← Special-purpose Units & other equipment · series 4137

Stihl 4137 · Section S · 17 of 24 · 22 parts

Gear head

Fits HT 70, HT 75.

Parts diagrams →

Historical fitment & changes (21) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011111213141414151617181922034566789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (22)

PosPart numberDescriptionQty
1 4138 641 0301 Gear housing 1
2 4138 640 3200 Oil pump 1
3 4138 640 7302 Set of pinions 1.27 1
4 9503 003 9860 Grooved ball bearing 609-2RS 1
5 9503 003 5190 Grooved ball bearing 6001-2RS 1
6 9503 003 5030 Grooved ball bearing 6000-2RS 2
7 9455 621 0850 Circlip 10x1 1
8 4138 641 0400 Gearbox cover 1
9 9022 341 1050 Spline screw IS-M5x25 8
10 4138 642 8201 Ring Fitment / change note → 1
11 1208 162 8900 Washer Fitment / change note → 2
12 4138 642 1250 Chain sprocket 3/8" Picco 6T 1
13 4138 642 1350 Chain sprocket 3/8" Picco 7T Fitment / change note → 1
14 9485 648 1694 Cup spring 28x10.2x1.25 Fitment / change note → 3
15 1208 162 4200 Collar screw Fitment / change note → 1
16 0000 953 1402 Stud M8 → replaced by 1129 664 2401 TI 20/1997 1
17 1128 640 9100 Valve 1
18 4138 353 2700 Connector 1
19 1117 647 6801 Strainer 1
20 0783 830 2000 Tube of sealant Dirko HT red option 1
Not numbered on the diagram — assemblies, kits and options
— 4138 640 0116 Gearhead 1
— 0781 120 1118 Gear lubricant 225 g Fitment / change note → not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · HT 75

HT 75: gearbox bearing order, sealant and 8 g lubricant

Preserve bearing positions, 8 g pinion-cavity fill and the staged 6.5 Nm cover/clamp sequence.

  • For friction-clutch versions, section 2.1 additionally requires TI36/1998. Its reviewed instructions remain distinct: left-hand collar screw, 6 Nm tightening, coupled sprocket/washer replacement and complete sets of three cup springs, with a separate 5–14 Nm slip-torque check. These general gearbox instructions and their 6.5 Nm cover/clamp torque do not replace that clutch procedure. The separate retrofit-kit instruction-sheet gap remains documented under TI36/1998.
  • Release gearbox clamp screws and remove gearbox from the tube. Remove sprocket cover, sprocket and oil tank; slide ring (1) off shaft (2), remove screws (3) and cover (4), and lift pinion (5) from housing (6). The friction-clutch qualification still applies to sprocket removal.
  • Use pliers 0811 611 8200 to remove retaining ring (7), then pull bearings (9) from the pinion. Remove shaft (2) from the housing and pull bearings (10,11) from it. Diagram numbers identify positions here, not order numbers.
  • Press bearing (10) onto the pinion end of shaft (2), then bearing (11), and install the shaft in the housing. Press bearings (9) onto the pinion and install retaining ring (7).
  • Fill the pinion cavity in the gearbox housing with 8 g gear lubricant, then fit the pinion. Section 3.1 specifies brushcutter gear lubricant 0781 120 1117 / 0781 120 1118. The 8 g is the stated assembly fill for that cavity, not a general maintenance interval or total oil-tank capacity.
  • Apply a thin coating of Dirko sealant 0783 830 2120 to the housing mating face. Fit the cover and tighten its screws except the arrowed clamp screws to 6.5 Nm (4.8 lbf.ft).
  • Refit ring (1). Slide the gearbox onto the tube while turning it so the square shaft end engages the drive-pinion square socket. Push to the stop and align correctly before tightening gearbox clamp screws to 6.5 Nm (4.8 lbf.ft). Do not clamp the gearbox before seating and alignment.
  • The retained later IPL lists Dirko HT red 0783 830 2000; TI14/1999 gives 0783 830 2120. This note does not establish that they are equivalents or supersessions, or apply the 1999 procedure to every later gearhead.
  • TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
  • Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.

Source: TI 14/1999, p. 4 · TI 14/1999, p. 5 · TI 14/1999, p. 6 — 2.1 and 3.1: gearbox disassembly, bearing positions, lubricant, sealant and staged tightening.

Referenced bulletin evidence: TI 36/1998, p. 1 · TI 36/1998, p. 2 · TI 36/1998, p. 3 · TI 36/1998, p. 4 — All sections 1–2: friction clutch introduction, service, parts summary and oil strainer.

Part numbers (4)
  • 0811 611 8200 — Retaining-ring pliersSpecified service tool · HT 75 configuration described in TI14/1999 only
  • 0783 830 2120 — Dirko sealantHousing mating-face sealant · HT 75 configuration described in TI14/1999 only
  • 0781 120 1117 — Brushcutter gear lubricantPinion-cavity assembly lubricant · HT 75 configuration described in TI14/1999 only
  • 0781 120 1118 — Brushcutter gear lubricantPinion-cavity assembly lubricant · HT 75 configuration described in TI14/1999 only

Service note · HT 75

HT 75: oil tank removal and oil pump slot orientation

Retain the strainer, M5 extraction screw and engine-facing pump slot; do not invent a pump torque.

  • Remove the oil filler cap with its retainer and remove the tank screws. Swing the tank counterclockwise and lift it away; installation reverses removal.
  • With the tank removed, ease rubber seal (1) out of the gearbox housing and remove filter screen (2). Screw an M5 screw at least 25 mm long (printed 1 inch) into the pump and pull it out using the screw. Clean the oil passages.
  • Align the oil pump to the symbol beside the bore: its slot must point toward the engine. Screw an M5 screw into the pump to press it home, then remove the temporary screw. Reverse the remaining removal steps for assembly.
  • The source gives no oil-pump, screen, seal or screw order number, press depth or tightening torque. The M5 screw is a temporary extraction/pressing aid, not a retained replacement component.
  • TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
  • Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.

Source: TI 14/1999, p. 5 · TI 14/1999, p. 6 — 2.2–2.3: tank removal, seal/screen, temporary M5 screw and pump orientation.

No additional parts-table entry added.

Service note · HT 75

HT 75: friction-clutch gearbox and complete retrofit kit

Production introduction from 2 39 949 387; earlier HT 75 conversion uses the complete kit, not an isolated sprocket swap.

2 39 949 387 — Friction-clutch gearbox production introduction, not a retrofit exclusion or a separate 4 mm ring cutoff.

  • The new gearbox with chain-sprocket friction clutch is introduced from serial 2 39 949 387 to reduce load on the multi-part telescopic drive shaft. A dull chain suddenly applied to a cut can cause overload; users must keep the chain sharp by regular resharpening. These are source design/user statements, not measured load or reliability results.
  • Every HT 75 can be converted, according to section 1.4.3, using all necessary parts in friction clutch kit 4138 007 1001. The production serial is not a retrofit exclusion. The separate instruction sheet supplied with that kit identifies the parts to replace; it is not reproduced in this four-page bulletin and no matching kit instruction was identified in the bounded retained docs/manual inventory. Do not turn the parts summary into an invented complete installation procedure.
  • Section 1.5 lists gearbox 4138 640 0105 → 4138 640 0106 including table items 3, 6, 7 and 10–12; kit 4138 007 1001 consists of items 3, 6, 7, 11 and 12. The listed gearbox inclusion range contains item 10 even though the new E-clip cell is deleted: retain the printed table, not an inferred requirement for an E-clip in the new clutch.
  • Pinion set 4138 640 7300 → 4138 640 7301 contains shaft and pinion (items 4 and 5), neither available separately. The 3/8 inch Picco, 7-tooth sprocket assembly 1206 642 1301 → 4138 642 1350 contains two washers and the sprocket (items 8 and 9); the new loose sprocket is not available separately and has no independent order number.
  • The two washers change from 0000 958 0506 to 1208 162 8900; E-clip 8 x 1.3, 9460 624 0801, has no new counterpart. Three cup springs 20 x 10.2 x 1.25, 9485 648 1694, and collar screw 1208 162 4200 are new. All other parts remain as before. Blank/deleted cells and not-separately-supplied symbols are not part numbers.
  • Remark 1 says the original gearbox, pinion set, ring, sprocket assembly, washers and E-clip remain available as spares. This is historical supply guidance, not current stock or unconditional individual-part interchange. The ring row also conflicts with the more specific replacement-only ring statement in section 1.4.2; that conflict is retained in the ring note.
  • The summary says modification introduction is in progress; page 1 supplies the production serial. The later 4 mm ring introduction is not given its own serial. Section 1.2 refers construction/function to TI40/1994 section 1.2 (E20 friction clutch); that retained TI is already dispositioned in the existing e20-friction-clutch-retrofit-1994 note. Its mechanism is friction-locked through three cup springs and two washers, one each side of the sprocket; this does not import E20 part numbers or service torques into HT75. Section 1.4.1 refers other repairs to TI03/1997, subsequently superseded by reviewed TI14/1999. Footer TI30/1998 is a previous-bulletin reference, not a supersession.
  • Scope is HT 75, printed series 4138. The exact-model catalog sheet is grouped under 4137 and also names HT 70; this navigation does not establish series equivalence or extend the bulletin to HT 70. These are historical source instructions, not a hardware test or confirmation of the configuration of an individual machine.

Source: TI 36/1998, p. 1 · TI 36/1998, p. 2 · TI 36/1998, p. 4 — Sections 1–1.4.3 and 1.5: introduction, dependencies, complete kit and all table rows.

Part numbers (14)
  • 4138 640 0105 — GearboxOriginal assembly; remains spare · HT 75 configuration described in TI36/1998 only
  • 4138 640 0106 — Gearbox with friction clutchNew assembly · HT 75 configuration described in TI36/1998 only
  • 4138 007 1001 — Friction clutch kitComplete retrofit kit · HT 75 configuration described in TI36/1998 only
  • 4138 640 7300 — Pinion setOriginal assembly; remains spare · HT 75 configuration described in TI36/1998 only
  • 4138 640 7301 — Pinion setNew assembly; shaft/pinion not separate · HT 75 configuration described in TI36/1998 only
  • 4138 642 8200 — RingOriginal; conflicting supply statements retained · HT 75 configuration described in TI36/1998 only
  • 4138 642 8201 — 4 mm ringNew service ring · HT 75 configuration described in TI36/1998 only
  • 1206 642 1301 — 3/8 inch Picco 7-tooth sprocket assemblyOriginal assembly; remains spare · HT 75 configuration described in TI36/1998 only
  • 4138 642 1350 — 3/8 inch Picco 7-tooth sprocket assemblyNew assembly with two washers · HT 75 configuration described in TI36/1998 only
  • 0000 958 0506 — Washer (2x)Original; remains spare · HT 75 configuration described in TI36/1998 only
  • 1208 162 8900 — Washer (2x)New; replace with sprocket · HT 75 configuration described in TI36/1998 only
  • 9460 624 0801 — E-clip 8 x 1.3Original only; remains spare · HT 75 configuration described in TI36/1998 only
  • 9485 648 1694 — Cup spring 20 x 10.2 x 1.25 (3x)New; replace as full set · HT 75 configuration described in TI36/1998 only
  • 1208 162 4200 — Collar screwNew; left-hand thread · HT 75 configuration described in TI36/1998 only

Service note · HT 75

HT 75: replace the early ring and spacer together

The 3.6 mm ring plus 0.4 mm washer is replaced by one 4 mm ring; supply statements conflict.

  • At start of friction-clutch production, drawing item 8 is a 3.6 mm ring with a separate 0.4 mm washer (drawing item 7). Both are later replaced by 4 mm ring 4138 642 8201. Do not retain the 0.4 mm washer with the 4 mm ring or infer a separate washer order number from its drawing position.
  • Only ring 4138 642 8201 is to be supplied as a replacement under section 1.4.2; it is included in kit 4138 007 1001. Even if the early ring was already replaced during repair, that ring and washer must still be replaced by the 4 mm ring.
  • The section 1.5 table separately lists original ring 4138 642 8200 → 4138 642 8201 with remark 1, original version remains available as spare. This conflicts with the replacement-only statement above. Both historical statements are retained; no current availability or unconditional interchange is inferred.
  • Drawing positions and summary-table items are different numbering systems: drawing item 7 is the 0.4 mm spacer, while table item 7 is the sprocket assembly. The 0.4 mm spacer is not silently assigned either of the two sprocket-washer part numbers. No separate production serial is supplied for the one-piece ring.
  • Scope is HT 75, printed series 4138. The exact-model catalog sheet is grouped under 4137 and also names HT 70; this navigation does not establish series equivalence or extend the bulletin to HT 70. These are historical source instructions, not a hardware test or confirmation of the configuration of an individual machine.

Source: TI 36/1998, p. 2 · TI 36/1998, p. 4 — Sections 1.4.2 and 1.5: early stack, service rule, drawing keys and supply conflict.

Part numbers (3)
  • 4138 642 8200 — Original ringTable original; supply conflict · HT 75 configuration described in TI36/1998 only
  • 4138 642 8201 — 4 mm replacement ringReplaces early ring plus spacer · HT 75 configuration described in TI36/1998 only
  • 4138 007 1001 — Friction clutch kitIncludes 4 mm ring · HT 75 configuration described in TI36/1998 only

Service note · HT 75

HT 75: left-hand collar screw and coupled sprocket service

Replace both washers with the sprocket and cup springs as a set of three; collar-screw torque is 6 Nm.

  • The collar screw centers the cup springs and has a left-hand thread. Always replace cup springs in complete sets of three. Always replace both washers along with the chain sprocket; they are supplied with the replacement sprocket.
  • A special holding tool must be purchased or made. Page 2 permits a commercial T-handle 5 mm square-section key, or a 5 mm hex-section key such as 5910 890 2410 shortened and profiled as drawn. Drawing 390TI005 KN shows a 5 mm (0.196 inch) square end, 25 mm (1 inch) modified tip length and 100 mm (4 inch) shaft length to the handle. These rounded inch labels are not alternative exact machining specifications.
  • Remove the gearbox from the drive shaft and clamp it in a vise. Insert the special tool into the gearbox shaft square socket to its stop. Unscrew the collar screw clockwise, then remove cup springs and worn sprocket while noting their installed positions. Replace damaged springs as a complete set; do not guess their orientation from a text list.
  • Fit the new sprocket and cup springs, including the required new washers, and tighten the collar screw counterclockwise to 6 Nm (4.4 lbf.ft). This fastener torque is not the 5–14 Nm clutch slip-torque acceptance range or the gearbox housing/clamp screw torque.
  • Scope is HT 75, printed series 4138. The exact-model catalog sheet is grouped under 4137 and also names HT 70; this navigation does not establish series equivalence or extend the bulletin to HT 70. These are historical source instructions, not a hardware test or confirmation of the configuration of an individual machine.

Source: TI 36/1998, p. 2 · TI 36/1998, p. 3 · TI 36/1998, p. 4 — Sections 1.4.1, 1.4.4 and 1.5: coupled replacement, tool geometry and tightening.

Part numbers (5)
  • 5910 890 2410 — 5 mm hex-section T-handle keyTool to modify as drawn · HT 75 configuration described in TI36/1998 only
  • 4138 642 1350 — Sprocket assemblyReplacement with washers · HT 75 configuration described in TI36/1998 only
  • 1208 162 8900 — Washer (2x)Replace with sprocket · HT 75 configuration described in TI36/1998 only
  • 9485 648 1694 — Cup spring (3x)Replace complete set · HT 75 configuration described in TI36/1998 only
  • 1208 162 4200 — Collar screwLeft-hand thread; 6 Nm · HT 75 configuration described in TI36/1998 only

Service note · HT 75

HT 75: clutch slip-torque check is 5–14 Nm

Lock the sprocket using the illustrated guide-bar setup; out-of-range torque requires washers, sprocket and springs.

  • A slip-torque check may be necessary after repair. Use a commercial 5 mm square-section torque-wrench bit, or modify STIHL 5 mm bit 5910 890 0102 to the profile in section 1.4.4 but do not shorten it. The shortened T-handle holding tool is not this torque-measuring bit.
  • Remove the gearbox from the shaft, clamp it by its hook in the vise and remove the complete chain tensioner. Position the guide bar against the gearbox, push it toward the sprocket and engage its upper end between two teeth as indicated in drawing 390TI007 KN.
  • Fit several A 8.4 mm washers totaling 6 mm thickness, or ring 0000 961 1409, on the stud. Tighten the nut to lock the sprocket; no nut tightening torque is specified here. These are test-fixture spacers, not the two sprocket friction washers or the early 0.4 mm spacer.
  • Check with the torque wrench: the slip reading must be between 5 and 14 Nm (3.7–10.3 lbf.ft). If outside that range, replace the washers, chain sprocket and cup springs, respecting the full set of three springs. Do not adjust the 6 Nm collar-screw torque to force a passing slip value.
  • Scope is HT 75, printed series 4138. The exact-model catalog sheet is grouped under 4137 and also names HT 70; this navigation does not establish series equivalence or extend the bulletin to HT 70. These are historical source instructions, not a hardware test or confirmation of the configuration of an individual machine.

Source: TI 36/1998, p. 2 · TI 36/1998, p. 3 — Section 1.4.5 with tool-profile reference to 1.4.4: full fixture and rejection procedure.

Part numbers (2)
  • 5910 890 0102 — 5 mm torque-wrench bitModify profile; do not shorten · HT 75 configuration described in TI36/1998 only
  • 0000 961 1409 — RingAlternative 6 mm test-fixture spacer · HT 75 configuration described in TI36/1998 only

Service note · HT 75

HT 75: clean the oil channels and pump strainer

Oil-supply trouble requires removal and cleaning of the strainer in front of the pump.

  • For trouble with the lubricating-oil supply, clean the oil channels and remove and clean the strainer in front of the oil pump. Drawing 390TI009 KN identifies pump (1) above strainer (2); these are illustration keys, not order numbers.
  • This bulletin supplies no pump or strainer part number, pressure/flow specification, cleaning interval or solvent. It does not replace the later pump-removal and slot-orientation service information in TI14/1999.
  • Scope is HT 75, printed series 4138. The exact-model catalog sheet is grouped under 4137 and also names HT 70; this navigation does not establish series equivalence or extend the bulletin to HT 70. These are historical source instructions, not a hardware test or confirmation of the configuration of an individual machine.

Source: TI 36/1998, p. 4 — Section 2: complete oil-pump/strainer instruction and illustration.

No additional parts-table entry added.

Service note · HT 75

HT 75: superseded 1997 gearbox service

Superseded by TI14/1999. Retain bearing order, 8 g gear lubricant, Dirko sealant and separate cover/clamp tightening stages.

Later reviewed guidance: HT 75: gearbox bearing order, sealant and 8 g lubricant

  • Superseded historical instruction: TI14/1999 explicitly supersedes and replaces TI03/1997. Follow the linked later source for its revised procedure; the two versions must not be blended into an invented sequence.
  • TI03/1997 restricts inspection, service and repair to trained, authorized personnel and refers to the illustrated spare-parts list for orientation. This is an offline source record, not a hardware experiment.
  • The source names only HT 75, type 4138. The exact-model IPL is filed under 4137 and also names HT 70; that navigation link does not establish series equivalence, extend this procedure to HT 70 or prove applicability to every later HT 75. No production serial is printed.
  • Loosen gearbox clamp screws and pull gearbox off protective tube. Remove sprocket cover, sprocket and oil tank (section 2.2), remove ring (1) from shaft (2), then remove screws (3) and gear cover (4). This edition does not contain the later friction-clutch procedure.
  • Remove pinion assembly (5) from housing (6). Remove circlip (7) using pliers (8), order number 0811 611 8200, and remove ball bearings (9). Remove shaft assembly (2) from housing and pull bearings (10,11) off it.
  • Press bearing (10) onto the pinion end of shaft (2), then bearing (11). Insert shaft assembly in housing; press bearing (9) into position and fit circlip (7), following the original drawings. Diagram callouts are not replacement bearing numbers.
  • Put 8 g (printed 0.3 oz) gear lubricant into the gear-housing cavity, then insert pinion (5). This 1997 edition does not give a lubricant order number; the amount is an assembly fill, not a maintenance interval or oil-tank volume.
  • Thinly coat gear-housing edge with Dirko sealant 0783 830 2120; fit cover (4) and tighten screws (3), excluding the arrowed clamp screws, to 6.5 Nm (printed 5 lbf.ft). Do not infer equivalence to a later IPL sealant number.
  • Press ring (1) onto shaft (2). Slide gearbox onto protective tube while turning it back and forth so the drive-shaft square engages the pinion socket. Push fully home and align; only then tighten gearbox clamp screws to 6.5 Nm (printed 5 lbf.ft).

Source: TI 3/1997, p. 3 · TI 3/1997, p. 4 · TI 3/1997, p. 5 — Complete2.1: gearbox disassembly, bearing order, lubricant amount, sealant and staged tightening.

Part numbers (2)
  • 0811 611 8200 — Circlip pliersSpecified service tool · HT 75; historical TI03/1997 gearbox
  • 0783 830 2120 — Dirko sealantGear-housing edge sealant · HT 75; historical TI03/1997 gearbox

Service note · HT 75

HT 75: superseded 1997 oil tank and pump service

Superseded by TI14/1999. Preserve counterclockwise tank removal and the pump groove facing the tube mount.

Later reviewed guidance: HT 75: oil tank removal and oil pump slot orientation

  • Superseded historical instruction: TI14/1999 explicitly supersedes and replaces TI03/1997. Follow the linked later source for its revised procedure; the two versions must not be blended into an invented sequence.
  • TI03/1997 restricts inspection, service and repair to trained, authorized personnel and refers to the illustrated spare-parts list for orientation. This is an offline source record, not a hardware experiment.
  • The source names only HT 75, type 4138. The exact-model IPL is filed under 4137 and also names HT 70; that navigation link does not establish series equivalence, extend this procedure to HT 70 or prove applicability to every later HT 75. No production serial is printed.
  • Remove filler cap with retainer, remove oil-tank screws and swivel tank counterclockwise to remove it. Assemble tank parts in reverse order.
  • With tank removed, pull rubber buffer (1) from the gearbox housing and remove strainer (2). Thread an M5 screw at least 25 mm long into the oil pump and pull it out by the screw. No screw, pump, strainer or buffer order number is supplied.
  • Insert oil pump according to the symbol beside the opening: the full-length groove must face the tube mount. Thread the M5 screw into the pump and press the pump home; remove the screw and assemble remaining parts in reverse order. The screw is a temporary tool, not a retained pump component; no pressing depth, force or torque is printed.

Source: TI 3/1997, p. 5 · TI 3/1997, p. 6 — Complete2.2–2.3: tank, buffer/strainer, M5 extraction/pressing aid and groove orientation.

No additional parts-table entry added.

Service note · HT 75

HT 75 introduction: 14-inch PMN and seven-tooth sprocket

Printed 14 in bar, 3/8-inch Picco-Micro-Narrow PMN chain with 44 links, and 7-tooth 3/8 P spur sprocket.

  • Page 1 calls the equipment Picco-Mini bar and chain as for the 017. Section 3 specifies bar length 14 in; Oilomatic 3/8-inch Picco-Micro-Narrow (PMN), 44 links; Rollomatic Mini guide bar; and spur chain sprocket, 7 teeth, for 3/8 P.
  • Keep the printed 14 IN / 44 LINKS combination without correcting it from the later IPL. The later exact-model oil-tank/cover sheet lists a 12-inch bar and 61PMM3 chain; the gearhead sheet lists both six- and seven-tooth sprockets. Neither later listing proves the original TI combination is correct or establishes an approved substitution.
  • The bulletin provides no bar, chain or sprocket ordering numbers, no drive-link gauge and no chain-length measurement. Do not invent them from the 017 comparison or use the source alone as an assembled-fit verification.
  • The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.

Source: TI 47/1996, p. 1 · TI 47/1996, p. 2 · TI 47/1996, p. 3 — HT 75 introduction: 14-inch PMN and seven-tooth sprocket.

No additional parts-table entry added.

Service note · HT 75

HT 75 introduction: original drive-shaft and gear grease listing

0781 120 6602, 40 g tube, is listed for both profiled drive shaft and gear; later lubricant roles remain separate.

Later reviewed guidance: HT 75: paired drive shafts and separate lubricant locations · HT 75: gearbox bearing order, sealant and 8 g lubricant

  • Section 5.2 lists GREASE (40 g tube), 0781 120 6602, for drive shaft (profiled shaft), gear, with remark NEW. The 40 g is package size, not an instruction to put 40 g into either assembly.
  • Section 1 calls the profiled shaft pre-lubricated. This TI supplies no application quantity, refill interval or gear assembly procedure.
  • Already-reviewed TI14/1999 distinguishes grease 0781 120 6602 at the plastic liner, synthetic two-stroke oil on the external splined shaft and brushcutter gear lubricant at the pinion cavity. Its different assignments must not be silently merged into this 1996 gear-grease row. TI03/1997 is explicitly superseded by TI14/1999; that does not prove every line of TI47/1996 was explicitly superseded.
  • The later IPL lists telescopic-boom grease 0781 120 6000. Neither a similar description nor the retained 1996 number establishes lubricant equivalence.
  • The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.

Source: TI 47/1996, p. 2 · TI 47/1996, p. 3 — HT 75 introduction: original drive-shaft and gear grease listing.

Referenced bulletin evidence: TI 14/1999, p. 6 — Previously accepted sections 3.1–3.3, location-specific lubricants; no new review of this lane.

Part numbers (1)
  • 0781 120 6602 — Grease, 40 g tubeOriginal drive-shaft / gear aid · HT 75 configuration described in TI47/1996 only

Service note · HT 75

HT 75 introduction: six fastening rows and M8 adhesive condition

2.5 / 3.0 / 4.5 Nm location-specific screws; M8 bar fixture uses medium-grade adhesive and 19.5 Nm.

  • Section 6.1 row 1: socket-head screw IS-DG5x12, oil tank / gear housing, 2.5 Nm (1.8 ft. lbs.). The later oil-tank IPL lists IS-D5x20 instead; do not substitute that screw or its number into this historical row.
  • Rows 2 and 3: socket-head screw IS-M5x20, clamp / LARGE protective tube and clamp / SMALL protective tube, each 3.0 Nm (2.2 ft. lbs.). Preserve both locations; this is not a general M5 torque.
  • Row 4: socket-head screw IS-M6x14, clamping collar / carrying ring, 4.5 Nm (3.3 ft. lbs.). Row 5: socket-head screw IS-M6x20, clamp / power unit / shaft, 4.5 Nm (3.3 ft. lbs.).
  • Row 6: SET SCREW M8, bar fixture, has blank torque cells and remark 1. Remark 1 supplies medium-grade adhesive, for example Loctite 243, and 19.5 Nm (14.4 ft. lbs.). The blank is not zero torque. No set-screw length or order number is supplied.
  • These are the six rows printed in the 1996 introduction. Later TI03/1997 and TI14/1999 distinguish AV-sleeve fixing/clamping screws and gearbox clamps with other values; do not reconcile differently named locations solely by thread size or transfer 19.5 Nm to the bar nut.
  • The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.

Source: TI 47/1996, p. 3 — HT 75 introduction: six fastening rows and M8 adhesive condition.

No additional parts-table entry added.

Service note · HT 70

HT 70: 1998 cutting attachment

12-inch Rollomatic Mini, 3/8-inch Picco-Micro-Mini (PMN), 44 drive links and a seven-tooth 3/8 P spur sprocket form the printed combination.

  • The printed cutting attachment is: 12-inch cutting length; 3/8-inch Oilomatic chain, PICCO-MICRO-MINI (PMN), 44 DRIVE LINKS; Rollomatic Mini guide bar; 7-TOOTH 3/8 P SPUR SPROCKET.
  • The source does not give a chain gauge, bar mount identifier, bar/chain/sprocket order number or alternative-length compatibility. No such value is inferred from PMN branding, the later IPL, or an assumed modern replacement.
  • This is the introductory combination, not a claim that every 12-inch or every 3/8-inch chain fits. The retained shared catalog sheets are navigation references only.
  • Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.

Source: TI 35/1998, p. 2 — Section 3 complete.

No additional parts-table entry added.

Service note · HT 70

HT 70: carburetor kit and separate lubricant applications

Kit 4227 007 1060 is listed for Zama C1Q-S28C / C1Q-S41; oil-seal, gearbox and drive-shaft greases have separate order numbers and tube sizes.

  • Carburetor parts kit 4227 007 1060 is assigned to Zama C1Q-S28C and C1Q-S41 as printed. Do NOT silently change those suffixes to the later catalog sheet C1Q-S28E / C1Q-S41C. The shared sheet is only navigation; kit contents and applicability to later suffixes are not established here.
  • Lube grease 0781 120 1111, 225 g / 8 oz TUBE: OIL SEALS. Lube grease 0781 120 6602, 40 g / 1.4 oz TUBE: GEAR BOX. Lube grease 0781 120 1109, 80 g / 2.8 oz TUBE: DRIVE SHAFT. These are package sizes, NOT quantities to install.
  • The three printed application labels are retained independently. Do not swap grease applications, infer equivalence with other editions or treat tube mass as a gearbox fill. No maintenance interval, fill amount or replacement product is specified by this table. Existing lubricant/application conflicts in other notes remain unchanged.
  • Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.

Source: TI 35/1998, p. 3 — Section 5.2 complete table; section 5.1 reference retained separately.

Part numbers (4)
  • 4227 007 1060 — Carburetor parts kitHistorical servicing kit · HT 70; TI35/1998 Zama C1Q-S28C and C1Q-S41 only as printed
  • 0781 120 1111 — Lube grease, 225 g / 8 oz tubeOil-seal servicing aid · HT 70; TI35/1998 oil seals; package size, not installed quantity
  • 0781 120 6602 — Lube grease, 40 g / 1.4 oz tubeGearbox servicing aid · HT 70; TI35/1998 gear box; package size, not fill amount
  • 0781 120 1109 — Lube grease, 80 g / 2.8 oz tubeDrive-shaft servicing aid · HT 70; TI35/1998 drive shaft; package size, not installed quantity

Service note · HT 70

HT 70: repair references and historical parts-list issue

Available HT70 repair dependencies reviewed; exact historical handbooks, owner precautions and the 3.98 IPL remain documented source gaps.

  • Section 5.1 says the same special servicing tools are used as for FS 85 brushcutters. Section 6.1 says setting/testing data and other information are the same as HT 75 and FS 85 brushcutters (SHAFT). This supplies no numeric setting, torque or tool order number; it does not make the HT70 a brushcutter.
  • The named service manual is FS 75, 80, 85, FC 75, HL 75; missing GEARHEAD procedures are delegated to TI03/1997. Applicable retained TI procedures and later explicitly HT70-bound Components (2005-04), Powerhead (2004-03) and CombiTools (2007-02) sections have been reviewed separately. Exact historical FS manual and E14/E20 tensioner-manual editions remain bounded source gaps. Later sources do not prove original 1998 configuration; HT75-only revisions are not silently rebound to HT70.
  • The cited historical manual omits Servicing the Carburetor, Troubleshooting and standard procedures, delegating them to separate CARBURETOR and STANDARD REPAIRS, TROUBLESHOOTING handbooks. Neither requested handbook is established in the retained PDF inventory, reviewed manual headers and reference-document index. The available Chain and Bar, Special Tools, 019 T, 020 T and HS/BG service manuals are different works. Their references to handbooks are not the handbooks themselves. This is a bounded source gap, not universal absence; later HT70-specific carburetor/troubleshooting content remains separately reviewed evidence.
  • If the unit is STARTED during repair or maintenance, section 6 requires all LOCAL SAFETY REGULATIONS and the OWNER’S MANUAL safety precautions. The exact HT70 owner-safety source is not established in the retained archive inventory or HT70/HT75 document links; repair-manual safety paragraphs do not replace it. No start-up or under-load test was performed, and review closure is not bench readiness.
  • Section 7 says HT70 parts will be incorporated in the existing HT75 list and are included in the 3.98 microfiche/CD-ROM issue. The retained 2012 catalog links HT70/HT75 to later IPL documents, including a gearhead entry marked 11.2005 and a gear-housing conversion kit marked 22.2011. No exact 3.98 edition is established by that index or the retained PDF inventory. Later drawings are useful navigation, not proof of 1998 parts, supersession, introduction serial, current stock or publication authorization. The copyright/footer adds no interchange assertion.
  • Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.

Source: TI 35/1998, p. 3 · TI 35/1998, p. 4 — Sections 5.1, 6 safety paragraph, 6.1 and 7; retained dependency review complete with bounded exact-source gaps.

No additional parts-table entry added.

Service note · HT 70

HT 70: delegated historical gearhead disassembly

TI03/1997 gearhead reference: cover, ring, pinion and bearings retain their illustrated positions; circlip pliers 0811 611 8200 are specified.

  • Loosen gearbox clamp screws and pull gearbox off protective tube. Remove sprocket cover and sprocket, remove oil tank (section 2.2), pull ring (1) from shaft (2), and remove screws (3) and gear cover (4). This original sequence does not include the later friction-clutch supplement; it is not a procedure for every later sprocket configuration.
  • Remove pinion assembly (5) from housing (6). Use circlip pliers (8), order number 0811 611 8200, to remove circlip (7); pull ball bearings (9) off the pinion. Remove shaft assembly (2) and pull ball bearings (10 and 11) off it.
  • The diagrams distinguish the paired pinion bearings (9) and the two shaft bearings (10,11). These are illustration callouts, NOT order numbers or proof that the bearings are interchangeable. No bearing size, puller force or heating temperature is supplied.
  • TI03/1997 is a historical, superseded source: TI14/1999 explicitly replaces it but names HT75. The later lubricant changes and friction-clutch qualification are retained in the separate edition-boundary note, not silently prescribed for every HT70. TI03/1997 requires trained, authorized personnel and use of the illustrated parts list for orientation.
  • Historical HT 70 only through the explicit TI35/1998 section 6.1 GEARHEAD reference to TI03/1997. This is not inheritance of the HT75 telescopic shaft, paired-shaft replacement, or its labor allowance. Printed series 4138 and catalog 4137 remain separate identities; shared-sheet navigation is not proof of interchange or applicability to later configurations. No hardware operation was performed.

Source: TI 35/1998, p. 4 — Section 6.1 explicit HT70 gearhead delegation; Complete 2.1 disassembly and bearing-position drawings.

Referenced bulletin evidence: TI 3/1997, p. 3 · TI 3/1997, p. 4 — Complete 2.1 disassembly and bearing-position drawings.

Part numbers (1)
  • 0811 611 8200 — Circlip pliersSpecified historical gearhead service tool · Historical HT70 gearhead through TI35/1998 section 6.1 and TI03/1997 section 2.1; not blanket later fitment

Service note · HT 70

HT 70: bearing order, 8 g fill and staged tightening

Historical gearhead assembly uses an 8 g cavity fill, Dirko 0783 830 2120 and two separately staged 6.5 Nm tightening operations.

  • Press bearing (10) onto the pinion end of shaft (2), then bearing (11), and insert shaft assembly into housing (6). Fit the pinion bearings (9) and circlip (7) in the positions shown by drawing 390RA022. No bearing order number is supplied.
  • Place 8 g (printed 0.3 oz) gear lubricant into the gear-housing cavity before inserting pinion (5). This is an ASSEMBLY FILL, not a lubricant-tube mass, maintenance interval or oil-tank capacity. TI03/1997 gives no lubricant order number. TI35/1998 separately lists 0781 120 6602 for the gearbox in a 40 g tube; the later HT75 lubricant changes are not silently merged with that 1998 table.
  • Thinly coat the edge of the housing with Dirko sealant 0783 830 2120. Fit cover (4), install screws (3), and tighten all EXCEPT THE ARROWED CLAMP SCREWS to 6.5 Nm (printed 5 lbf.ft).
  • Press ring (1) onto shaft (2). Slide gearbox onto tube while turning it back and forth to engage the drive-shaft square with the internal square of the drive pinion. Push fully home and align; ONLY THEN tighten gearbox clamp screws to 6.5 Nm (printed 5 lbf.ft). Do not clamp before engagement/seating/alignment.
  • TI14/1999 prints the same 6.5 Nm as 4.8 lbf.ft; retain the edition-specific rounded imperial values, not two invented metric torque specifications. Existing sealant-number differences in other notes remain unresolved; this source does not establish a replacement for 0783 830 2120.
  • TI03/1997 is a historical, superseded source: TI14/1999 explicitly replaces it but names HT75. The later lubricant changes and friction-clutch qualification are retained in the separate edition-boundary note, not silently prescribed for every HT70. TI03/1997 requires trained, authorized personnel and use of the illustrated parts list for orientation.
  • Historical HT 70 only through the explicit TI35/1998 section 6.1 GEARHEAD reference to TI03/1997. This is not inheritance of the HT75 telescopic shaft, paired-shaft replacement, or its labor allowance. Printed series 4138 and catalog 4137 remain separate identities; shared-sheet navigation is not proof of interchange or applicability to later configurations. No hardware operation was performed.

Source: TI 35/1998, p. 4 — Section 6.1 explicit HT70 gearhead delegation; Complete 2.1 assembly, sealant, fill and mounting sequence.

Referenced bulletin evidence: TI 3/1997, p. 4 · TI 3/1997, p. 5 — Complete 2.1 assembly, sealant, fill and mounting sequence.

Referenced bulletin evidence: TI 14/1999, p. 1 · TI 14/1999, p. 4 · TI 14/1999, p. 5 · TI 14/1999, p. 6 — Supersession, HT75 model boundary, sections 2.1–2.4 and 3 lubricant changes; comparison only.

Part numbers (1)
  • 0783 830 2120 — Dirko sealantHistorical housing-edge sealant · Historical HT70 gearhead through TI35/1998 section 6.1 and TI03/1997 section 2.1; not blanket later fitment

Service note · HT 70

HT 70: delegated oil tank and pump service

Counterclockwise tank removal; temporary M5 screw at least 25 mm long; pump groove faces the tube mount in TI03/1997.

  • Remove filler cap with its retainer, remove oil-tank screws, and swivel tank COUNTERCLOCKWISE to remove it. Reassemble tank parts in reverse order.
  • With tank removed, pull rubber buffer (1) from gearbox housing and remove strainer (2). Thread an M5 screw AT LEAST 25 mm LONG into the oil pump and pull it out by the screw. No buffer, strainer, pump or screw order number is printed.
  • Insert pump according to the symbol beside the opening: the FULL-LENGTH GROOVE MUST FACE THE TUBE MOUNT. Thread the M5 screw into the pump and press the pump into position; REMOVE THE SCREW and reassemble remaining parts in reverse order. The screw is a temporary extraction/pressing aid, not a retained pump component. No pressing depth, force or torque is specified.
  • TI14/1999 uses rubber seal/filter screen wording, adds cleaning the oil passages and describes the slot facing the ENGINE. Those are separately dated HT75 comparison statements, not a silently merged HT70 sequence; actual housing symbol/configuration remains essential.
  • TI03/1997 is a historical, superseded source: TI14/1999 explicitly replaces it but names HT75. The later lubricant changes and friction-clutch qualification are retained in the separate edition-boundary note, not silently prescribed for every HT70. TI03/1997 requires trained, authorized personnel and use of the illustrated parts list for orientation.
  • Historical HT 70 only through the explicit TI35/1998 section 6.1 GEARHEAD reference to TI03/1997. This is not inheritance of the HT75 telescopic shaft, paired-shaft replacement, or its labor allowance. Printed series 4138 and catalog 4137 remain separate identities; shared-sheet navigation is not proof of interchange or applicability to later configurations. No hardware operation was performed.

Source: TI 35/1998, p. 4 — Section 6.1 explicit HT70 gearhead delegation; Complete 2.2–2.3 tank removal, extraction aid, pump orientation and assembly.

Referenced bulletin evidence: TI 3/1997, p. 5 · TI 3/1997, p. 6 — Complete 2.2–2.3 tank removal, extraction aid, pump orientation and assembly.

Referenced bulletin evidence: TI 14/1999, p. 1 · TI 14/1999, p. 4 · TI 14/1999, p. 5 · TI 14/1999, p. 6 — Supersession, HT75 model boundary, sections 2.1–2.4 and 3 lubricant changes; comparison only.

No additional parts-table entry added.

Service note · HT 70

HT 70: gearhead corrections and tensioner dependency

TI14/1999 supersedes the delegated source but names HT75; lubricant changes, friction-clutch TI36/1998 and E14/E20 tensioner manual remain separately scoped.

  • TI35/1998 section 6.1 expressly delegates HT70 GEARHEAD procedures to TI03/1997. That is positive historical applicability evidence for the referenced gearhead sections, not permission to extend all HT75 shaft procedures or assume all future HT75 revisions apply to HT70.
  • TI14/1999 page 1 explicitly supersedes and replaces TI03/1997 and names HT75, series 4138. Its section 2.1 adds TI36/1998 for versions with a FRICTION CLUTCH. The retained TI36/1998 has now been reviewed: it expressly covers HT75 and its telescopic-drive-shaft overload case; it does not establish HT70 retrofit applicability. See the separate friction-clutch scope note.
  • TI14/1999 says further testing changed lubricant use: section 3.1 assigns brushcutter gear lubricant 0781 120 1117 / 0781 120 1118 to the GEARBOX; section 3.2 specifies STIHL synthetic two-stroke engine oil for DRIVE SHAFTS; section 3.3 assigns grease 0781 120 6602 to the DRIVE SHAFT IN PLASTIC LINER. These are HT75 comparison statements, not an HT70 product-substitution list.
  • TI35/1998 instead lists 0781 120 6602 for GEARBOX and0781 120 1109 for DRIVE SHAFT, while 0781 120 1111 is for OIL SEALS. Preserve this application conflict. The HT70 rigid-shaft exception and later bulletin model scope prevent silently swapping those applications or treating tube sizes as fill quantities.
  • TI03/1997 section 2.4 supplies ONLY a reference to Repair Manual E14, E20 for the chain tensioner. TI14/1999 section 2.4 also names E140, E160, E180C. The available 2003-01 electric-saw manual has been visually reviewed as comparison evidence; it is not the exact E14/E20 source and no HT70 procedure is silently transferred. See the separate tensioner-manual edition note.
  • Telescopic-shaft sections 1.1–1.3 and the HT75 shaft labor time are excluded from this gearhead inheritance. The separate TI35/1998 HT70 repair-time note retains its own table. No tensioner procedure or friction-clutch servicing is fabricated.
  • TI03/1997 is a historical, superseded source: TI14/1999 explicitly replaces it but names HT75. The later lubricant changes and friction-clutch qualification are retained in the separate edition-boundary note, not silently prescribed for every HT70. TI03/1997 requires trained, authorized personnel and use of the illustrated parts list for orientation.
  • Historical HT 70 only through the explicit TI35/1998 section 6.1 GEARHEAD reference to TI03/1997. This is not inheritance of the HT75 telescopic shaft, paired-shaft replacement, or its labor allowance. Printed series 4138 and catalog 4137 remain separate identities; shared-sheet navigation is not proof of interchange or applicability to later configurations. No hardware operation was performed.

Source: TI 35/1998, p. 4 — Section 6.1 explicit HT70 gearhead delegation; Section 2.4 tensioner reference and later correction boundaries.

Referenced bulletin evidence: TI 3/1997, p. 6 — Section 2.4 tensioner reference and later correction boundaries.

Referenced bulletin evidence: TI 14/1999, p. 1 · TI 14/1999, p. 4 · TI 14/1999, p. 5 · TI 14/1999, p. 6 — Supersession, HT75 model boundary, sections 2.1–2.4 and 3 lubricant changes; comparison only.

No additional parts-table entry added.

Service note · HT 70

HT 70: HT75 friction-clutch change is not an HT70 retrofit approval

TI36/1998 serial 2 39 949 387 and kit 4138 007 1001 apply to HT75; HT70 applicability is not established.

  • TI36/1998 names only HT75, series 4138. Its section 1 introduces the chain-sprocket friction clutch from serial 2 39 949 387 to reduce load on the MULTI-PART TELESCOPIC drive shaft. TI35/1998 explicitly distinguishes the HT70 RIGID shaft. The shared gearhead drawing and shared catalog sheet do not transfer that serial or establish an HT70 conversion.
  • Section 1.4.3 says EVERY HT75 can be converted with complete kit 4138 007 1001; it does not say every HT70. The separate kit instruction sheet identifies replacement parts. No HT70 retrofit or individual part interchange is inferred from that statement or from the section 1.5 parts table.
  • The left-hand collar screw, complete three-cup-spring replacement, washers supplied with the sprocket, 6 Nm collar-screw torque and 5–14 Nm slip-test range in TI36/1998 remain HT75 friction-clutch guidance. They are not HT70 setting/testing specifications. The ring supply conflict between section 1.4.2 and the spare-availability table remains retained in the existing HT75 notes.
  • TI14/1999 points versions WITH a friction clutch to TI36/1998, but also names HT75. This resolves the dependency review as a MODEL/CONFIGURATION BOUNDARY, not proof that no HT70 ever had a friction clutch. The older TI03/1997 sprocket-removal sequence must not be assumed suitable for an unverified later assembly.
  • Historical HT 70 only: TI35/1998 provides the repair-source context, not blanket inheritance of later HT75 revisions. Printed series 4138 and catalog 4137 remain separate identities. No hardware operation was performed.

Source: TI 35/1998, p. 4 — HT75 friction-clutch change is not an HT70 retrofit approval.

Referenced bulletin evidence: TI 36/1998, p. 1 · TI 36/1998, p. 2 · TI 36/1998, p. 3 · TI 36/1998, p. 4 — HT75-only model heading, telescopic-shaft purpose, retrofit scope and service/table context.

No additional parts-table entry added.

Service note · HT 70

HT 70: chain-tensioner manual found, exact historical applicability unresolved

The available 2003-01 E140/E160/E180C manual separates front, side and quick tensioners; it is not the exact E14/E20 source.

  • TI35/1998 delegates HT70 gearhead work to TI03/1997; section 2.4 of that source says only see Repair Manual E14, E20. TI14/1999 expands the manual reference to E140, E160, E180C, but its heading remains HT75. That later reference is a useful locator, not by itself an HT70 applicability bridge.
  • RA_100_00_01_02.pdf is locally available. Its cover says E140, 160, 180 and 2003-01; the introduction names E140, E160 and E180C. The 2006 layout timestamp on the cover is distinct from the printed edition. It must not be renamed an E14/E20 manual or treated as the original 1997/1998 edition.
  • PDF18 (printed17) contains separate front and side chain-tensioner sections 7.1 and 7.2. The front mechanism uses a tensioning nut, adjusting screw and cover; the side mechanism additionally distinguishes thrust pad, spur gear and tensioner slide. Its side-tensioner teeth inspection and lubricating-grease reference belong to that mechanism. PDF19 (printed18), section 7.3, concerns the quick-tensioner wingnut and cover. Adjacent chain-brake section 8.1 is not tensioner service.
  • These illustrations are reviewed comparison evidence, NOT three interchangeable HT70 procedures. No electric-motor housing removal, chain-brake procedure, quick-tensioner conversion, grease order number or torque is prescribed for HT70 from these pages. Exact HT70 mechanism/edition evidence is still required before transferring the procedure.
  • The reused bounded inventory contains 808 PDF paths; the available electric-saw candidate and HT components manual were checked directly. No exact E14/E20 repair manual was established in that inventory. This is a named historical-source gap, not universal absence, nor a reason to skip the other locally available HT70 manual sections.
  • Historical HT 70 only: TI35/1998 provides the repair-source context, not blanket inheritance of later HT75 revisions. Printed series 4138 and catalog 4137 remain separate identities. No hardware operation was performed.

TI dependency: TI 35/1998, p. 4 — chain-tensioner manual found, exact historical applicability unresolved.

Referenced bulletin evidence: TI 3/1997, p. 6 — Section 2.4 exact E14/E20 reference.

Referenced bulletin evidence: TI 14/1999, p. 6 — Section 2.4 later electric-saw reference; HT75 comparison only.

Later manual evidence: STIHL E 140, 160, 180 (introduction: E 180 C) (2003-01), section Edition/model identity and complete sections 7.1–7.3; comparison only, not an admitted HT70 procedure, PDF pages 1, 3, 18, 19

No parts-table entry added. Tool references, where present, are retained in the manual notes above.

Wrong number or missing part for the HT 70, HT 75? Report a correction →