← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section C · 3 of 25 · 29 parts

Ignition system, Clutch

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516161718192202122232425262728344056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (29)

PosPart numberDescriptionQty
1 4137 400 1200 Flywheel Fitment / change note → 1
2 4137 400 1350 Ignition module Fitment / change note → 1
3 4137 442 0400 Insulating hose Fitment / change note → 1
4 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
5 0000 998 0606 Torsion spring 1
6 4137 405 1600 Plug connector 1
7 4137 404 9300 Washer Fitment / change note → 2
8 9022 371 0710 Spline screw IS-M4x20 Fitment / change note → 2
9 4137 160 2001 Clutch 1
10 1129 162 0800 Clutch shoe 3
11 1127 162 3000 Retainer 3
12 0000 997 5625 Tension spring 3
13 1121 162 3000 Retainer 3
14 4137 080 1800 Fan housing Fitment / change note → 1
15 9991 003 5087 Sleeve 7.5x6.8 3
16 9022 341 0980 Spline screw IS-M5x16 4
17 4137 160 2900 Clutch drum 1
18 9455 621 1130 Circlip 12x1 1
19 4137 791 9300 Rubber insert 1
20 9457 621 4481 Circlip 1
21 4137 790 7200 Sleeve 1
22 9075 478 4095 Pan head self-tapping screw IS-D5x12 1
23 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
24 4137 080 1604 Shroud 1
25 4137 967 1500 Model plate FS 75 1
26 4137 967 1502 Model plate FS 80 1
27 4137 967 1501 Model plate FS 85 1
28 4137 967 1510 Model plate FS 85 T 1
40 4137 084 8300 Reflector foil Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · FS 75 / FS 80 / FS 85 / FR 85 / FC 75

FS 75 / FS 80 / FS 85 / FR 85 / FC 75: series 4137 replacement ignition assignment

4137 400 1307 with flywheel 4137 400 1200; ignition lead not replaceable.

  • Printed series 4137. Use 4137 400 1307 with flywheel 4137 400 1200.
  • The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4137 400 1307 — Replacement ignition moduleAssigned component · FS 75 / FS 80 / FS 85 / FR 85 / FC 75, printed series 4137, listed combination only
  • 4137 400 1200 — Assigned flywheelRequired pairing · FS 75 / FS 80 / FS 85 / FR 85 / FC 75, printed series 4137

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T

4137 ignition: MB kit replaces MB or AD modules

Identify module type and retain its mounting sequence; introduction serials differ by model.

  • Identify the module by its two-letter vendor type code and the final four STIHL part-number digits: AD (1304) versus MB (1307). A longer spark duration is the vendor-stated operating-range benefit, not a reproduced measurement. No complete AD ordering number is printed; do not derive one from 1304.
  • Type MB4137 400 1307 was no longer supplied separately; kit 4137 400 1350 includes the MB module, mounting hardware and illustrated installation instructions and replaces either MB or AD. AD was not yet available as a spare. The page 8 drawing shows different mounting sequences for AD and MB; use the version-specific instructions, not an assumed common washer stack. Separate kit instructions were not located in the retained inventory. Later general ignition procedures do not establish the AD/MB-specific mounting stack; this remains a documented source gap.
  • The summary retains two washers 4137 404 9300 and insulating tube 4137 442 0400, lists two new A5.3 washers 9291 021 0121, and changes two IS-M4 x 20 screws from 9022 313 0710 to 9022 371 0710. Old screws remain spares for other models. Insulating tube is not required for BG 75 or HS 75/80/85. No torque or air gap is specified here.
  • Ignition introduction is model-specific: HS 80 from 2 49 943 796; FS 85 from 2 49 848 196; HT 75 from 2 50 062 280; other models in progress. These are not model production ranges or a universal update cutoff. Chapter 1 prints a different FS 85 update serial 2 49 849 196; retain both without replacing the ignition-specific statement.
  • Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.

Source: TI 16/2001, p. 8 · TI 16/2001, p. 9 — Sections 4–4.4: ignition identification, mounting drawing, kit and summary.

Part numbers (7)
  • 4137 400 1307 — Ignition module type MBPrevious separate module · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 400 1350 — Type MB ignition module kitReplacement for MB and AD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 404 9300 — Washer, twoUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 442 0400 — Insulating tubeUnchanged; omitted on BG 75 and HS 75/80/85 · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 9291 021 0121 — Washer A5.3, twoNew mounting hardware · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 9022 313 0710 — Screw IS-M4 x 20, twoPrevious; retained for other models · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 9022 371 0710 — Screw IS-M4 x 20, twoNew · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T

4137 fan housing: strengthened version, unchanged number

The lower housing is reinforced; the A/B drawing labels distinguish versions, not new order numbers.

  • The lower part of fan housing 4137 080 1800 was strengthened. The drawing labels old 4137 080 1800 A and new 4137 080 1800 B; the summary explicitly keeps 4137 080 1800 unchanged. Do not turn A/B into invented order numbers.
  • Only the modified version was supplied from the factory. Introduction refers to chapter 1; no clean numeric cutoff is assigned because the TI retains differing FS 85 serial statements.
  • Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.

Source: TI 16/2001, p. 12 · TI 16/2001, p. 13 — Section 8 and continued summary: strengthened fan housing.

Part numbers (1)
  • 4137 080 1800 — Fan housingSame number; modified lower section · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only

Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R

FS 75 / 80 / 85: two stop-wire arrangements and ignition data

The one-wire version uses the throttle cable for the stop-circuit function; do not assume the two control versions have identical wiring.

  • Figure 392TI002 identifies control handle (1) with TWO short-circuit wires and version (2) with ONE short-circuit wire on the ignition module. In the one-wire version the throttle cable performs the functions of the short-circuit wires. The drawing shows the different STOP/START markings, not a numbered terminal pinout or a conversion procedure.
  • The new control handle has fewer component parts and functions as on FS 72/74/76/86/88/106/108. Functional similarity does not authorize swapping handles/cables/modules or extending this exact wire arrangement to those earlier machines. No wire count is assigned to an individual new model, serial or market in this TI.
  • Ignition timing is 1.55–2.25 mm (0.060–0.090 in) BEFORE TDC at 8,000 rpm; ignition lead length 160 mm (6.3 in). Suppressed spark plugs: Bosch WSR 6F, NGK BPMR 7 A or Champion RCJ 6Y. No spark-plug gap, module air gap or plug torque is supplied here; none is inferred from other engines.
  • Scope is the 1996 series 4137 introduction, including depicted R and RB handle arrangements. No scope is inherited by FS 85 T/RX, FC/FR/HL/HT/KM/KW/SP models or later same-named machines from a shared IPL sheet. Historical source guidance, not current stock or verified physical interchange. No hardware operation was performed.

Source: TI 36/1996, p. 2 · TI 36/1996, p. 4 — FS 75 / 80 / 85: two stop-wire arrangements and ignition data.

No additional parts-table entry added.

Service note · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85

Nine models: paired carburetor and electronic speed-limitation change

Keep each printed X-prefixed introduction number tied to its exact model.

FC 75: X 37 801 959; FS 75: X 37 878 261; FS 80: X 37 759 999; FS 85: X 37 838 653; HL 75: X 37 761 799; HS 75, HS 80 and HS 85: X 37 810 310; HT 75: X 37 772 428 — Exact model-conditioned introduction of the paired production change; not a continuous model identity range.

  • At the listed machine numbers the production carburetor WITH SPEED CONTROL VALVE (drawing 3, arrow) changes to a version WITHOUT it (drawing 4), AT THE SAME TIME as introduction of an ignition module with ELECTRONIC SPEED LIMITATION (ESL). Removing the valve alone is not the described change.
  • FC 75: X 37 801 959; FS 75: X 37 878 261; FS 80: X 37 759 999; FS 85: X 37 838 653; HL 75: X 37 761 799; HS 75, HS 80 and HS 85: X 37 810 310; HT 75: X 37 772 428. These are model-conditioned introduction markers, not model-identification intervals; retain the printed X prefix. BG 75 has NO entry in this table. FS 80 here is TYPE 4137, not the older type 4112 FS 80.
  • The page2 table is actually headed1.3.1, while the summary refers to1.2.1; this numbering inconsistency is preserved, not a missing table. Section 1.2.2.3 keeps the individual maximum-speed ranges and carburetor settings UNCHANGED, with no numeric values supplied.
  • Cover types: BG 75 4227; HS 75/80/85 4226; HL 75 4230; HT 75 4138; FS 75/80/85 and FC 75 4137. The catalog groups HL/HT power-unit sheets under 4137; that folder is not a correction to the cover type identities. Service replacement carburetors follow separate rules below.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 1 · TI 41/1997, p. 2 · TI 41/1997, p. 4 — Section 1.2, complete introduction table and drawing 366TI020 KN; section 1.2.2.3; cover types.

No additional parts-table entry added.

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85

ESL ignition modules: 1306/1307 marking and the optional BG/HS hose

1307 adds the insulating hose and is the general replacement.

  • WHEN DISASSEMBLED, marking XXXX = 1306 OR 1307 identifies an ESL module. Drawing366TI021 KN reads STIHL 4137 XXXX A and calls the hose5; that drawing callout is not summary item 5. No complete order number is invented for marking 1306.
  • Version 1307 differs from 1306 ONLY THROUGH THE ADDITIONAL INSULATING HOSE on the ignition cable and is generally supplied as a replacement. BG AND HS machines DO NOT REQUIRE the hose, but MAY INSTALL THE NEW MODULE WITH THE HOSE.
  • Summary module 4137 400 1305 becomes 4137 400 1307 INCLUDING ITEM 2, hose 4137 442 0400 unchanged. Remark1 says original NO LONGER AVAILABLE FROM FACTORY. The BG 75 paragraph separately permits residual 1305 stock ONLY FOR BG 75; this is not general permission to install a non-ESL module elsewhere.
  • For listed machines without a carburetor speed-control valve, the service rule requires 4137 400 1307 with ESL; BG 75 has the explicitly separate fan-load exception. Marking identification alone is not an operating test or permission to bypass speed limiting.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 3 · TI 41/1997, p. 4 — Section 1.2.2.1 and drawing 366TI021 KN; section 1.2.2.2; summary ignition module/item 2/remark1.

Part numbers (3)
  • 4137 400 1305 — Original ignition moduleNo longer factory supplied; BG 75 residual-stock exception · Only the named TI 41/1997 configurations and conditions
  • 4137 400 1307 — Replacement ESL ignition module including hose item 2General replacement · Only the named TI 41/1997 configurations and conditions
  • 4137 442 0400 — Insulating hose; summary item 2Unchanged part number · Only the named TI 41/1997 configurations and conditions

Conditional replacement · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75

FC / FS / HL / HT: shroud, reflector foil and same-number gasket revision

New shroud and modified gasket can independently fit original machines; neither is optional in the new-muffler conversion.

2 38 993 300 — New muffler/shroud and modified gasket from this machine serial onwards; original-machine retrofit remains conditional.

  • Applies only to FC 75, FS 75, FS 80, FS 85, HL 75 and HT 75. From serial number 2 38 993 300 ONWARDS, the original muffler and shroud are replaced by new versions and the gasket is modified. The source prints types 4137 (FC/FS), 4230 (HL) and 4138 (HT); retained assembly grouping under 4137 does not rewrite these printed types.
  • In ORIGINAL machine versions: replacing an original muffler with the NEW muffler REQUIRES BOTH the new gasket AND new shroud. Separately, the NEW shroud and NEW gasket can each be fitted INDEPENDENTLY in original machines. These are directional service rules, not unrestricted interchange or authorization to put an old muffler/shroud on a new machine.
  • Exact named models only: shared sheets and reused numbers do not add FS 80 R, FS 85 R/T/RX, HL 75 K, HT 70, FC 85, FH 75, FR 85, KW 85, KM 85 or other models. Historical factory availability is not current stock or regional legal approval. No physical interchange was verified. No hardware operation was performed.
  • Table item 04 gasket: 4137 149 0600 in BOTH columns, but the shape is modified for improved air guidance. Remark 2 says ONLY the MODIFIED version is now available from the factory. Figure 392TI020 KN (5) shows the revised outline with arrows/dashed comparison at the left side; no dimensions or cutting template are supplied. Do not treat the unchanged number as unchanged geometry.
  • Table item 05: original shroud 4137 080 1600 → new shroud 4137 084 0900. Original description includes item 06 reflector foil 4137 084 8300; new foil column is ---. Remark 3 limits original-shroud availability to WHILE STOCKS LAST. Remark 1 keeps the ORIGINAL reflector foil available, not fitted to every new shroud.
  • Figure 392TI019 KN identifies original shroud (3), new shroud (4), larger exhaust-gas outlet (9) and modified cooling slits. The starter-side rib pointing toward the muffler AND its attached reflector foil are eliminated. This is not an instruction to strip foil from an original shroud or omit both conversion companions.
  • Retained C sheets list shroud 4137 080 1604, NOT either TI shroud number, while retaining the exact original foil 4137 084 8300. Binding preserves model context and the foil row only; later shroud relationship is UNESTABLISHED and the canonical IPL is not overwritten. New and original TI numbers remain separate source assertions. Printed 4137/4230/4138 types are not inferred from the shared catalog container.

Source: TI 30/1998, p. 1 · TI 30/1998, p. 2 — Both complete pages: model scope, serial cutoff, identification figures, two service rules, all six table rows and remarks.

Part numbers (4)
  • 4137 149 0600 — Muffler gasket; item 04, both columnsSame number; changed shape; remark 2 modified version only · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
  • 4137 080 1600 — Original shroud; item 05 includes foil item 06Remark 3; while stocks last · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
  • 4137 084 0900 — New shroud; item 05Independent original-machine fit; required for new muffler conversion · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only
  • 4137 084 8300 — Original reflector foil; item 06New column ---; remark 1 original remains available · FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75; TI30/1998 conditions only

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FS 75 / FS 80 / FS 85

FH/HL/HT/FC/FS: the new shroud fits both engine versions

Shroud 1601 includes its insert; the old 1600 ends factory supply, without authorizing mixed intake parts.

1 42 812 154 — Announced uprated engine-component introduction on original-cover models; retain matched configurations and the shroud exception.

  • The new shroud is modified around the carburetor-adjusting screws so it can be used with original and new carburetors and machines. The comparison shows the original L/LA markings and new L/LD/LA arrangement. These access markings do not imply that both carburetor idle systems are adjusted together.
  • The inside-view drawing identifies an insert (1). The source says an improved shroud with insert has been available for some time; it improves mounting of the shroud and starter cover to the crankcase. The new shroud is supplied with the insert. The bulletin's serial introduction does not date the first appearance of every earlier insert-equipped shroud.
  • Summary item 22 consists of item 23. Item 23 has a dash for the previous number and -*- for the new number, with remark 5: not available as a separate item. Neither symbol is a part number; no insert number or quantity is invented.
  • The later exact-model ignition/clutch catalog sheets list shroud 4137 080 1604, not the historical 1600/1601 pair. That discrepancy is retained without an invented 1601-to-1604 supersession or historical drawing position. The separately listed rubber insert 4137 791 9300 is not assumed to be the unnumbered shroud insert.
  • The original USA cover names FH 75 (series 4230), HL 75 and HL 75 K (4230), HT 70 and HT 75 (4138), FC 75 and FS 75/80/85 (4137). FR 85 appears in extracted title metadata but not this original cover or page-8 model list; this note does not infer FR 85, FS R/T/RX, FC 85, KW, SP or KM applicability from shared parts or shared catalog sheets.
  • The announced production introduction is from serial 1 42 812 154. This is not a universal serial-to-model selector, proof of the configuration now fitted, or a date inferred from the later catalog. Historical availability statements are not current stock claims.
  • For separate filter-housing, carburetor or spacer-flange replacement, original machines require original versions and new machines require new versions. Mixing original and new versions may cause loss of power and engine-running problems. The filter housing and choke shutter must also be a matched original/original or new/new pair. The new shroud is the explicit cross-version exception.
  • Increasing engine power requires all the new parts together with an ignition module with electronic maximum-speed cut-off. Earlier-machine service notes additionally require TI41/1997 section 1.3 and, for the stated carburetor replacement, its supplied instruction sheet to determine the ignition-module requirement; they are not replaced by this component note. The earlier-machine drawing specifies gaskets 4114 149 1205 on both sides of the heat shield. No ignition-module number, cut-off rpm or blanket conversion approval is invented.
  • TI21/1999 is reviewed with documented source gaps: the separate Carburetors handbook, supplied 4137 120 0602 installation sheet, and exact contemporaneous owner/shop-manual fuel guidance were not identified in the bounded retained corpus. Later 2004/2005 component-manual fuel evidence is separately dated and model-limited; it does not recover the 1999 editions or establish HL 75 K coverage. TI41/1997 is checked only within its named-model scope. This historical evidence is not a complete conversion procedure, physical interchange proof or authorization to run or adjust hardware.

Source: TI 21/1999, p. 1 · TI 21/1999, p. 3 · TI 21/1999, p. 4 · TI 21/1999, p. 6 · TI 21/1999, p. 7 · TI 21/1999, p. 8 — 1.4 shroud diagrams and insert; 1.5.1 compatibility exception; summary items 22–23 and remarks 4–5.

Part numbers (2)
  • 4137 080 1600 — Shroud, originalOriginal no longer available from factory · Historical summary item 22, remark 4
  • 4137 080 1601 — Shroud, new with insertAssembly including item 23 · Original and new machine/carburetor versions; insert not separately available

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →