Stihl 4137 · Section N · 12 of 22 · 24 parts
Gear head 0°
Fits HL 75, HL 75 K.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4230 640 0504 NLA | Gear housing | 1 |
| 2 | 0000 953 1001 | Stud | 1 |
| 3 | 4119 713 6500 | Screw plug | 2 |
| 4 | 9022 341 1300 | Spline screw IS-M6x20 | 2 |
| 5 | 9513 003 1570 | Needle cage 6x10x9 | 2 |
| 6 | 4230 640 7307 NLA | Set of pinions | 1 |
| 7 | 9455 621 0750 | Circlip 9x1 | 1 |
| 8 | 9503 003 9850 | Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 | 1 |
| 9 | 9503 003 9856 | Grooved ball bearing 609-Z | 1 |
| 10 | not sold separately | Grooved ball bearing 6001-2RS not available as a separate item | 2 |
| 11 | not sold separately | Spur gear not available as a separate item | 1 |
| 12 | 0000 951 1100 | Screw IS-D5x20 | 1 |
| 13 | 0000 958 0520 | Washer | 1 |
| 14 | 4230 649 0304 NLA | Gasket | 1 |
| 15 | 4230 640 7503 | Spur gear | 1 |
| 16 | 4230 640 6800 | Connecting rod | 2 |
| 17 | 4230 642 4801 | Thrust plate | 2 |
| 18 | 4230 649 0305 | Gasket | 1 |
| 19 | 4230 640 5803 NLA | Gearbox cover | 1 |
| 20 | 9381 651 2062 | Cylindrical pin 4x10 | 2 |
| 21 | 9022 313 0680 | Spline screw IS-M4x16 | 6 |
| 22 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 23 | 0000 967 3730 | Warning pictogram | 1 |
| 24 | 0781 120 1109 | Gear lubricant 80 g option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HL 75 K / HL 75
HL 75 K / HL 75: shared assemblies and modified interfaces
FS powerhead ancestry does not establish a complete interchangeable gearhead.
- Cover and section1 identify the SAME powerhead as FS75,80,85 brushcutters; section1 names engine, shaft, control handle and loop handle as shared assemblies. No component part numbers, revision/serial limits or retrofit instructions are supplied.
- GEARHEAD: construction as in FS80,85, BUT with a connecting flange ADAPTED for the cutting-blade drive. CUTTING-BLADE DRIVE: construction as in HS75,80,85, BUT with MODIFIED connecting flange AND housing. Keep gearhead and blade drive distinct. The broad cover mention of borrowed assemblies does not erase these explicit interface differences.
- Specifications are generally referred to FS75,80,85 with listed differences. The exact original 1996 base specifications were not identified in the retained inventory; this is a documented source gap. Later 2004 powerhead and fuel-system references were reviewed separately, not silently transferred to the introduced machines. No universal compatibility is established.
- Historical TI41/1996 applies to the introduced HL 75 K straight 0° and HL 75 fixed 30° versions, printed series4230. Exact-model navigation is under later catalog series4137; this is not proof that series identifiers or later adjustable versions are equivalent. No serial cutoff or current availability is established. No hardware operation was performed.
Source: TI 41/1996, p. 1 · TI 41/1996, p. 2 — HL 75 K / HL 75: shared assemblies and modified interfaces.
No additional parts-table entry added.
Service note · HL 75 K / HL 75
HL 75 K / HL 75: five cutting-drive tightening torques
Gear cover3.5Nm; four specified blade/drive joints9.5Nm.
- Section6.1 gives five separate fastener/component assignments. SPLINE SCREW IS-M4x16: GEAR COVER/GEAR HOUSING,3.5Nm (2.6lbf.ft). NUT M5: BLADE,9.5Nm (7.0lbf.ft). SPLINE SCREW IS-M5x20: BLADE GUIDE/GEAR HOUSING,9.5Nm (7.0lbf.ft). SPLINE SCREW IS-M5x20: GEARHEAD/GEAR HOUSING,9.5Nm (7.0lbf.ft). SCREW PLUG M11x10: CUTTING BLADE DRIVE,9.5Nm (7.0lbf.ft).
- The two IS-M5x20 rows refer to different joints; neither may be collapsed into a universal M5 torque. The printed M11x10 screw-plug designation is retained without inventing a thread pitch or correcting it to a common size. No fastener ordering numbers, lubricant, locking agent or tightening sequence are printed.
- These are the listed 1996 DIFFERENCES from FS75,80,85 servicing data, not a full machine torque table. Later0°/30°/0–90° and135° assemblies are not automatically covered. Relevant later base-manual settings and test procedures are now separately reviewed; the exact original 1996 configuration remains a documented source gap.
- Historical TI41/1996 applies to the introduced HL 75 K straight 0° and HL 75 fixed 30° versions, printed series4230. Exact-model navigation is under later catalog series4137; this is not proof that series identifiers or later adjustable versions are equivalent. No serial cutoff or current availability is established. No hardware operation was performed.
Source: TI 41/1996, p. 3 — HL 75 K / HL 75: five cutting-drive tightening torques.
No additional parts-table entry added.
Wrong number or missing part for the HL 75, HL 75 K? Report a correction →