Stihl 4137 · Section V · 19 of 25 · 17 parts
Drive tube assembly FS 80, 80 R, 85, 85 R, 85 RX
Fits FS 80.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (17)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 710 7108 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 2 | 4137 710 7100 | Drive tube assembly Ø 25.4 mm / 1'' Fitment / change note → | 1 |
| 3 | 4137 710 7132 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 4 | 4137 710 7118 | Drive tube assembly Ø 25.4 mm / 1'' Fitment / change note → | 1 |
| 5 | 4137 711 7300 | Flexible liner 1455 mm / 57 5/16'' Fitment / change note → | 1 |
| 6 | 4134 711 7301 | Flexible liner 1440 mm / 56 3/4'' Fitment / change note → | 1 |
| 8 | 4137 711 2101 | Plug | 2 |
| 9 | 4137 711 3202 | Drive shaft | 1 |
| 10 | 4137 711 3200 | Drive shaft Fitment / change note → → replaced by 4137 711 3202 TI 11/2005 | 1 |
| 11 | 4137 710 3202 | Drive shaft Fitment / change note → → replaced by 4137 711 3202 TI 10/2011 | 1 |
| 12 | 4119 182 2110 | Support | 2 |
| 13 | 4140 007 1006 | Hose clamp kit | 1 |
| 14 | 9022 341 1270 | Spline screw IS-M6x14 | 1 |
| 15 | 0000 967 3725 | Warning pictogram FS | 1 |
| 16 | 0000 967 3684 | Warning pictogram FS | 1 |
| 17 | 0000 711 2500 | Sleeve | 1 |
| 18 | 0781 120 1110 | Gear lubricant 225 g Fitment / change note → option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · FS 85 / FS 85 R
FS 85/85R: hollow shaft requires matching liner
The larger lightweight shaft and revised bearing tube are a pair; relubricate after drive-tube-area repairs.
- Section 9 expressly includes FS 85 bike-handle and FS 85 R loop-handle models. The old rigid solid shaft is 6 mm (0.236 inch); the new rigid hollow shaft is 8 mm (0.315 inch). The vendor reports about 1/2 lb (0.2 kg) lower machine weight, not a measured result here. FS 85 T and FS 85 RX are not included by inference.
- A new drive shaft can only be installed in a previous version together with the new bearing tube (previously called flexible liner). Shaft changes from 4137 711 3200 to 4137 710 3202; bearing tube from 4137 711 7300 to 4134 711 7301. Keep these printed series digits, not a normalized guess.
- The USA drive-tube assembly changes from 4137 710 7100 to 4137 710 7118, includes the bearing tube, and otherwise retains the included parts. Previous drive tube and liner remain available for FS 80 (series 4137) and other models; old shaft remains available for previous model versions. This is not proof the new shaft fits those other models.
- Introduction refers to chapter 1. Retain its FS 85 serial 2 49 849 196 alongside the TI’s different 2 49 848 196 BIS/ignition statement; no universal cutoff or separate FS 85 R serial is inferred.
- Section 10 requires lubrication or relubrication after workshop repairs in the drive-tube area. STIHL recommends only its gear lubricant for hedge trimmers on the drive shaft and inside the bearing tube: 0781 120 1109, 3 oz (80 g), or 0781 120 1110, 8 oz (225 g). No amount to apply or lubrication interval is specified. These are package sizes, not application doses. No hardware work performed.
- Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.
Source: TI 16/2001, p. 13 · TI 16/2001, p. 14 — Sections 9–10: complete shaft/liner summary, drawing and workshop lubrication.
Part numbers (8)
- 4137 710 7100 — USA drive-tube assemblyPrevious · FS 85, FS 85 R; named configuration only
- 4137 710 7118 — USA drive-tube assemblyNew; includes liner · FS 85, FS 85 R; named configuration only
- 4137 711 7300 — Bearing tube / flexible linerPrevious · FS 85, FS 85 R; named configuration only
- 4134 711 7301 — Bearing tube / flexible linerRequired with new shaft · FS 85, FS 85 R; named configuration only
- 4137 711 3200 — Rigid solid drive shaftPrevious · FS 85, FS 85 R; named configuration only
- 4137 710 3202 — Rigid hollow drive shaftNew; matching liner required · FS 85, FS 85 R; named configuration only
- 0781 120 1109 — Hedge-trimmer gear lubricant, 3 oz /80 gLubricant package · FS 85, FS 85 R; named configuration only
- 0781 120 1110 — Hedge-trimmer gear lubricant, 8 oz /225 gLubricant package · FS 85, FS 85 R; named configuration only
Service note · FS 75 / FS 80 / FS 80 R / FS 85 / FS 85 R
FS 75 / 80 / 85: shaft construction, thread direction and gear ratio
FS 75 has M12 right-hand mounting; FS 80/85 use M10 × 1 left-hand. FS 80/85 gear ratio changes from 1:1.33 to 1:1.4 without a printed cutoff.
- FS 75 and FS 80 have FLEXIBLE drive shafts; FS 85 has a RIGID shaft. All are supported in a protective tube. Do not assume that a straight drive tube proves a rigid shaft or apply the later shared-sheet FS 85 T/RX entries to this introduction.
- Figure 392TI003: FS 75 output shaft (4), described as on FS 72, has M12 RIGHT-HAND thread; no pitch is printed. FS 80/85 output shaft (3), described as on FS 74/76/86/88/106/108, has M10 × 1 LEFT-HAND thread. The named mounting similarity is not permission to fit every cutting tool used on those models.
- FS 80/85 gearhead ratio is 1:1.33 at start of production, later 1:1.4. No serial, date or gearhead/pinion order number maps these two ratios. The later X and Y IPL gearheads are not silently assigned to either ratio.
- Rated maximum OUTPUT SHAFT speed: FS 75 8,500 rpm; FS 80/85 7,500 rpm, explicitly WITH 1:1.4 gear ratio. Do not transfer the 7,500 value to the initial 1:1.33 gearhead or confuse output-shaft speed with engine cut-off speed.
- Scope is the 1996 series 4137 introduction, including depicted R and RB handle arrangements. No scope is inherited by FS 85 T/RX, FC/FR/HL/HT/KM/KW/SP models or later same-named machines from a shared IPL sheet. Historical source guidance, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 36/1996, p. 3 · TI 36/1996, p. 4 — FS 75 / 80 / 85: shaft construction, thread direction and gear ratio.
No additional parts-table entry added.
Wrong number or missing part for the FS 80? Report a correction →