← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section H · 8 of 25 · 31 parts

Carburetor C1Q-S56A (16.2001)

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202123242526272829330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 4226 120 7100 Throttle shaft with lever 1
2 1123 122 3000 Spring 1
3 4137 121 3300 Throttle shutter 1
4 1125 122 7403 Round head screw 1
5 1125 122 9001 E-clip 1
6 4137 121 8900 Pin → replaced by 4128 121 8900 TI 41/1997 1
7 1120 122 9000 E-clip 1
8 1129 121 4800 Pump diaphragm 1
9 1123 129 0905 Gasket 1
10 4128 121 0800 End cover → replaced by 1130 121 0801 TI 31/2009 1
11 1120 122 7800 Oval head screw 1
12 4116 121 5100 Inlet needle 1
13 1123 122 3001 Spring 1
14 1125 121 5000 Inlet control lever 1
15 1120 121 9200 Spindle 1
16 1120 122 6600 Collar screw 1
17 4129 129 0902 Gasket Fitment / change note → 1
18 4129 121 4700 Metering diaphragm Fitment / change note → 1
19 4140 120 2250 Flange Fitment / change note → 1
20 4226 122 7100 Screw Fitment / change note → 4
21 4137 122 6300 Idle speed adjustment screw 1
23 1123 121 7800 Strainer 1
24 4137 122 5100 Outlet valve 1
25 4137 121 5601 Fixed jet 0.42 1
26 4119 121 0700 Cup plug 1
27 4129 121 0700 Cup plug 1
28 not sold separately End cover not available as a separate item 1
29 4226 121 2700 Cap 1
30 4137 121 8600 Washer 1
Not numbered on the diagram — assemblies, kits and options
— 4137 120 0604 Carburetor C1Q-S56A Fitment / change note → 1
— 4227 007 1060 Set of carburetor parts 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T

4137 LD carburetors: four-screw primer flange kit

C1Q-S56 replaces C1Q-S45 for previous machines; the flange kit is not the new-cylinder carburetor.

  • The two-screw end cover can distort the primer flange and metering diaphragm. The revised end cover and flange use four screws. On previous carburetors, exchange flange and cover together with the two additional longer screws; do not change only one component.
  • Unresolved screw-number conflict: page 3 prose specifies 4226 121 7100; page 4 summary item 9 specifies 4226 122 7100, quantity increased from two to four. Both original scans agree with their respective text. Neither number is silently corrected or certified as the right screw.
  • Page 3 drawing identifies A screws, B/B1 old/new end cover, C/C1 old/new flange, D metering diaphragm and E gasket. Kit comprises A, B1, C1, D, E. Page 4 instructs finger-tight insertion, then alternate diagonal tightening. No torque is stated; separately supplied kit installation instructions are referenced but were not located in the retained STIHL service documentation document index/resources or supplemental manual PDFs. Later workshop flange sections are not the exact kit instructions; this remains a documented source gap.
  • Common unchanged diaphragm 4129 121 4700 and gasket 4129 129 0902 remain listed. Previous two-screw item 8 is 1128 122 7100; item 9 is 4226 122 7100. Old end cover 4226 121 0800 remains a spare for other models; the new end cover and flange are not separate supply items. Summary asterisks/dashes are not new order numbers.
  • For the twelve cover models, two-screw C1Q-S45, 4137 120 0603 (includes items 4–9), is replaced by four-screw C1Q-S56, 4137 120 0604 (includes kit item 3). The former is supplied only while stocks last. Both are old-generation BIS/LD carburetors, not replacements for the new-cylinder C1Q-S63.
  • Flange kit 4140 120 2250 contains summary items 4–7 and 9; previous flange 4226 120 2200 is replaced by this kit. The new flange applies as spare to Zama C1Q carburetors with LD screw, within each model-specific kit assignment, not every C1Q regardless of version.
  • Page 7 older-machine serial 2 49 848 196 conflicts with page 2 FS 85 introduction 2 49 849 196; this record does not manufacture a clean serial boundary.
  • Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.

Source: TI 16/2001, p. 1 · TI 16/2001, p. 3 · TI 16/2001, p. 4 · TI 16/2001, p. 5 · TI 16/2001, p. 7 — Sections 3.1–3.1.5 and 3.2.5: primary-model flange replacement, drawing, every common row and remarks.

Part numbers (10)
  • 4137 120 0603 — Carburetor C1Q-S45, two screwsPrevious BIS/LD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 120 0604 — Carburetor C1Q-S56, four screwsReplacement BIS/LD · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4140 120 2250 — Flange kitItems 4–7 and 9 · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4226 120 2200 — Previous primer flangeUse flange kit · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4226 121 0800 — Previous end coverRemains for other models; new cover not separate · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4129 121 4700 — Metering diaphragmUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4129 129 0902 — GasketUnchanged · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 1128 122 7100 — Previous screw, item 8Two in old arrangement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4226 122 7100 — Screw, summary item 9Four in new arrangement; conflicts with prose · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4226 121 7100 — Longer screw as printed in proseUnresolved conflict with summary · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →