Stihl 4137 · Section B · 2 of 25 · 31 parts
Rewind starter, Muffler
Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (31)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 190 2002 | Carrier | 1 |
| 2 | 4133 195 7201 | Pawl | 1 |
| 3 | 0000 998 0612 | Torsion spring | 1 |
| 4 | 4137 190 0400 | Starter cover | 1 |
| 5 | 4137 190 1100 | Rope rotor with rewind spring Fitment / change note → | 1 |
| 6 | 0000 190 3403 | Starter grip ElastoStart Ø 2,7 mm Fitment / change note → | 1 |
| 7 | 4137 195 8200 | Starter rope Ø 2.7x910 mm Fitment / change note → | 1 |
| 8 | 0000 190 3400 | Starter grip ElastoStart Ø 3 mm Fitment / change note → → replaced by 0000 190 3403, 0000 190 3403 TI 42/1999 | 1 |
| 9 | 0000 195 8200 | Starter rope Ø 3x800 mm Fitment / change note → | 1 |
| 10 | 0000 195 7000 | Cap | 1 |
| 11 | 9104 003 0960 | Self-tapping screw P5.5x12 | 1 |
| 12 | 4137 967 1512 | Model plate FS 75 Fitment / change note → | 1 |
| 13 | 4137 967 1514 | Model plate FS 80 Fitment / change note → | 1 |
| 14 | 4137 967 1533 | Model plate FS 80 R | 1 |
| 15 | 4137 967 1515 | Model plate FS 85 Fitment / change note → | 1 |
| 16 | 4137 967 1531 | Model plate FS 85 R | 1 |
| 17 | 4137 967 1516 | Model plate FS 85 T Fitment / change note → | 1 |
| 18 | 4137 967 1532 | Model plate FS 85 RX | 1 |
| 20 | 0000 967 2129 | Nameplate MADE IN USA Fitment / change note → | 1 |
| 21 | 0000 967 2141 | Nameplate MADE IN BRAZIL | 1 |
| 22 | 4137 149 0600 | Muffler gasket | 1 |
| 23 | 4137 140 0602 | Muffler Fitment / change note → | 1 |
| 23 | 4137 140 0603 | Muffler | 1 |
| 24 | 9022 341 0980 | Spline screw IS-M5x16 | 6 |
| 25 | 4137 141 9000 | Screen Fitment / change note → | 1 |
| 40 | 4137 140 0600 | Muffler Fitment / change note → | 1 |
| 41 | 4137 141 9000 | Screen Fitment / change note → | 1 |
| 42 | 9099 021 0810 | Self-tapping screw 4.2x9.5 Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4137 190 4000 | Rewind starter | 1 |
| — | 0000 930 2281 | Starter rope Ø 2.7 mm x 30.8 m not illustratedoption | 1 |
| — | 0000 930 2208 NLA | Starter rope Ø 3 mm x 30.5 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 shroud replacement: retain the model identity
New shroud moves the company logo and requires a round model nameplate on an older machine.
- The new production shroud changes symbols/access for the three-adjusting-screw carburetor and prints STIHL on its front. The drawing shows H/L/LA access; the service replacement has fewer symbols, illustrated with LA only, so it can serve previous and new versions. The drawing is not a new carburetor adjustment specification.
- Shroud 4137 080 1604 replaces 4137 080 1601, with old stock supplied only while available. When fitting a logo-printed shroud to an old machine, bond the correct new model nameplate to the starter cover; chapter 6 lists twelve exact model assignments.
- The previous round self-adhesive company logo was on the starter cover; new machines print the logo on the shroud. If the old starter-cover logo is unavailable after repair, bond the correct round model nameplate to the starter cover. Neutral label 0000 967 2139 and MADE IN USA label 0000 967 2129 were supplied only while stocks lasted; the summary gives no direct replacement logo number.
- Introduction refers to chapter 1, whose FS 85 update serial 2 49 849 196 differs from the earlier BIS/ignition figure 2 49 848 196. No unified numeric cutoff is assigned.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 10 · TI 16/2001, p. 11 · TI 16/2001, p. 12 — Sections 5–7: shroud, model identity and logo relocation.
Part numbers (4)
- 4137 080 1601 — ShroudPrevious · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 4137 080 1604 — ShroudNew service replacement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 0000 967 2139 — STIHL nameplate neutralPrevious logo; stocks only · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
- 0000 967 2129 — STIHL nameplate MADE IN USAPrevious logo; stocks only · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T
4137 power tools: exact round nameplate assignments
Twelve models retain distinct old clipped and new self-adhesive nameplate numbers.
- Previous clipped model nameplates fit the old shroud; new round self-adhesive model nameplates are bonded to the starter cover. Previous versions remain spares for older machine versions. A shared engine or IPL sheet does not make model-name labels interchangeable.
- Use the exact model pair below when replacing the shroud or unavailable starter-cover company logo, as required by chapters 5 and 7. Introduction refers to chapter 1; no serial range is inferred.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 10 · TI 16/2001, p. 11 · TI 16/2001, p. 12 — Sections 5.2, 6 and 7.1: complete twelve-row nameplate summary.
Part numbers (24)
- 4137 967 1506 — FC 75 model nameplatePrevious clipped shroud label · FC 75 only; Previous clipped shroud label
- 4137 967 1513 — FC 75 model nameplateNew round starter-cover label · FC 75 only; New round starter-cover label
- 4137 967 1509 — FC 85 model nameplatePrevious clipped shroud label · FC 85 only; Previous clipped shroud label
- 4137 967 1519 — FC 85 model nameplateNew round starter-cover label · FC 85 only; New round starter-cover label
- 4230 967 1503 — FH 75 model nameplatePrevious clipped shroud label · FH 75 only; Previous clipped shroud label
- 4230 967 1508 — FH 75 model nameplateNew round starter-cover label · FH 75 only; New round starter-cover label
- 4137 967 1500 — FS 75 model nameplatePrevious clipped shroud label · FS 75 only; Previous clipped shroud label
- 4137 967 1512 — FS 75 model nameplateNew round starter-cover label · FS 75 only; New round starter-cover label
- 4137 967 1502 — FS 80 model nameplatePrevious clipped shroud label · FS 80 only; Previous clipped shroud label
- 4137 967 1514 — FS 80 model nameplateNew round starter-cover label · FS 80 only; New round starter-cover label
- 4137 967 1501 — FS 85 model nameplatePrevious clipped shroud label · FS 85 only; Previous clipped shroud label
- 4137 967 1515 — FS 85 model nameplateNew round starter-cover label · FS 85 only; New round starter-cover label
- 4137 967 1510 — FS 85 T model nameplatePrevious clipped shroud label · FS 85 T only; Previous clipped shroud label
- 4137 967 1516 — FS 85 T model nameplateNew round starter-cover label · FS 85 T only; New round starter-cover label
- 4230 967 1500 — HL 75 model nameplatePrevious clipped shroud label · HL 75 only; Previous clipped shroud label
- 4230 967 1505 — HL 75 model nameplateNew round starter-cover label · HL 75 only; New round starter-cover label
- 4230 967 1501 — HL 75 K model nameplatePrevious clipped shroud label · HL 75 K only; Previous clipped shroud label
- 4230 967 1506 — HL 75 K model nameplateNew round starter-cover label · HL 75 K only; New round starter-cover label
- 4138 967 1505 — HT 70 model nameplatePrevious clipped shroud label · HT 70 only; Previous clipped shroud label
- 4138 967 1502 — HT 70 model nameplateNew round starter-cover label · HT 70 only; New round starter-cover label
- 4138 967 1500 — HT 75 model nameplatePrevious clipped shroud label · HT 75 only; Previous clipped shroud label
- 4138 967 1503 — HT 75 model nameplateNew round starter-cover label · HT 75 only; New round starter-cover label
- 4602 967 1500 — KW 85 model nameplatePrevious clipped shroud label · KW 85 only; Previous clipped shroud label
- 4602 967 1501 — KW 85 model nameplateNew round starter-cover label · KW 85 only; New round starter-cover label
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76
TI24/2002: three starter-rope stages and model scope
Keep the original, interim and final rope sizes separate; HS72/74/76 do not inherit the grip change.
- Original starter rope 4123 195 8200 is 0.105 in / 2.7 mm diameter and 31.5 in / 800 mm long. Interim rope 0000 195 8200 is 0.120 in / 3 mm diameter and the same 31.5 in / 800 mm length. Final rope 4137 195 8200 returns to 0.105 in / 2.7 mm diameter but increases length to 35.8 in / 910 mm. Do not confuse unchanged diameter with unchanged length.
- The interim rope is included in ElastoStart 0000 190 3400; the final rope is used in ElastoStart 0000 190 3403. Those grip associations describe the main starter branch; section 2.7 extends subsections 2.1, 2.3, 2.4 and 2.5 to HS 72, HS 74 and HS 76, but not subsection 2.2. No ElastoStart-grip replacement is authorized for those three models by this TI.
- Summary remarks distinguish earlier-to-interim from interim-to-new changes. Original rope 4123 195 8200 and interim rope 0000 195 8200 remain available for other models; their removal from this branch does not mean universal discontinuation. Section 2.6 states the new starter parts are fully interchangeable with previous machine versions within the applicable section 2 model scope.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (3)
- 4123 195 8200 — Starter rope 2.7 x 800 mmOriginal; retained for other models · Named section 2 models only; see conditions
- 0000 195 8200 — Starter rope 3 x 800 mmInterim; retained for other models · Named section 2 models only; see conditions
- 4137 195 8200 — Starter rope 2.7 x 910 mmFinal version · Named section 2 models only; see conditions
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85
TI24/2002: ElastoStart grip change excludes HS72/74/76
The new grip follows the longer final rope; do not extend subsection2.2 to the restricted hedge-trimmer group.
- ElastoStart grip 0000 190 3403 replaces 0000 190 3400 together with the introduction of final rope 4137 195 8200 (2.7 x 910 mm). The old grip includes interim rope 0000 195 8200 (3 x 800 mm); the new grip includes the final rope. Summary rows 4–7 preserve these assembly contents.
- The old grip and interim rope remain available for other models. Full starter modifications also apply to BG 72, BG 75, FC 72, FS 72, FS 74, FS 76, HS 75, HS 80 and HS 85. HS 72, HS 74 and HS 76 are deliberately excluded from this grip note: their subsection list omits 2.2.
- The section 2.6 interchangeability statement belongs to this starter update; it does not remove the explicit model/subsection limitation or the separate control-handle retrofit conditions.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (4)
- 0000 190 3400 — ElastoStart grip with interim ropePrevious; retained for other models · Named section 2 models only; see conditions
- 0000 190 3403 — ElastoStart grip with final ropeNew · Named section 2 models only; see conditions
- 0000 195 8200 — Starter rope 3 x 800 mmOld grip content · Named section 2 models only; see conditions
- 4137 195 8200 — Starter rope 2.7 x 910 mmNew grip content · Named section 2 models only; see conditions
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76
TI24/2002: rope rotor and spring supplied as an assembly
Preserve the interim-rotor availability conflict; new rotor and spring are not separate spares.
- Original rope rotor 4133 195 0400 was replaced by interim rotor 4133 195 0470. The TI says the interim rotor is no longer available separately and the rewind spring 4133 195 1600 is likewise supplied only as part of rope rotor with rewind spring 4137 190 1100. The new assembly contains the rotor and spring; no independent new numbers are given for either component.
- The starter drawing labels rope (1), ElastoStart grip (2), rotor (3), spring (4), and rotor/spring assembly (5). These are not the summary-table row numbers: assembly 4137 190 1100 is summary item 8, with its spring and rotor as items 9 and 10.
- Preserved source tension: prose and summary remark 4 say the interim rotor is no longer available from the factory, while summary item 10 (previous rotor 4133 195 0470) carries remark 3 permitting previous stock until exhausted. Spring item 9 also carries the stock remark despite prose saying it is no longer separate. New separate items are explicitly unavailable under remark 6; use assembly item 8. Do not silently collapse these phase/stock statements into a current availability promise.
- Section 2.7 explicitly extends subsections 2.3–2.5, as well as rope subsection 2.1, to HS 72, HS 74 and HS 76. The broader group receives all starter modifications. Section 2.6 states full interchangeability with previous versions within this starter scope, not a control-handle equivalence rule. All other parts are stated unchanged.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (4)
- 4133 195 0400 — Rope rotorOriginal; stocks-only phase · Named section 2 models only; see conditions
- 4133 195 0470 — Rope rotorInterim; conflicting separate-stock statements · Named section 2 models only; see conditions
- 4133 195 1600 — Rewind springPrevious separate part; stock/assembly statements retained · Named section 2 models only; see conditions
- 4137 190 1100 — Rope rotor with rewind springNew assembly; includes both components · Named section 2 models only; see conditions
Historical fitment · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R
FS 75 / 80 / 85: ElastoStart and lubricant distinctions
3400 is the grip-with-rope assembly; TI calls 8200 a grip while the later IPL calls it starter rope. Drive-shaft grease and gear lubricant stay separate.
- Section 4 lists ElastoStart grip 0000 190 3400 for the rewind starter, explicitly GRIP WITH ROPE. It separately labels 0000 195 8200 ElastoStart grip without that remark. Later exact-family IPL instead calls 0000 195 8200 starter rope Ø3 × 800 mm. Preserve this source DESCRIPTION CONFLICT; do not present two interchangeable complete grips or silently correct the TI.
- The later IPL identifies 3400 as Ø3 mm and also lists 3403/Ø2.7 mm with 1999 TI annotations. This 1996 bulletin supplies no standalone rope dimension, no 3403 replacement and no serial cutoff. No later revision is promoted into this historical row.
- STIHL multipurpose grease 0781 120 1109, 80 g (3 oz) tube, is for the DRIVE SHAFT. STIHL gear lubricant 0781 120 1117, 80 g (3 oz) tube, is for the GEARHEAD (FS 80/85). Tube content is a sales pack size, NOT an instruction to fill either assembly with 80 g; no service fill quantity or interval is printed.
- Scope is the 1996 series 4137 introduction, including depicted R and RB handle arrangements. No scope is inherited by FS 85 T/RX, FC/FR/HL/HT/KM/KW/SP models or later same-named machines from a shared IPL sheet. Historical source guidance, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 36/1996, p. 3 · TI 36/1996, p. 5 — FS 75 / 80 / 85: ElastoStart and lubricant distinctions.
Part numbers (4)
- 0000 190 3400 — ElastoStart grip with ropeExplicit complete grip/rope row · FS 75/80/85 rewind starter
- 0000 195 8200 — TI: ElastoStart grip; later IPL: starter ropeDescription conflict retained · Do not infer a second complete grip assembly
- 0781 120 1109 — Multipurpose grease, 80 g tubeDrive-shaft lubricant · FS 75/80/85 drive shaft; pack size not fill quantity
- 0781 120 1117 — Gear lubricant, 80 g tubeGearhead lubricant · FS 80/85 gearhead; pack size not fill quantity
Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85 / BG 72 / FC 72 / FS 48 / FS 52 / FS 56 / FS 62 / FS 66 / FS 72 / FS 74 / FS 76 / HS 72 / HS 74 / HS 76
ElastoStart replacement rope: original-number conflict retained
New 0000 195 8200 is3.0×800 mm; prose and table disagree on the original.
continuously — Continuous introduction; no numeric boundary supplied for this particular change.
- Section 3 prose prints ORIGINAL 4123 190 4000 (2.7×900 mm), replaced for some time by ELASTOSTART 0000 195 8200 (3.0×800 mm). The summary instead prints ORIGINAL 4123 195 8200. Both are confirmed on the original scan: retain the UNRESOLVED NUMBER CONFLICT, not an OCR correction, proven equivalence or two-step supersession.
- In addition to cover models, the source explicitly extends this change to BG 72, FC 72, FS 48/52/56/62/66/72/74/76 and HS 72/74/76. These are the historical configurations: not the later type 4144 FS 56 or type 4112 FS 80.
- Modification introduced CONTINUOUSLY; summary remark says ORIGINAL NO LONGER AVAILABLE FROM FACTORY. No machine-number cutoff, handle assembly replacement, knot procedure or permission to shorten either rope to an unprinted length is given. Catalog associations expose the historical note without rewriting their rope rows or choosing which conflicting original is correct.
- Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.
Source: TI 41/1997, p. 5 — Entire section 3 prose, extended model list, summary and availability remark.
Part numbers (3)
- 4123 190 4000 — Original rope number printed in prose;2.7×900 mmConflicts with summary original · Only the named TI 41/1997 configurations and conditions
- 4123 195 8200 — Original rope number printed in summaryConflicts with prose original · Only the named TI 41/1997 configurations and conditions
- 0000 195 8200 — ElastoStart rope;3.0×800 mmReplacement · Only the named TI 41/1997 configurations and conditions
Conditional replacement · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75
FC / FS / HL / HT: new muffler requires new gasket AND shroud
TI30/1998 limits conversion of the six named models; screen remains regional and changes from screw to tab retention.
2 38 993 300 — New muffler/shroud and modified gasket from this machine serial onwards; original-machine retrofit remains conditional.
- Applies only to FC 75, FS 75, FS 80, FS 85, HL 75 and HT 75. From serial number 2 38 993 300 ONWARDS, the original muffler and shroud are replaced by new versions and the gasket is modified. The source prints types 4137 (FC/FS), 4230 (HL) and 4138 (HT); retained assembly grouping under 4137 does not rewrite these printed types.
- In ORIGINAL machine versions: replacing an original muffler with the NEW muffler REQUIRES BOTH the new gasket AND new shroud. Separately, the NEW shroud and NEW gasket can each be fitted INDEPENDENTLY in original machines. These are directional service rules, not unrestricted interchange or authorization to put an old muffler/shroud on a new machine.
- Exact named models only: shared sheets and reused numbers do not add FS 80 R, FS 85 R/T/RX, HL 75 K, HT 70, FC 85, FH 75, FR 85, KW 85, KM 85 or other models. Historical factory availability is not current stock or regional legal approval. No physical interchange was verified. No hardware operation was performed.
- Muffler table item 01: original 4137 140 0600 → new 4137 140 0602. The original description contains items 02 (screen) and 03 (self-tapping screw). Screen item 02 remains 4137 141 9000 in BOTH columns. Item 03 is C4.2x9.5 screw 9099 021 0810 in the original column and --- in the new column; the new screen is retained by a TAB, not that screw. A dash is not an invented replacement number.
- Figure 392TI018 KN identifies original muffler (1) and new (2), longer air outlet cowling (6), deflector in front of it (7) and screen (8). The screen statement is specifically ONLY for mufflers for USA, CDN and AUS, not every regional muffler and not permission to remove a required screen.
- The conversion companions are MODIFIED gasket 4137 149 0600 (number unchanged) and NEW shroud 4137 084 0900. Number alone cannot distinguish old/new gasket geometry. Original shroud is 4137 080 1600. Both companions are required when replacing the original muffler with the new one.
- Table remark 1: original muffler and original screw remain available. The screen row has no numbered remark and retains its number. These statements do not waive the conversion rule. Retained B sheets bind exact named models and the new muffler, gasket and screen; HT shared sheet also has a different original muffler row, which is not silently substituted for this TI original number.
Source: TI 30/1998, p. 1 · TI 30/1998, p. 2 — Both complete pages: model scope, serial cutoff, identification figures, two service rules, all six table rows and remarks.
Part numbers (4)
- 4137 140 0600 — Original muffler; table item 01Original; remark 1 remains available · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
- 4137 140 0602 — New muffler; table item 01Conditional conversion; new gasket AND shroud required · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
- 4137 141 9000 — Screen; table item 02Unchanged number; USA/CDN/AUS screen restriction · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
- 9099 021 0810 — Self-tapping screw C4.2x9.5; table item 03Original only; new column ---; remark 1 · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →