← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section G · 7 of 25 · 37 parts

Carburetor C1Q-S63A, C1Q-S78 BR (15.2003)

Fits FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252627282933031323334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (37)

PosPart numberDescriptionQty
1 4137 120 7100 Throttle shaft with lever 1
2 1123 122 3000 Spring 1
3 4128 121 8900 Pin 1
4 4137 121 8600 Washer 1
5 1120 122 9000 E-clip 1
6 4229 121 3303 Throttle shutter 1
7 1125 122 7403 Round head screw 1
8 1125 122 9001 E-clip 1
9 1129 121 4800 Pump diaphragm 1
10 1123 129 0905 Gasket 1
11 1123 121 0800 End cover 1
12 1120 122 7800 Oval head screw 1
13 4116 121 5100 Inlet needle 1
14 1120 122 3004 Spring 1
15 1125 121 5000 Inlet control lever 1
16 1120 121 9200 Spindle 1
17 1120 122 6600 Collar screw 1
18 1129 129 0900 Gasket → replaced by 4134 121 4700 TI 16/2009 1
19 4129 121 4700 Metering diaphragm 1
20 4140 120 2200 Flange 1
21 4226 122 7100 Screw 4
22 4229 122 6700 High speed adjustment screw 1
23 4229 122 6800 Low speed adjustment screw 1
24 1123 121 7800 Strainer 1
25 4140 121 0800 End cover 1
26 4226 121 2700 Cap 1
27 4229 122 6200 Idle speed adjustment screw 1
28 1125 122 4200 Clamp 1
29 4229 121 2700 Cap 1
30 4137 121 5603 Fixed jet 0.34 1
31 4229 121 5800 Pump piston 1
32 4140 122 3600 Sealing ring → replaced by 4314 122 3600 TI 20/2008 1
33 4229 122 3001 Spring 1
34 1120 121 7801 Strainer 1
Not numbered on the diagram — assemblies, kits and options
— 4137 120 0606 Carburetor C1Q-S63A Fitment / change note → 1
— 4137 120 0609 Carburetor C1Q-S78 no longer available from factory 1
— 1129 007 1062 Set of carburetor parts → replaced by 4128 007 1060, 4128 007 1060 TI 6/2009 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · FH 75 / HL 75 / HL 75 K / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / FS 75 / FS 80 / FS 85 / FS 85 T

C1Q-S63: limiter cap and historical service settings

The new matched-cylinder carburetor has a 270° H adjustment range; removed caps must not be reused.

  • C1Q-S63, 4137 120 0606, is only the new-cylinder 4137 020 1202 configuration. C1Q-S45 and C1Q-S56 remain previous BIS/LD versions. Keep the page 2/page 7 serial conflict explicit; no common cutoff is asserted.
  • Illustration identifies low-speed screw 1, high-speed screw 2, H limiter cap 3 and body stop pin 4. The cap pushes over the H screw head onto knurling; the body stop restricts adjustment to 270° (3/4 turn). Funnel-shaped cap interiors aid screwdriver insertion.
  • For shop replacement of a damaged H screw or carburetor cleaning, pull the cap off with suitable pliers. Do not reuse removed caps because removal may damage them. Before adjustment inspect air filter, spark-arresting screen and fuel filter; clean or replace as necessary.
  • Historical standard setting with H limiter cap removed: from lightly seated, open H 1½ turns. Install a NEW cap aligned to the rich stop and press fully home against the carburetor body. The illustration is the alignment reference; this is not permission to defeat a limiter.
  • From lightly seated, open L one full turn counterclockwise. Use LA to set 2800 RPM and check with a tachometer; verify smooth acceleration through repeated throttle opening and smooth idle. These source settings apply to this stated configuration, not every 4137 or C1Q carburetor. No hardware adjustment was performed.
  • User H adjustment is limited to 270° for conditions such as altitude or changing nylon-line/metal cutting tools. The TI refers the complete user procedure to the model owner manual, Adjusting the Carburetor. The exact owner-manual edition was not located in the retained inventory. Later workshop manuals have user-adjustment sections, but are not established as the referenced owner instructions. This is a documented source gap; this note is not the complete user procedure.
  • Only explicitly named models and configurations are covered. Shared IPL pages do not extend these assertions to unnamed R/RX or other variants. Availability statements describe 2001 factory support, not present stock. The printed cover places FH/HL under 4230, HT under 4138 and KW under 4602; retained exact-model engine sheets use 4137 as navigation, not proof of series equivalence.

Source: TI 16/2001, p. 5 · TI 16/2001, p. 6 · TI 16/2001, p. 7 — Sections 3.2–3.2.5: construction, cap handling, all service settings and summary.

Part numbers (4)
  • 4137 120 0606 — Carburetor C1Q-S63New-generation matched configuration · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 020 1202 — Cylinder and pistonRequired matched cylinder · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 120 0603 — Carburetor C1Q-S45Older BIS generation · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only
  • 4137 120 0604 — Carburetor C1Q-S56Older BIS replacement · FH 75, HL 75, HL 75 K, HT 70, HT 75, FC 75, FC 85, KW 85, FS 75, FS 80, FS 85, FS 85 T; named configuration only

Wrong number or missing part for the FS 75, FS 80, FS 80 R, FS 85, FS 85 R, FS 85 T, FS 85 RX? Report a correction →