirt 1
5 4119 710 6000 Blade 1
6 4118 713 4105 Blade 1
7 9074 478 4125 Pan head self-tapping screw IS-5x14 2
8 not sold separately O-ring 4x2 not available as a separate item 4
9 0000 716 3100 Backing plate 1
10 9074 478 2970 Pan head self-tapping screw IS-P4x10 2
11 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
12 9022 341 0980 Spline screw IS-M5x16 4
13 4133 007 1007 Deflector kit 1
14 4133 007 1008 Deflector kit 1
15 4133 713 4110 Blade 1
16 9074 478 4405 Pan head self-tapping screw IS-P6x14 1
Not numbered on the diagram — assemblies, kits and options
— 4119 007 1027 Deflector kit 1
— 0000 007 1300 Set of O-rings N 4x2-EPDM70 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FR 85

FR 85: ten approved cutting tools in the 1998 list

Six named heads, three cutting blades and one brush knife; no saw blade is listed.

  • Section 3 expressly approves the TEN listed tools for FR 85. Rows 1–6 are Supercut 20-2, Autocut 21-2, Autocut 25-2, Polymatic 30-2, Trimcut 30-2 and Polycut 20-3. Rows 7–9 are cutting blades 230-2, 230-4 and 230-8; row 10 is brush knife 250-3. Preserve each name/number pair; no circular saw blade or other cutting tool is added.
  • This approval list supplies NO fastening stack, torque, deflector conversion or harness/handle combination chart. Gearhead/deflector sheets are model context only; a shared later sheet does not prove every configuration is safe or complete. Section 4 transport guard is a TRANSPORT accessory, not an operating deflector. Full operational combination and safety requirements remain outside this short list.
  • Historical FR 85, series 4137, as described in TI34/1998. Shared FR 85 T catalog sheets do not extend this note to FR 85 T or other variants. No hardware operation was performed; no physical interchange test or current stock claim.

Source: TI 34/1998, p. 4 — Section 3 complete: ten approved cutting tools and exact numbers.

Part numbers (10)
  • 4002 710 2162 — STIHL Supercut 20-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2113 — STIHL Autocut 21-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2108 — STIHL Autocut 25-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2120 — STIHL Polymatic 30-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2122 — STIHL Trimcut 30-2Historically approved cutting tool · FR 85; exact historical application only
  • 4002 710 2130 — STIHL Polycut 20-3Historically approved cutting tool · FR 85; exact historical application only
  • 4001 713 3804 — Cutting blade 230-2Historically approved cutting tool · FR 85; exact historical application only
  • 4001 713 3801 — Cutting blade 230-4Historically approved cutting tool · FR 85; exact historical application only
  • 4001 713 3803 — Cutting blade 230-8Historically approved cutting tool · FR 85; exact historical application only
  • 4112 713 4100 — Brush knife 250-3Historically approved cutting tool · FR 85; exact historical application only

Wrong number or missing part for the FR 85 T, FR 85? Report a correction →