Stihl 4137 · Section Q · 15 of 24 · 34 parts
Drive tube assembly HT 75
Fits HT 75.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (34)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4138 710 7105 | Drive tube assembly Ø 38 mm / 1 1/2'' | 1 |
| 2 | 4138 716 6500 | Clamp | 2 |
| 3 | 9645 948 7995 | O-ring 40x4 | 2 |
| 4 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 4 |
| 5 | 9022 341 1300 | Spline screw IS-M6x20 | 1 |
| 6 | 9210 260 0700 | Hexagon nut M5 | 4 |
| 7 | 9210 319 0900 | Hexagon nut M6 | 1 |
| 8 | 9008 319 1350 | Hexagon head screw M6x25 | 1 |
| 9 | 4138 716 1200 | Wing nut | 1 |
| 10 | 4182 791 7201 | Sleeve | 2 |
| 11 | 4182 710 7111 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 12 | 4138 740 3200 | Bearing | 1 |
| 13 | 9438 003 3171 | Blind rivet 4x6.5 | 1 |
| 14 | 4138 740 3200 | Bearing | 2 |
| 15 | 4138 711 9100 | Spring | 2 |
| 16 | 4138 740 3205 | Bearing | 1 |
| 17 | 4182 710 3203 | Drive shaft | 1 |
| 18 | 9458 621 1130 | Snap ring A12 | 1 |
| 19 | not sold separately | Drive shaft not available as a separate item | 1 |
| 20 | 9455 621 1520 | Circlip 15x1 | 1 |
| 21 | 4182 710 3204 | Drive shaft | 1 |
| 22 | 4182 710 3201 | Drive shaft | 1 |
| 23 | 4182 740 3501 | Driver | 1 |
| 24 | 4138 711 9002 | Ring | 2 |
| 25 | 4138 711 7300 | Flexible liner 1241 mm / 48 7/8'' | 1 |
| 26 | 4182 711 7301 | Flexible liner 400 mm | 1 |
| 27 | 4182 710 7106 | Drive tube assembly Ø 25.4 mm / 1'' | 1 |
| 28 | 9291 021 0100 | Washer 4.3 | 3 |
| 29 | 9438 003 3171 | Blind rivet 4x6.5 | 2 |
| 30 | 4140 007 1006 | Hose clamp kit | 1 |
| 31 | 9022 341 1270 | Spline screw IS-M6x14 | 1 |
| 32 | 0781 120 6000 | Grease for telescopic boom option | 1 |
| 33 | 0781 957 9000 | Press fluid OH 723 option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4182 710 7110 | Drive tube assembly Ø 38 mm / 1 1/2'' | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HT 75
HT 75: paired drive shafts and separate lubricant locations
Replace both splined shafts together; keep synthetic oil, liner grease and gearbox lubricant roles distinct.
- The external splined shaft runs in ball bearings in the fixed tube; the internal splined shaft runs in the plastic liner and ball bearing in the sliding tube. Their close tolerances require replacement as a pair. A damaged or blue-discolored shaft calls for a new external/internal shaft assembly, not one loose shaft.
- Remove the gearbox before withdrawing the internal shaft with liner and retaining ring. Remove liner/ring, release the control-handle clamps, remove AV-sleeve fixing screw (2), release clamp screw (3), withdraw the drive tube and then the external shaft.
- New shafts are pre-lubricated: only the plastic liner internal bore needs lubrication. Page 2 instructs a uniform coating of grease 0781 120 6602 on the outside of the drive shaft and prohibits pumping grease directly into the tube. Section 3.3 identifies this as the drive shaft in the plastic liner, not the spline-to-spline oiling instruction.
- If cleaning is needed before installation, separate the shafts and completely coat the external splined shaft with STIHL synthetic two-stroke engine oil before reassembly. Section 3.2 repeats this oil assignment. Do not replace it with gearbox grease or infer an oil part number.
- Fit ring and liner to the internal shaft, fully compress the telescopic tube and insert to the stop while turning back and forth so the ring does not snag on the stop or mounting rivet. Do not force it home; only the square end is visible.
- Insert the external shaft into the short tube to its stop, dimension A = 11 mm as drawn. Only the square end is visible; make sure the internal shaft is not pushed out. Align the drive-tube holes on installation; a helper can turn the shaft and the source permits holding the clutch drum with a screwdriver if necessary.
- Tighten the AV-sleeve fixing screw to 2.5 Nm (1.8 lbf.ft) and its clamp screw to 5 Nm (3.7 lbf.ft), then reinstall the gearbox under section 2.1. These two torques are not the gearbox clamp torque.
- The retained later IPL lists telescopic-boom grease 0781 120 6000. TI14/1999 specifies 0781 120 6602; no equivalence or supersession is established here.
- TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
- Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.
Source: TI 14/1999, p. 1 · TI 14/1999, p. 2 · TI 14/1999, p. 6 — 1.1 and 3.2–3.3: matched shafts, removal, installation and two distinct lubrication interfaces.
Part numbers (1)
- 0781 120 6602 — Grease for drive shaft in plastic linerLocation-specific lubricant · HT 75 configuration described in TI14/1999 only
Service note · HT 75
HT 75: telescopic bearing and drive tube orientation
Original blind rivets, engine-end orientation and spring/bearing order are retained without guessed part numbers.
- Mark the engine end on the drive-tube handle hose before disassembly. Remove shaft and liner under section 1.1; remove the harness-eye clamp screw, spread the clamp and lift it away.
- Release star grip nut (1), extend long tube (2) to relax the springs, loosen screws (3) and remove clamp (4). Withdraw the long tube at the gearbox end. Loosen screws (5,6), remove clamp (7), withdraw short tube (8) at the engine end and remove springs (9) and bearings (10).
- Replace worn bearings. For riveted bearings, remove blind rivet (12) and bearing (13); align bearing and tube (14) holes and secure only with an original STIHL blind rivet. No rivet or bearing order number is printed in this bulletin; do not assign numbers from the later IPL by diagram position alone.
- At the marked engine end, insert bearings (10), ball-bearing end first, and springs (9) into outer tube (11) in the illustrated order. If the tube is new or unmarked, view it from the engine end: rivet A is at the top and both guides B are on the right. Do not reverse the viewing direction.
- Slip clamp (7) over short tube (8), insert both into the engine end, and tighten screws (6). Pull the short tube out to its stop before tightening screw (5); assemble the remaining parts in reverse order. No numerical torque is given for screws (5,6) here; do not borrow the section 1.1 AV-sleeve values.
- Section 1.3 requires removal of drive shaft, plastic liner and bearings before replacing a damaged drive tube. It does not supply a replacement tube number or authorize cross-version interchange.
- TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
- Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.
Source: TI 14/1999, p. 2 · TI 14/1999, p. 3 · TI 14/1999, p. 4 — 1.2–1.3: liner, bearings, springs, rivets, orientation and damaged tube.
No additional parts-table entry added.
Service note · HT 75
HT 75: superseded 1997 paired-shaft service
Superseded by TI14/1999. Retain paired replacement, historical lubricant wording and extended-tube assembly without substituting the 1999 sequence.
Later reviewed guidance: HT 75: paired drive shafts and separate lubricant locations
- Superseded historical instruction: TI14/1999 explicitly supersedes and replaces TI03/1997. Follow the linked later source for its revised procedure; the two versions must not be blended into an invented sequence.
- TI03/1997 restricts inspection, service and repair to trained, authorized personnel and refers to the illustrated spare-parts list for orientation. This is an offline source record, not a hardware experiment.
- The source names only HT 75, type 4138. The exact-model IPL is filed under 4137 and also names HT 70; that navigation link does not establish series equivalence, extend this procedure to HT 70 or prove applicability to every later HT 75. No production serial is printed.
- The rigid part contains a profiled shaft in ball bearings; the telescoping part contains the inner-profile shaft in protective tubing and ball bearings. Always replace both shafts as a pair because of their high precision; no shaft order numbers are printed.
- Remove gearing under section 2.1; withdraw profiled inner shaft (1) with protective tubing and circlip, then remove tubing and circlip. Release control-handle clamping-collar screws, remove AV-sleeve fixing screw (2), loosen clamping screw (3), withdraw protective tube and pull out profiled shaft (4).
- Shafts arrive oiled; only the profiled inner shaft in the protective tubing needs lubrication. Apply grease uniformly to the drive shaft, never force it directly into the protective tube. The 1997 TI supplies no grease part number or quantity.
- If cleaning is needed, completely separate the shafts first. Page 1 literally specifies a silicone spray lubricant such as WD40 or equivalent on the profiled shaft before assembly. Preserve this historical product/category wording without certifying WD40 composition or general lubricant equivalence. TI14/1999 instead specifies STIHL synthetic two-stroke engine oil for the external splined shaft; do not combine those instructions.
- 1997 assembly order: insert profiled shaft (4) into its protective tube as far as possible, leaving only the square visible. Fit ring and protective tubing to the inner shaft; draw the telescoping shaft fully apart. An assistant steadies the profiled shaft so it is not pushed out while the inner shaft, tubing and ring are inserted.
- Turn the inner shaft back and forth during insertion so the circlip does not catch on the stop or fixing rivet. Do not force it into final position; only the square remains visible. Slide the telescoping shaft together without pushing the inner shafts out. This fully-apart sequence differs from the later 1999 fully-compressed instruction; it is not a choice of equivalent methods.
- Push the protective tube in until its holes line up; an assistant may turn the drive shaft during insertion. Tighten fixing screw to 2.5 Nm (printed 2 lbf.ft) and clamping screw to 5 Nm (printed 4 lbf.ft); these rounded source units are not the gearbox torque. Refit gearing under section 2.1. No 11 mm shaft dimension is printed in this edition.
Source: TI 3/1997, p. 1 · TI 3/1997, p. 2 — Complete1.1: matched shafts, removal, historical lubrication, extension/assembly order and AV-sleeve torques.
No additional parts-table entry added.
Service note · HT 75
HT 75: superseded 1997 bearing and tube service
Superseded by TI14/1999. Retain motor-end marking, bearing/spring direction and pop-rivet alignment with the original callout numbers.
Later reviewed guidance: HT 75: telescopic bearing and drive tube orientation
- Superseded historical instruction: TI14/1999 explicitly supersedes and replaces TI03/1997. Follow the linked later source for its revised procedure; the two versions must not be blended into an invented sequence.
- TI03/1997 restricts inspection, service and repair to trained, authorized personnel and refers to the illustrated spare-parts list for orientation. This is an offline source record, not a hardware experiment.
- The source names only HT 75, type 4138. The exact-model IPL is filed under 4137 and also names HT 70; that navigation link does not establish series equivalence, extend this procedure to HT 70 or prove applicability to every later HT 75. No production serial is printed.
- Mark the motor side on the protective-tube handle hose. Remove drive shaft under section 1.1, drawing out protective tubing with it. Remove carrying-ring screw, spread and remove carrying ring.
- Unscrew star-handle nut (1) and screws (2) on clamping element (3); remove element and pull out long protective tube (4) at the gear end. Loosen screws (5), remove clamping element (6) and pull out short protective tube (7) at the motor end.
- Remove bearings (8) and springs (9) from outer tube (10); replace worn bearings. For riveted bearings remove pop rivet (11) and bearing (12), line up holes in bearing (12) and tube (13), and secure with the pop rivet. No rivet dimensions or order number are provided.
- At the marked motor-side end insert bearings (8), ball-bearing end first, and springs (9) into outer protective tube (10) in the illustrated order; assemble remaining parts in reverse order. The 1997 callouts differ from the later 1999 drawing and cannot be transferred as part numbers.
- Section 1.3: remove drive shaft, protective tubing and bearings before replacing a broken or bent protective tube. No tube number, new/unmarked-tube alignment diagram, or clamp torque is supplied here; later instructions remain linked, not silently inserted into this edition.
Source: TI 3/1997, p. 2 · TI 3/1997, p. 3 — Complete1.2–1.3: protective tubing, bearings, spring order, rivet alignment and broken/bent tube replacement.
No additional parts-table entry added.
Service note · HT 75
HT 75 introduction: original drive-shaft and gear grease listing
0781 120 6602, 40 g tube, is listed for both profiled drive shaft and gear; later lubricant roles remain separate.
Later reviewed guidance: HT 75: paired drive shafts and separate lubricant locations · HT 75: gearbox bearing order, sealant and 8 g lubricant
- Section 5.2 lists GREASE (40 g tube), 0781 120 6602, for drive shaft (profiled shaft), gear, with remark NEW. The 40 g is package size, not an instruction to put 40 g into either assembly.
- Section 1 calls the profiled shaft pre-lubricated. This TI supplies no application quantity, refill interval or gear assembly procedure.
- Already-reviewed TI14/1999 distinguishes grease 0781 120 6602 at the plastic liner, synthetic two-stroke oil on the external splined shaft and brushcutter gear lubricant at the pinion cavity. Its different assignments must not be silently merged into this 1996 gear-grease row. TI03/1997 is explicitly superseded by TI14/1999; that does not prove every line of TI47/1996 was explicitly superseded.
- The later IPL lists telescopic-boom grease 0781 120 6000. Neither a similar description nor the retained 1996 number establishes lubricant equivalence.
- The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.
Source: TI 47/1996, p. 2 · TI 47/1996, p. 3 — HT 75 introduction: original drive-shaft and gear grease listing.
Referenced bulletin evidence: TI 14/1999, p. 6 — Previously accepted sections 3.1–3.3, location-specific lubricants; no new review of this lane.
Part numbers (1)
- 0781 120 6602 — Grease, 40 g tubeOriginal drive-shaft / gear aid · HT 75 configuration described in TI47/1996 only
Service note · HT 75
HT 75 introduction: six fastening rows and M8 adhesive condition
2.5 / 3.0 / 4.5 Nm location-specific screws; M8 bar fixture uses medium-grade adhesive and 19.5 Nm.
- Section 6.1 row 1: socket-head screw IS-DG5x12, oil tank / gear housing, 2.5 Nm (1.8 ft. lbs.). The later oil-tank IPL lists IS-D5x20 instead; do not substitute that screw or its number into this historical row.
- Rows 2 and 3: socket-head screw IS-M5x20, clamp / LARGE protective tube and clamp / SMALL protective tube, each 3.0 Nm (2.2 ft. lbs.). Preserve both locations; this is not a general M5 torque.
- Row 4: socket-head screw IS-M6x14, clamping collar / carrying ring, 4.5 Nm (3.3 ft. lbs.). Row 5: socket-head screw IS-M6x20, clamp / power unit / shaft, 4.5 Nm (3.3 ft. lbs.).
- Row 6: SET SCREW M8, bar fixture, has blank torque cells and remark 1. Remark 1 supplies medium-grade adhesive, for example Loctite 243, and 19.5 Nm (14.4 ft. lbs.). The blank is not zero torque. No set-screw length or order number is supplied.
- These are the six rows printed in the 1996 introduction. Later TI03/1997 and TI14/1999 distinguish AV-sleeve fixing/clamping screws and gearbox clamps with other values; do not reconcile differently named locations solely by thread size or transfer 19.5 Nm to the bar nut.
- The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.
Source: TI 47/1996, p. 3 — HT 75 introduction: six fastening rows and M8 adhesive condition.
No additional parts-table entry added.
Wrong number or missing part for the HT 75? Report a correction →