← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section W · 21 of 22 · 18 parts

Blade, Tools

Fits HL 75, HL 75 K.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415162233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (18)

PosPart numberDescriptionQty
1 4230 704 3500 Guide 500 mm / 20" 1
2 4230 710 6053 Blade 500 mm / 20" 1
3 4226 713 6600 Pin 2
4 4226 648 6701 Slider 7
5 4230 713 1715 Flat spring 1
6 4230 740 6500 Guide 500 mm / 20" 1
7 9220 263 0702 Hexagon nut M5 5
8 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
9 4230 790 9200 Blade guard 1
10 4230 790 9800 NLA Guide guard option 1
11 4230 792 9000 NLA Guide guard option 1
12 4128 890 3400 Combination wrench 1
13 0000 890 2300 NLA Screwdriver option 1
14 0000 891 0801 NLA Tool roll option 1
15 4130 710 9000 Harness option 1
16 0000 884 0307 Safety glasses option 1
Not numbered on the diagram — assemblies, kits and options
— 4230 710 5900 Cutter bar assy. 500 mm / 20'' 1
— 4230 007 1005 NLA Guide guard kit option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · HL 75 K / HL 75

HL 75 K / HL 75: 45° blade sharpening and flat file

550mm double-edged blade; sharpening file0814 252 3356.

  • Section3: cutting blade length550mm (21.6in), double-edged, sharpening angle45°. The45° is the blade SHARPENING angle, not a machine-head angle; the introduced heads are straight0° and fixed30°.
  • Section4 assigns FLAT SHARPENING FILE0814 252 3356 to resharpening the cutting blade. No file dimensions, replacement blade number, sharpening stroke count, edge-removal limit or blade-adjustment procedure are printed. The later Blade, Tools sheet is navigation for the exact model family, not proof that all later blade lengths inherit this specification.
  • Historical TI41/1996 applies to the introduced HL 75 K straight 0° and HL 75 fixed 30° versions, printed series4230. Exact-model navigation is under later catalog series4137; this is not proof that series identifiers or later adjustable versions are equivalent. No serial cutoff or current availability is established. No hardware operation was performed.

Source: TI 41/1996, p. 1 · TI 41/1996, p. 3 — HL 75 K / HL 75: 45° blade sharpening and flat file.

Part numbers (1)
  • 0814 252 3356 — Flat sharpening fileUser accessory for resharpening · Introduced HL 75 K / HL 75 cutting blade per TI41/1996

Service note · HL 75 K / HL 75

HL 75 K / HL 75: five cutting-drive tightening torques

Gear cover3.5Nm; four specified blade/drive joints9.5Nm.

  • Section6.1 gives five separate fastener/component assignments. SPLINE SCREW IS-M4x16: GEAR COVER/GEAR HOUSING,3.5Nm (2.6lbf.ft). NUT M5: BLADE,9.5Nm (7.0lbf.ft). SPLINE SCREW IS-M5x20: BLADE GUIDE/GEAR HOUSING,9.5Nm (7.0lbf.ft). SPLINE SCREW IS-M5x20: GEARHEAD/GEAR HOUSING,9.5Nm (7.0lbf.ft). SCREW PLUG M11x10: CUTTING BLADE DRIVE,9.5Nm (7.0lbf.ft).
  • The two IS-M5x20 rows refer to different joints; neither may be collapsed into a universal M5 torque. The printed M11x10 screw-plug designation is retained without inventing a thread pitch or correcting it to a common size. No fastener ordering numbers, lubricant, locking agent or tightening sequence are printed.
  • These are the listed 1996 DIFFERENCES from FS75,80,85 servicing data, not a full machine torque table. Later0°/30°/0–90° and135° assemblies are not automatically covered. Relevant later base-manual settings and test procedures are now separately reviewed; the exact original 1996 configuration remains a documented source gap.
  • Historical TI41/1996 applies to the introduced HL 75 K straight 0° and HL 75 fixed 30° versions, printed series4230. Exact-model navigation is under later catalog series4137; this is not proof that series identifiers or later adjustable versions are equivalent. No serial cutoff or current availability is established. No hardware operation was performed.

Source: TI 41/1996, p. 3 — HL 75 K / HL 75: five cutting-drive tightening torques.

No additional parts-table entry added.

Wrong number or missing part for the HL 75, HL 75 K? Report a correction →