← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section P · 14 of 22 · 21 parts

Angle drive 30° (24.2005)

Fits HL 75, HL 75 K.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192334405677889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (21)

PosPart numberDescriptionQty
1 4230 640 0556 Gear housing 1
2 4230 640 0555 Gear housing 1
3 9503 003 9850 Grooved ball bearing 609 → replaced by 9503 003 9853 TI 46/2000 2
4 9503 003 9853 Grooved ball bearing 609-2Z 1
5 4230 642 0605 Drive shaft 1
6 9503 003 0100 Grooved ball bearing 6000 1
7 9503 003 9853 Grooved ball bearing 609-2Z 2
8 4130 640 7301 Set of pinions 1
9 4230 642 0606 Drive shaft 1
10 9455 621 0750 Circlip 9x1 1
11 9456 621 2660 Circlip 24x1.2 1
12 9503 003 5190 Grooved ball bearing 6001-2RS Fitment / change note → 1
13 9456 621 3100 Circlip 28x1.2 1
14 4226 641 6500 Screw plug 1
15 4230 642 0405 Drive pinion 1
16 9455 621 0850 Circlip 10x1 1
17 9022 341 1300 Spline screw IS-M6x20 2
18 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 4
19 0781 120 1109 Gear lubricant 80 g option 1
40 9022 341 1020 NLA Spline screw IS-M5x20 2
Not numbered on the diagram — assemblies, kits and options
— 4230 640 0105 Gearhead 30° 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HL 75

HL 75: three bearings also replace fixed-30° parts

Only items 4, 14 and 15 carry the bearing replacement remark for the 30° gearbox.

  • Remark 1 applies to 6001 2RS bearing 9503 003 5190 (item 4), 609 bearing 9503 003 0040 (item 14), and 609 Z bearing 9503 003 9854 (item 15). Each is also to be used as a replacement for the gearbox of the fixed 30° version.
  • This remark is not permission to install the entire adjustable gearbox, pinion set, quadrant or sleeve in a fixed head. It supplies no original bearing numbers or reverse-interchange assertion.
  • The later 30° catalog lists different 609-family numbers, including 9850 and 9853; this historical remark does not collapse 609, 609 Z and 609-2Z into universal equivalents. Keep exact source numbers and bearing designations.
  • Historical TI 44/1998 names HL 75, series 4230. Notes are located on later HL 75/HL 75 K sheets under series 4137, but do not extend the TI to HL 75 K, FH, HL-KM or later 135° heads. Introduction is in progress; no serial cutoff or current stock is established.

Source: TI 44/1998, p. 2 · TI 44/1998, p. 3 — Item-specific remark 1 on rows 4,14,15; full remarks block.

Part numbers (3)
  • 9503 003 5190 — Ball bearing 6001 2RSRemark 1: also replacement for fixed 30° gearbox · HL 75; exact 1998 variant and remark scope only
  • 9503 003 0040 — Ball bearing 609Remark 1: also replacement for fixed 30° gearbox · HL 75; exact 1998 variant and remark scope only
  • 9503 003 9854 — Ball bearing 609 ZRemark 1: also replacement for fixed 30° gearbox · HL 75; exact 1998 variant and remark scope only

Wrong number or missing part for the HL 75, HL 75 K? Report a correction →