Stihl 4137 · Section V · 20 of 22 · 19 parts
Drive tube assembly
Fits HL 75, HL 75 K.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (19)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4230 710 7103 | Drive tube assembly Ø 25.4 mm / 1" | 1 |
| 2 | 4230 710 7101 | Drive tube assembly Ø 25.4 mm / 1" | 1 |
| 3 | 4137 711 7300 | Flexible liner 1455 mm / 57 5/16'' | 1 |
| 4 | 4137 711 2101 | Plug | 2 |
| 5 | 0000 967 3728 | Warning pictogram HL | 1 |
| 6 | 0000 967 3739 | Warning pictogram HL | 1 |
| 7 | 4230 791 2001 | Handle hose 270 mm / 10 5/8'' | 1 |
| 8 | 4137 711 3200 | Drive shaft → replaced by 4137 711 3202 TI 11/2005 | 1 |
| 9 | 4230 790 8801 | Loop | 1 |
| 10 | 0000 951 1104 | Screw IS-M5x22 | 1 |
| 11 | 4230 710 7128 | Drive tube assembly Ø 25.4 mm / 1" | 1 |
| 12 | 4230 710 7102 | Drive tube assembly Ø 25.4 mm / 1" | 1 |
| 13 | 4230 710 7100 | Drive tube assembly Ø 25.4 mm / 1" | 1 |
| 14 | 4230 711 7300 | Flexible liner 1027 mm / 40 7/16'' | 1 |
| 15 | 4230 711 3200 | Drive shaft | 1 |
| 16 | 4230 791 2002 | Handle hose 230 mm / 9'' | 1 |
| 17 | 4230 791 2000 NLA | Handle hose 185 mm / 7 5/16'' → replaced by 4230 791 2002 TI 24/2005 | 1 |
| 18 | 0000 967 7203 | Warning pictogram HL | 1 |
| 19 | 0000 711 2500 | Sleeve | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HL 75 K / HL 75
HL 75 K / HL 75: straight and fixed-angle introduction
0° / 30° versions, approximate lengths, weights and 0.9kW engine output.
- The new long-reach hedge trimmers supplement a conventional hedge trimmer for grounds maintenance. The cover photograph shows the two complete units; it supplies no ordering numbers, scale dimensions or extra variant specification.
- HL 75 K: STRAIGHT 0° cutting blades in line with the drive shaft; overall length APPROXIMATELY200cm (79in), weight6.1kg (13.4lb). HL 75: blades FIXED at30° to the drive shaft; overall length APPROXIMATELY240cm (94in), weight6.3kg (13.9lb). These are overall lengths, not shaft lengths or cutting reach. No fuel/blade-cover weighing condition is printed.
- The introduced units have engine output0.9kW (1.2bhp). No displacement, rated-speed condition or vibration value is printed here. Relative low weight and convenience are qualitative source descriptions, not measured ergonomic comparisons.
- Reciprocating, double-edged cutting blades are550mm (21.6in) long and cut in both directions. This is blade length, not the overall machine length. The fixed30° angle is not the45° sharpening angle.
- Historical TI41/1996 applies to the introduced HL 75 K straight 0° and HL 75 fixed 30° versions, printed series4230. Exact-model navigation is under later catalog series4137; this is not proof that series identifiers or later adjustable versions are equivalent. No serial cutoff or current availability is established. No hardware operation was performed.
Source: TI 41/1996, p. 1 · TI 41/1996, p. 2 · TI 41/1996, p. 3 — HL 75 K / HL 75: straight and fixed-angle introduction.
No additional parts-table entry added.
Service note · HL 75 K / HL 75
HL 75 K / HL 75: historical sound measurements
91dB(A) pressure for both; 103/104dB(A) power with equal-duration operating conditions.
- HL 75 K (0°): sound PRESSURE level Lpeq91dB(A) to ISO7917; sound POWER level Lweq103dB(A) to ISO10884. HL 75 (30°): Lpeq91dB(A) and Lweq104dB(A), respectively. The second measurement is sound power, not another operator-position pressure value.
- The footnote includes IDLING, FULL LOAD and FULL THROTTLE/NO LOAD with the SAME DURATION of exposure. Do not interpret the numbers as idle-only, peak, daily exposure allowance or modern guaranteed sound-power labeling. The TI does not print measurement uncertainty or a hearing-protection threshold.
- Historical TI41/1996 applies to the introduced HL 75 K straight 0° and HL 75 fixed 30° versions, printed series4230. Exact-model navigation is under later catalog series4137; this is not proof that series identifiers or later adjustable versions are equivalent. No serial cutoff or current availability is established. No hardware operation was performed.
Source: TI 41/1996, p. 2 — HL 75 K / HL 75: historical sound measurements.
No additional parts-table entry added.
Conditional replacement · HL 75
HL 75: swiveling carrying eye replaces steel clamp
Carrying eye 4230 790 8800 includes its M5x23 screw; the old clamp and M6x14 screw remain for other models.
- The original steel clamp 4130 710 6700 is replaced on HL 75 by swiveling eye 4230 790 8800. Figure 389TI007 KN points to the steel insert and labels eye 1 and screw 2. Strong and hard-wearing are qualitative source descriptions, not a measured load rating.
- The eye includes spline screw IS M5x23, 9022 313 1030. The old clamp includes spline screw IS M6x14, 9022 341 1270. Both old rows carry remark 1: original versions remain available for other models. A dash in the new column does not mean the old screw fits the new eye.
- The note expressly permits replacing this original clamp on other models with the new carrying eye, but does not name those models. The relationship is conditional on the exact old clamp, not a blanket series-wide retrofit; no new model list is invented.
- The later HL 75 drive-tube sheet lists eye 4230 790 8801 and screw IS-M5x22, 0000 951 1104. These are not equated with the 1998 eye/screw. No clamp torque or chronological successor relationship is established by this TI. Last-TI 41.96 and footer 6411 are bibliographic, not further fitment assertions.
- Historical TI 44/1998 names HL 75, series 4230. Notes are located on later HL 75/HL 75 K sheets under series 4137, but do not extend the TI to HL 75 K, FH, HL-KM or later 135° heads. Introduction is in progress; no serial cutoff or current stock is established.
Source: TI 44/1998, p. 4 — Complete section 3, steel-insert figure, all four table rows, remark and footer.
Part numbers (4)
- 4130 710 6700 — Original steel clampIncludes old M6x14 screw; remains for other models · HL 75; exact 1998 variant and remark scope only
- 4230 790 8800 — Swiveling carrying eye with steel insertIncludes new M5x23 screw · HL 75; exact 1998 variant and remark scope only
- 9022 313 1030 — Spline screw IS M5x23New eye companion · HL 75; exact 1998 variant and remark scope only
- 9022 341 1270 — Spline screw IS M6x14Old clamp companion; retained for other models · HL 75; exact 1998 variant and remark scope only
Wrong number or missing part for the HL 75, HL 75 K? Report a correction →